Mazda engine L8, LF, L3. Manual - part 16

 

  Index      Mazda     Mazda engine L8, LF, L3 - service manual 2002 year

 

Search            

 

 

 

 

 

 

 

  

 

Content   ..  14  15  16  17   ..

 

 

Mazda engine L8, LF, L3. Manual - part 16

 

 

B–44

ENGINE 

Front Oil Seal Aassembly Note

1. Apply clean engine oil to the oil seal.
2. Push the oil seal slightly in by hand.
3. Compress the oil seal using the SST and a 

hammer.

Engine Front Cover Aassembly Note

1. Apply silicone sealant to the engine front cover as 

shown.

Caution

••••

Install the cylinder head cover within 10 
minutes of applying the silicone sealant.

••••

Silicone sealant is not need in area C as 
indicated below due to an existing. (L3  
(with variable valve timing mechanism))

Thickness

 A: 2.0—3.0 mm {0.079—0.118 in}
 B: 1.5—2.5 mm {0.059—0.098 in}

AME2224E331

AME2224E332

AME2224E333

ENGINE 

B–45

B

2. Install the cylinder head cover bolts in the order 

as shown.

Crankshaft Pulley Lock Bolt Aassembly Note

1. Install the SST to the camshaft as shown.

Europe

Except Europe

2. Install the M6 x 1.0 bolt in by hand.
3. Turn the crankshaft clockwise so that the 

crankshaft is in the No.1 cylinder TDC position.

Bolt No.

Tigtining torque N·m {kgf·m, ft·lbf}

1—18

8.0—11.5 N·m
{81.6—117.2 kgf·cm, 70.9—101.7 in·lbf}

19—22

40—55 {4.1—5.6, 29.7—40.5}

AME2224E334

AME2224E329

AME2224E328

AME2224E009

B–46

ENGINE 

4. Hold the crankshaft pully using the SST.
5. Tighten the crankshaft pulley lock bolt in the 

following two steps.
(1) Tighten to 96—104 N·m {9.8—10.6 kgf·m, 

70.9—76.7 ft·lbf}

(2) Tighten 87

°°°°

—93

°°°°

 .

6. Remove the M6 x 1.0 bolt.
7. Remove the SST from the camshaft.
8. Remove the SST from the block lower blind plug.
9. Rotate the crankshaft clockwise two turns until 

the TDC position.

•

If not aligned, loosen the crankshaft pulley 
lock bolt and repeat from Step 1.

10. Install the cylinder block lower blind plug.

Tightening torque: 20 N·m {2.0 kgf·m, 14.8 ft·lbf}

Cylinder Head Cover Aassembly Note

1. Apply silicone sealant to the mating faces as 

shown.

Caution

••••

Install the cylinder head cover within 10 
minutes of applying the silicone sealant.

Dot diameter: 4.0—6.0 mm {0.16—0.23 in}

2. Install the cylinder head cover with a new gasket.

3. Tighten the bolts in the order shown.

Tightening torque: 8.0 —12 N·m {81.6—122.3 
kgf·cm, 70.9—106.2 in·lbf}

End Of Sie

AME2224E015

AME2224E335

AME2224E336

 

 

 

 

 

 

 

Content   ..  14  15  16  17   ..