Infiniti FX35, FX50 (S51). Manual - part 4

 

  Index      Infiniti     Infiniti FX35, FX50 (S51) - service repair manual 2010 year

 

Search            

 

 

 

 

 

 

 

 

 

Content   ..  1  2  3  4  5  ..

 

 

Infiniti FX35, FX50 (S51). Manual - part 4

 

 

ADP-8

< BASIC INSPECTION >

INSPECTION AND ADJUSTMENT

INSPECTION AND ADJUSTMENT

ADDITIONAL SERVICE WHEN REMOVING BATTERY NEGATIVE TERMINAL

ADDITIONAL SERVICE WHEN REMOVING BATTERY NEGATIVE TERMINAL : De-
scription

INFOID:0000000005249613

Each function is reset to the following condition when the battery terminal is disconnected.

*1

: Default value is 40mm.

NOTE:
Notice that disconnecting the battery when detected DTC are present will erase the DTC memory.

ADDITIONAL SERVICE WHEN REMOVING BATTERY NEGATIVE TERMINAL : Spe-
cial Repair Requirement

INFOID:0000000005249614

1.

SYSTEM INITIALIZATION

Perform system initialization. Refer to 

ADP-9, "SYSTEM INITIALIZATION : Description"

.

>> GO TO 2.

2.

SYSTEM SETTING

Perform system setting. Refer to 

ADP-11, "SYSTEM SETTING : Description"

.

>> GO TO 3.

3.

MEMORY STORAGE

Perform memory storage. Refer to 

ADP-9, "MEMORY STORING : Description"

.

>> END

ADDITIONAL SERVICE WHEN REPLACING CONTROL UNIT

ADDITIONAL SERVICE WHEN REPLACING CONTROL UNIT : Description

INFOID:0000000005249615

Each function is reset to the following condition when the driver seat control unit is replaced.

*1

: Default value is 40mm.

NOTE:
Notice that disconnecting the battery when detected DTC are present will erase the DTC memory.

ADDITIONAL SERVICE WHEN REPLACING CONTROL UNIT : Special Repair Re-

Function

Condition

Procedure

Memory (Seat, steering, mirror)

Erased

Perform storing

Entry/exit assist

OFF

Perform initialization

Set slide amount

*1

Intelligent Key interlock

Erased

Perform storing

Seat synchronization

OFF

Function

Condition

Procedure

Memory (Seat, steering, mirror)

Erased

Perform storing

Entry/exit assist

OFF

Perform initialization

Set slide amount

*1

Intelligent Key interlock

Erased

Perform storing

Seat synchronization

OFF

INSPECTION AND ADJUSTMENT

ADP-9

< BASIC INSPECTION >

C

D

E

F

G

H

I

K

L

M

A

B

ADP

N

O

P

quirement

INFOID:0000000005249616

1.

SYSTEM INITIALIZATION

Perform system initialization. Refer to 

ADP-9, "SYSTEM INITIALIZATION : Description"

.

>> GO TO 2.

2.

SYSTEM SETTING

Perform system setting. Refer to 

ADP-11, "SYSTEM SETTING : Description"

.

>> GO TO 3.

3.

MEMORY STORAGE

Perform memory storage. Refer to 

ADP-9, "MEMORY STORING : Description"

.

>> END

SYSTEM INITIALIZATION

SYSTEM INITIALIZATION : Description

INFOID:0000000005249617

Always perform the initialization when the battery terminal is disconnected or the driver seat control unit is
replaced.
The entry/exit assist function will not operate normally if no initialization is performed. 

SYSTEM INITIALIZATION : Special Repair Requirement

INFOID:0000000005249618

INITIALIZATION PROCEDURE

1.

 CHOOSE METHOD

There are two initialization methods.

Which method do you use?

With door switch>>GO TO 2.
With vehicle speed>>GO TO 4.

2.

 STEP A-1

Turn ignition switch from ACC to OFF position. 

>> GO TO 3.

3.

 STEP A-2

Driver door switch is ON (open) 

 OFF (close) 

 ON (open).

>> END

4.

 STEP B-1

Drive the vehicle at more than 25 km/h (16 MPH). 

>> END

MEMORY STORING

MEMORY STORING : Description

INFOID:0000000005249619

Always perform the memory storage when the battery terminal is disconnected or the driver seat control unit is
replaced. The memory function and Intelligent Key interlock function will not operate normally if no memory
storage is performed. 

