Acura TSX / Honda Accord CL. Manual - part 152

 

  Index      Acura     Acura TSX 2004-2008 / Honda Accord CL 2006-2008 - service repair manual

 

Search            copyright infringement  

 

 

 

 

 

 

 



 

 

Content   ..  150  151  152  153   ..

 

 

Acura TSX / Honda Accord CL. Manual - part 152

 

 

Fig. 39: Multiplex Integrated Control System Wiring Diagram (2 Of 2) 

DTC TROUBLESHOOTING 

DTC B1000: COMMUNICATION BUS LINE ERROR 

1. Clear the DTCs using the HDS.  

2. Cycle the ignition switch to OFF and then back ON. 

 

2004 Acura TSX 

2004 ACCESSORIES & EQUIPMENT Multiplex Integrated Control System - TSX

  

 

3. Check for DTCs using the HDS. 

Is DTC B1000 indicated? 

YES: Go to step 4.  

NO: Intermittent failure. The communication bus line is OK at this time. Check for loose or 
poor connections. If the connections are good, check the battery condition and the charging 
system. See GENERATORS & REGULATORS .  

4. Check for DTCs using the HDS. 

Are DTC B1005, B1006, B1007, B1008, B1009 and B1010 indicated? 

YES: Go to step 5.  

NO: Replace the MICU.  

5. Disconnect each control unit one at a time. Clear the DTC, then recheck for DTCs after each unit is 

disconnected. 

z

Gauge control module  

z

Relay control module  

z

Driver's multiplex control unit  

z

Climate control unit  

z

Combination switch control unit 

Is DTC B1000 indicated with each unit disconnected? 

YES: Check for a short to power or ground in the communication circuit by 
disconnecting the harness at each control unit and testing for continuity to ground or 
short to power. Repair or replace the harness as necessary.  

NO: Replace the control unit that was disconnected, and did not set DTC B1000.  

DTC B1050, B1100, B1150, B1200, B1250: COMMUNICATION BUS LINE ERROR 

1. Clear the DTCs using the HDS.  

2. Cycle the ignition switch to OFF and then back ON.  

3. Check for DTCs using the HDS. 

Are DTC(s) B1050, B1100, B1150, B1200 or B1250 indicated? 

YES: Go to step 4.  

NO: Intermittent failure, the system is OK at this time. 

 

2004 Acura TSX 

2004 ACCESSORIES & EQUIPMENT Multiplex Integrated Control System - TSX

  

 

Fig. 40: DTC Table 

4. Check for DTCs using the HDS. 

Is DTC(s) B1000 indicated? 

YES: Troubleshoot DTC B1000.  

NO: If DTC B1050 is indicated, replace the relay control module. If DTC B1100 is 
indicated, replace the door multiplex control unit. If DTC B1150 is indicated, replace the 
gauge control module (see GAUGE CONTROL MODULE REPLACEMENT ). If DTC 
B1200 is indicated, replace the climate control unit. If DTC B1250 is indicated, replace the 
combination switch control unit.  

DTC B1001, B1002: MULTIPLEX INTEGRATED CONTROL UNIT (MICU) INTERNAL ERROR 

1. Clear the DTCs using the HDS.  

2. Cycle the ignition switch to OFF and then back ON.  

3. Operate the door lock (LOCK/UNLOCK).  

4. Check for DTCs using the HDS. 

Is DTC B1001 or B1002 indicated? 

YES: Faulty MICU; replace the under-dash fuse/relay box.  

NO: Intermittent failure, the MICU is OK at this time. Check for loose or poor connections. 
If the connections are good, check the battery condition and the charging system. See 
GENERATORS & REGULATORS .  

DTC B1005: MICU LOST COMMUNICATION WITH RELAY CONTROL MODULE 

1. Clear the DTCs using the HDS.  

2. Cycle the ignition switch to OFF and then back ON.  

3. Check for DTCs using the HDS. 

Is DTC B1005 indicated? 

YES: Go to step 4.  

 

2004 Acura TSX 

2004 ACCESSORIES & EQUIPMENT Multiplex Integrated Control System - TSX

  

 

NO: Intermittent failure, the relay module is OK at this time. Check for loose or poor 
connections. If the connections are good, check the battery condition and the charging 
system. See GENERATORS & REGULATORS .  

4. Check for DTCs in the gauge control module using the HDS. 

Is DTC B1158 indicated? 

YES: Go to Relay Control Module Input Test (see RELAY CONTROL MODULE INPUT 
TEST
 ).  

NO: Check for an open, or a short to power or ground in the communication circuit between 
the MICU and the relay control module. If the circuit is OK, replace the MICU. If the circuit 
is bad, repair the open, or short to power or ground.  

DTC B1006: MICU LOST COMMUNICATION WITH DOOR MULTIPLEX CONTROL UNIT DOOR 
LOCK SWITCH MESSAGE 

1. Clear the DTCs using the HDS.  

2. Cycle the ignition switch to OFF and then back ON.  

3. Check for DTCs using the HDS. 

Is DTC B1006 indicated? 

YES: Go to step 2.  

NO: Intermittent failure, the door multiplex control unit is OK at this time. Check for loose 
or poor connections. If the connections are good, check the battery condition and the 
charging system. See GENERATORS & REGULATORS .  

4. Check for DTCs in the gauge control module and relay module using the HDS. 

Is DTC B1160 and B1058 indicated? 

YES: Go to Door Multiplex Control Unit Input Test (see DOOR MULTIPLEX 
CONTROL UNIT INPUT TEST
 ).  

NO: Check for an open, or a short to power or ground in the communication circuit between 
the MICU and the door multiplex control unit. If the circuit is OK, replace the MICU. If the 
circuit is bad, repair the open, or short to power or ground.  

DTC B1007: MICU LOST COMMUNICATION WITH THE COMBINATION SWITCH CONTROL 
UNIT (HEADLIGHT SWITCH MESSAGE) 

1. Clear the DTCs using the HDS.  

2. Cycle the ignition switch to OFF and then back ON.  

3. Check for DTCs using the HDS. 

Is DTC B1007 indicated? 

YES: Go to step 4.  

NO: Intermittent failure, the MICU is OK at this time. Check for loose or poor connections. 
If the connections are good, check the battery condition and the charging system. See 
GENERATORS & REGULATORS .  

4. Check for DTCs of the gauge control module and relay control module using the HDS. 

 

2004 Acura TSX 

2004 ACCESSORIES & EQUIPMENT Multiplex Integrated Control System - TSX

  

 

 

 

 

 

 

 

 

Content   ..  150  151  152  153   ..