2. Turn ignition switch to OFF position. Disable air bag system. See DISABLING SYSTEM under
DISABLING & ACTIVATING AIR BAG SYSTEM. Disconnect driver-side air bag connector from
upper cable reel connector. See Fig. 4 . Connect SRS Simulator Lead (07XAZ-SZ30100) and SRS
Inflator Simulator (07SAZ-TB4011A) to upper cable reel connector. Reconnect negative battery cable.
Erase DTC memory. Retrieve DTC. See RETRIEVING DIAGNOSTIC TROUBLE CODE (DTC)
under DIAGNOSTICS. If DTC 11-8 or 11-A is indicated, go to next step. If DTC 11-8 or 11-A is not
indicated, replace driver-side air bag module. See DRIVER-SIDE AIR BAG MODULE under
REMOVAL & INSTALLATION.
3. Turn ignition switch to OFF position. Disable air bag system. Disconnect dashboard wire harness
connector from lower cable reel connector. Connect SRS simulator lead and SRS inflator simulator to
dashboard wire harness connector. Reconnect negative battery cable. Erase DTC memory. Retrieve DTC.
If DTC 11-8 or 11-A is indicated, go to next step. If DTC 11-8 or 11-A is not indicated, replace cable
reel. See CABLE REEL under REMOVAL & INSTALLATION.
4. Turn ignition switch to OFF position. Disable air bag system. Access and disconnect SRS unit connector
"A". See SRS UNIT under REMOVAL & INSTALLATION. See Fig. 33 . Reconnect negative battery
cable. Turn ignition switch to ON position. Disconnect SRS inflator simulator from SRS simulator lead.
DO NOT disconnect simulator lead from dashboard wire harness connector. Measure voltage between
ground and each SRS inflator simulator connector terminal. If voltage is less than 0.5 volt at all terminals,
replace SRS unit. If voltage is more than 0.5 volt at any terminal, replace dashboard wire harness.
DTC 11-9, 11-B
1. Before proceeding, see AIR BAG SAFETY PRECAUTIONS . Erase Diagnostic Trouble Code (DTC)
memory. See ERASING DIAGNOSTIC TROUBLE CODE MEMORY under DIAGNOSTICS. Turn
ignition switch to ON position. If AIR BAG warning light stays on, go to next step. If AIR BAG warning
light goes off after about 6 seconds, system is okay at this time. Check for intermittent malfunction. See
TROUBLESHOOTING INTERMITTENT FAILURES under DIAGNOSTICS.
2. Turn ignition switch to OFF position. Disable air bag system. See DISABLING SYSTEM under
DISABLING & ACTIVATING AIR BAG SYSTEM. Disconnect driver-side air bag connector from
upper cable reel connector. See Fig. 4 . Connect SRS Simulator Lead (07XAZ-SZ30100) and SRS
Inflator Simulator (07SAZ-TB4011A) to upper cable reel connector. Reconnect negative battery cable.
Erase DTC memory. Retrieve DTC. See RETRIEVING DIAGNOSTIC TROUBLE CODE (DTC)
under DIAGNOSTICS. If DTC 11-9 or 11-B is indicated, go to next step. If DTC 11-9 or 11-B is not
indicated, replace driver-side air bag module. See DRIVER-SIDE AIR BAG MODULE under
REMOVAL & INSTALLATION.
3. Turn ignition switch to OFF position. Disable air bag system. Disconnect dashboard wire harness
connector from lower cable reel connector. Connect SRS simulator lead and SRS inflator simulator to
dashboard wire harness connector. Reconnect negative battery cable. Erase DTC memory. Retrieve DTC.
If DTC 11-9 or 11-B is indicated, go to next step. If DTC 11-9 or 11-B is not indicated, replace cable reel.
See CABLE REEL under REMOVAL & INSTALLATION.
4. Disable air bag system. Access and disconnect SRS unit connector "A". See SRS UNIT under
REMOVAL & INSTALLATION. See Fig. 33 . Disconnect SRS inflator simulator from SRS inflator
simulator lead. DO NOT disconnect simulator lead from dashboard wire harness connector. Measure
resistance between ground and each SRS inflator simulator connector terminal. If resistance is more than
one megohm at all terminals, replace SRS unit. If resistance is less than one megohm at any terminal,
replace dashboard wire harness.
2004 Acura TSX
2004 ACCESSORIES/SAFETY EQUIPMENT Acura - Air Bag Restraint Systems