ADP-10

< BASIC INSPECTION >

INSPECTION AND ADJUSTMENT

MEMORY STORING : Special Repair Requirement

INFOID:0000000005249620

Memory Storage Procedure

Two positions for the driver seat, steering column and outside mirror can be stored for memory operation by
following procedure.

1.

STEP 1

Shift A/T selector lever to P position.

>> GO TO 2.

2.

STEP 2

Turn ignition switch ON.

>> GO TO 3.

3.

STEP 3

Adjust driver seat, steering column and outside mirror position manually.

>> GO TO 4.

4.

STEP 4

1.

Push set switch.
NOTE:
• Memory indicator for which driver seat position is already retained in memory is illuminated for 5 sec-

onds.

• Memory indicator for which driver seat position is not retained in memory is illuminated for 0.5 second.

2.

Push the memory switch  (1 or 2) for at least 1 second within 5 seconds after pushing the set switch.
NOTE:
• To enter driver seat positions into blank memory, memory indicator will be turned on  for 5 seconds.
• To modify driver seat positions, memory indicator will be turned OFF for 0.5 second, then turned ON for

5 seconds.

NOTE:
If memory is stored in the same memory switch, the previous memory will be deleted.

Do you need linking of Intelligent Key?

YES

>> GO TO 6.

NO

>> GO TO 5.

5.

STEP 5

Confirm the operation of each part with memory operation.

>> END

6.

STEP 6

Push the Intelligent Key unlock button within 5 seconds after pushing memory switch (while the memory indi-
cator is turned ON).

>> GO TO 7.

7.

STEP 7

Confirm the operation of each part with memory operation and Intelligent Key interlock operation.

>> END

SYSTEM SETTING

INSPECTION AND ADJUSTMENT

ADP-11

< BASIC INSPECTION >

C

D

E

F

G

H

I

K

L

M

A

B

ADP

N

O

P

SYSTEM SETTING : Description

INFOID:0000000005249621

The settings of the automatic driving positioner system can be changed, using CONSULT-III, the display unit
in the center of the instrument panel and the set switch. Always check the settings before and after discon-
necting the battery terminal or replacing driver seat control unit.

Setting Change

×

: Applicable

SYSTEM SETTING : Special Repair Requirement

INFOID:0000000005249622

1.

 CHOOSE METHOD

There are three way of setting method.

Which method do you choose?

With display>>GO TO 2.
With set switch>>GO TO 4.
With CONSULT-III>>GO TO 6.

2.

 WITH DISPLAY - STEP 1

Turn ignition switch ON.

>> GO TO 3.

3.

 WITH DISPLAY - STEP 2

1.

Push “SETTING” button.

2.

Select “Comfort & convenience”.

3.

Select “Lift Steering Wheel ON Exit”or “Slide Driver

s Seat Back ON Exit” on display, then push

-

Lift Steering Wheel ON Exit: Entry/exit assist (steering column)

-

Slide Driver's Seat Back On Exit: Entry/exit assist (seat)

>> END

4.

 WITH SET SWITCH - STEP 1

1.

Turm ignition switch OFF.

2.

Push setting button and hold for more than 10 seconds, then confirm blinking of the memory switch indi-
cator.

• Entry/exit assist (seat/steering column)  are ON: Memory switch indicator blink two times. 
• Entry/exit assist (seat/steering column)  are OFF: Memory switch indicator blink once.

>> GO TO 5.

5.

 WITH SET SWITCH - STEP 2

1.

Turm ignition switch ACC

Item

Content

CON-

SULT

–III

Display

Set 

switch

Factory 

setting

Amount of seat sliding for
entry/exit assist

The amount of seat sliding for entry/exit assist can 
be selected from 3 items.
[40mm/80mm/150mm]

x

40mm

Entry/exit assist
(seat)

Entry/exit assist (seat) can be selected: 
ON (operated) – OFF (not operated)

x

x

x

ON

Entry/exit assist
(steering column)

Entry/exit assist (steering column) can be selected: 
ON (operated) – OFF (not operated)

x

x

ON

Seat synchronization

Seat synchronization can be selected: ON (operat-
ed) – OFF (not operated)

x

OFF

Reset custom settings

All settings can be set to default (factory setting).

x

 

 

 

 

 

 

 

 

 

 

Content   ..  1  2  3  4  5  ..