Land Rover Engine 1.8 Litre K Series. Manual - part 4

 

  Index      Land Rover     Land Rover Engine 1.8 Litre K Series - service manual 2000 year

 

Search            

 

 

 

 

 

 

 

 

 

Content   ..  1  2  3  4  5  ..

 

 

Land Rover Engine 1.8 Litre K Series. Manual - part 4

 

 

ENGINE

2

OVERHAUL

3. Rotate crankshaft to align camshaft gear timing

marks 90

°

BTDC.

CAUTION: Do not use timing gears, gear
retaining bolts or timing belt to rotate
crankshaft.

4. Fit camshaft gear locking tool LRT-12-134.

5. Check that timing mark on crankshaft pulley is

aligned with mark on timing belt lower cover.

6. Fit flywheel locking tool LRT-12-145 .
7. Secure with 2 bolts.

8. Remove crankshaft pulley bolt and washer.
9. Remove crankshaft pulley.

10. Remove 3 bolts securing timing belt lower

cover.

11. Remove timing belt lower cover together vwith

seals.

ENGINE

OVERHAUL

3

12. Slacken tensioner pulley Allen screw.
13. Slacken tensioner backplate screw.
14. Push tensioner pulley down to fully OFF

position.

NOTE: Tensioner spring and pillar bolt are
only fitted for tensioning replacement
timing belts.

15. Tighten backplate screw to 10 Nm.
16. Ease timing belt from gears using the fingers

only.

17. Discard timing belt.

CAUTION: Timing belt must always be
replaced during engine overhaul. Do not
rotate camshafts or crankshaft with timing

belt removed and cylinder head fitted.

Camshaft timing belt - manual tensioner refit

CAUTION: When a replacement timing belt
is to be fitted, it will be necessary to fit the
tensioner spring and pillar bolt supplied

with the replacement belt to adjust belt tension.

1. Clean timing gears, coolant pump drive gear

and tensioner pulley.

CAUTION: If the sintered gears have been
subjected to prolonged oil contamination,
they must be soaked in a solvent bath and

then thoroughly washed in clean solvent before
refitting. Because of the porous construction of
sintered material, oil impregnated in the gears
will emerge and contaminate the belt.

2. Check correct alignment of camshaft gear

timing marks, fit camshaft gear locking tool
LRT-12-134.

ENGINE

4

OVERHAUL

3. Check that crankshaft gear timing marks are

aligned with flange on oil pump - 90

°

BTDC.

4. Fit flywheel locking tool LRT-12-145, secure

with 2 bolts.

5. Fit tensioner spring and pillar bolt supplied with

replacement timing belt. Connect spring to
tensioner backplate and pillar bolt.

6. Slacken tensioner backplate screw, ensure

tensioner moves fully through its adjustment
range and returns under spring tension.

7. Push tensioner down to fully OFF position and

tighten tensioner backplate screw to 10 Nm.

8. Using the fingers only, fit a new timing belt over

crankshaft timing gear and then over camshaft
gears keeping belt taut between crankshaft
timing gear and exhaust camshaft gear.

9. Ease timing belt over tensioner pulley and

coolant pump drive gear.

10. Ensure belt is positioned centrally on gears

and pulley.

11. Ensure inserts are fitted in timing belt lower

cover.

12. Fit timing belt lower cover, ensuring correct

position of seals; fit lower cover screws and
tighten to 9 Nm.

ENGINE

OVERHAUL

5

13. Fit crankshaft pulley to crankshaft timing gear

ensuring that indent on pulley locates over lug
on gear.

14. Secure with crankshaft pulley bolt and washer,

tighten bolt to 205 Nm.

15. Remove camshaft and flywheel locking tools.

16. Slacken tensioner backplate screw and tension

timing belt by applying finger pressure to
tensioner backplate.

17. With tensioner pulley against timing belt and

backplate held in position, tighten backplate
screw to 10 Nm.

18. Rotate crankshaft 2 complete revolutions

clockwise and align camshaft gear timing
marks.

CAUTION: Do not use camshaft timing
gears, gear retaining bolts or timing belt to
rotate crankshaft.

19. Slacken tensioner backplate screw and check

that belt is being tensioned by the tensioner
spring.

20. Tighten tensioner backplate screw to 10 Nm

and tensioner pulley Allen screw to 45 Nm.

21. Disconnect tensioner spring from pillar bolt,

release spring from tensioner, remove and
discard spring.

22. Remove and discard pillar bolt.

 

 

 

 

 

 

 

 

 

 

Content   ..  1  2  3  4  5  ..