Infiniti FX35, FX50 (S51). Manual - part 1256

INT-26

< REMOVAL AND INSTALLATION >

HEADLINING

15. Insert a small flat-bladed screwdriver (A) into the hole of the

sun-visor holder (1), press while rotating approximately 90
degrees to remove.

16. Using remover tool, remove headlining hidden clip at the back side of headlining.
17. Pull down roof console assembly and disengage metal clips (B)

and dual-lock fastener (A).

CAUTION:

Roof console assembly is crimped from the back of head-
lining. Remove it by disengaging the crimped area of back
of roof console assembly after removing headlining from
the vehicle.

18. Remove headlining (1) from back door.

CAUTION:

• When removing, 2 workers are required.
• Never bend headlining when removing.
• Be careful not to scratch or damage any part of the body while taking out the headlining. 

19. Remove the following parts after removing headlining.

• Roof console assembly. Refer to 

INT-23, "Exploded View"

.

• Map lamp assembly. Refer to 

INL-183, "Removal and Installation"

.

• Personal lamp assembly. Refer to 

INL-193, "Removal and Installation"

.

JMJIA1706ZZ

: Metal clip

JMJIA1008ZZ

JMJIA2066ZZ

HEADLINING

INT-27

< REMOVAL AND INSTALLATION >

C

D

E

F

G

H

I

K

L

M

A

B

INT

N

O

P

• Headlining harness. 

INSTALLATION

Install in the reverse order of removal.

CAUTION:

• As for guide, install first sun-visor holder (LH/RH) and then the rear hidden clips at the back side of

headlining.

• Be careful not to bend the headlining when installing.

INT-28

< REMOVAL AND INSTALLATION >

LUGGAGE FLOOR TRIM

LUGGAGE FLOOR TRIM

Exploded View

INFOID:0000000005240803

1.

Luggage finisher center

2.

Belt assembly

3.

Luggage side finisher upper (LH)

4.

Luggage side finisher lower (LH)

5.

Luggage side finisher upper (RH)

6.

Luggage side finisher lower (RH)

7.

Seatback control finisher cap

8.

Seatback control cable finisher

9.

Rope hook

JMJIA2067ZZ

LUGGAGE FLOOR TRIM

INT-29

< REMOVAL AND INSTALLATION >

C

D

E

F

G

H

I

K

L

M

A

B

INT

N

O

P

Removal and Installation

INFOID:0000000005240804

REMOVAL

LUGGAGE REAR PLATE

1.

Fully open back door.

2.

Remove tonneau cover assembly.

3.

Open and pull luggage finisher center (1) backwards, till the
bolts are visible.

4.

Remove both bolts and then remove luggage finisher center.

5.

Remove the clip (A), disconnect the woofer harness connector
(B), and then remove the woofer (1) and spire tire (2). Refer to

AV-572, "Removal and Installation"

.

6.

Remove the rear seat assembly. Refer to 

SE-94, "Removal and Installation"

.

7.

Remove the luggage floor finisher front (LH/RH).

8.

Remove back door weather-strip. 

9.

Disengage the rear plate (1) fixing clips with a remover tool (A)
then remove it.

10. Hold both sides of luggage rear plate, pull upwards to remove.

LUGGAGE FLOOR SPACER

10. Luggage room lamp

11. Luggage floor finisher front

12. Luggage floor spacer (LH)

13. Luggage rear plate cap

14. Luggage rear plate

15. Luggage floor spacer (RH)

16. Tonneau cover assembly

17. Tonneau cover (Back door trim side)

18. Luggage side finisher lid

19. Bose woofer

: Clip

: Pawl

: Metal clip

: Bolt

JMJIA1570ZZ

JMJIA2069ZZ

: Clip

: Pawl

JMJIA2074ZZ