Infiniti FX35, FX50 (S51). Manual - part 1072

EXT-38

< REMOVAL AND INSTALLATION >

ROOF SIDE MOLDING

Install from roof side molding rear end to front end in this order after temporarily holding.

REMOVAL AND INSTALLATION OF ROOF SIDE MOLDING CLIP

Removal

1.

Remove roof side molding.

2.

Heat adhesive tape interface using a dryer, and then peel roof side molding clips (body side) using long-
nose pliers.

CAUTION:

Be careful not to damage the body.

Installation

1.

Clean tape removed surface with a shop cloth soaked in white gasoline or IPA.

2.

Use two-part epoxy adhesive.

3.

Apply adhesive evenly to clip tape surface.

4.

Position applied parts to the proper location, and then sufficiently press-fit until the adhesive protrudes to
tape side.

5.

Tape clips after press fit, and temporarily hold it for specified time based on the following items.

6.

Install from roof side molding rear end to front end in this order after temporarily holding.

CAUTION:

• Use double-faced adhesive tape after hardening for clips. 
• Securely insert molding rear end cap onto roof rear end cutout (installation standard).
• When installing roof side molding of windshield portion, check that molding fastener is securely

inserted and then press in.

• Never wash the vehicle within 24 hours so as to keep adhesive.

Adhesive

: 3M-weld DP–100 or an equivalent

Thickness

: Approximately 0.5 mm (0.020 in)

Press-fit limit

: 19.6 N (2.0 kg - 4.41 lb) 

×

 2 seconds

 5 to 10

°

C (41 to 50

°

F)

: 1 hour or more

11 to 23

°

C (52 to 73

°

F)

: 30 minutes or more

24

°

C or more (75

°

F or more)

: 15 minutes or more

DOOR SASH MOLDING

EXT-39

< REMOVAL AND INSTALLATION >

C

D

E

F

G

H

I

J

L

M

A

B

EXT

N

O

P

DOOR SASH MOLDING

Exploded View

INFOID:0000000005248879

Removal and Installation

INFOID:0000000005248880

REMOVAL

FRONT DOOR SASH MOLDING

1.

Remove front door sash inner cover. Refer to 

INT-11, "Exploded View"

.

2.

Remove door mirror assembly. Refer to 

MIR-78, "DOOR MIRROR ASSEMBLY : Removal and Installa-

tion"

1.

Front door sash molding

2.

Front door sash outer cover

3.

Rear door sash outer cover front

4.

Rear door sash molding

5.

Rear door sash outer cover rear

6.

Double-faced adhesive tape

7.

EPT sealer

8.

Front door panel

9.

Rear door panel

Refer to 

GI-4, "Components"

 for symbols in the figure.

JMKIA2740ZZ

EXT-40

< REMOVAL AND INSTALLATION >

DOOR SASH MOLDING

3.

Remove front door sash molding mounting screw (A).

4.

Release front door weather-strip and glass run rubber.

5.

Twist and push to upper side, and then remove front door sash
molding (1).

REAR DOOR SASH MOLDING

1.

Remove rear door sash molding mounting screw (A) from front
end.

2.

Remove rear door sash molding mounting screw (A) from rear
end.

3.

Release rear door weather-strip and glass run rubber.

JMKIA2741ZZ

JMKIA2742ZZ

JMKIA2743ZZ

JMKIA2744ZZ

DOOR SASH MOLDING

EXT-41

< REMOVAL AND INSTALLATION >

C

D

E

F

G

H

I

J

L

M

A

B

EXT

N

O

P

4.

Twist and push to upper side, and then remove rear door sash
molding (1).

FRONT DOOR SASH OUTER COVER

1.

Remove front door outside molding. Refer to 

EXT-43, "Removal and Installation"

.

2.

Remove front door sash outer cover mounting screw (A) and clip
(B).

3.

Release front door sash outer cover connection between front
door panel and cover (1), with a remover tool (A) and cutter knife
(B), and take off double-faced adhesive tape.

CAUTION:

Never use an item as a remover tool that could damage
door panel.

REAR DOOR SASH OUTER COVER FRONT

1.

Remove rear door outside molding. Refer to 

EXT-43, "Removal and Installation"

.

2.

Remove rear door sash outer cover front mounting screw (A).

3.

Release rear door sash outer cover front connection between
rear door panel and cover, with a cutter knife (B), and take off
double-faced adhesive tape.

CAUTION:

Never use an item as a remover tool that could damage
door panel.

REAR DOOR SASH OUTER COVER REAR

1.

Remove rear door outside molding. Refer to 

EXT-43, "Removal and Installation"

.

JMKIA2745ZZ

JMKIA2746ZZ

JMKIA2034ZZ

JMKIA2750ZZ