Land Rover Engine 2.0 Litre T Series. Manual - part 15

 

  Index      Land Rover     Land Rover 2.0 Litre T Series Engine - service manual 1997 year

 

Search            

 

 

 

 

 

 

 

 

 

Content   ..  13  14  15 

 

 

 

Land Rover Engine 2.0 Litre T Series. Manual - part 15

 

 

ENGINE

OVERHAUL

45

Crankshaft - refit

1. Lubricate new main bearing shells with engine

oil and fit to cylinder block and main bearing
caps.

NOTE: Front, centre and rear main bearing
shells have an oil groove, intermediate
main bearing shells are plain.

2. Lubricate thrust washer halves with engine oil

and fit to cylinder block and centre main
bearing cap with the oil grooves facing away
from the cap.

NOTE: The two tagged thrust washers are
fitted in main bearing cap.

3. Lubricate crankshaft journals with engine oil

and using assistance, position crankshaft in
cylinder block.

4. Fit main bearing caps and shells.

NOTE: Bearing caps are numbered from 1
to 5 with Number 1 bearing cap being
nearest to front of cylinder block Ensure

arrows on bearing caps point towards front.

5. Lightly oil main bearing cap bolts.
6. Fit main bearing cap bolts in their original fitted

order and starting from centre main bearing
cap and working outwards, tighten bolts
progressively to 110 Nm.

7. Fit 2 Woodruff keys in crankshaft.
8. Fit big-end bearings.

ENGINE

46

OVERHAUL

Big-end bearings - refit

1. Temporarily fit timing gear, crankshaft pulley

and holding tool LRT-12-059 to crankshaft.

2. Use 2 pulley bolts to retain tool.
3. Lubricate new big-end bearing shells and

crankshaft journals with engine oil.

4. Rotate crankshaft to bring numbers 2 and 3

big-end journals to BDC, pull connecting rods
on to journals and remove plastic sleeving from
bolts.

CAUTION: Do not rotate crankshaft more
than 45

°

in any direction.

5. Fit big-end bearing caps and shells to their

respective connecting rods ensuring that
reference marks are aligned.

6. Fit and tighten big-end bearing cap nuts to 55

Nm.

CAUTION: Ensure nuts are fitted in their
original locations.

7. Repeat above procedures for numbers 1 and 4

big-end bearings.

8. Remove holding tool LRT-12-059.

ENGINE

OVERHAUL

47

Gearbox adaptor plate - refit

1. Position gearbox adaptor plate on locating

dowels.

2. Fit 4 Torx screws and tighten to 45 Nm.
3. Fit 2 bolts and tighten to 90 Nm.

Crankshaft rear oil seal - refit

1. Remove all traces of oil from oil seal running

surface on crankshaft and tool LRT-12-061.

2. Check that oil seal bolt holes in cylinder block

are clean and dry.

3. Position tool LRT-12-061 on crankshaft.

NOTE: If oil seal protector is supplied with
new oil seal, this should be used as an
alternative to LRT-12-061.

4. Taking care not to touch sealing lip of oil seal,

slide seal and housing on to crankshaft.

CAUTION: Do not lubricate oil seal or
running surface on crankshaft.

5. Position oil seal and housing on cylinder block.
6. Fit bolts and working in sequence shown,

tighten to 8 Nm.

7. Remove tool LRT-12-061 or oil seal protection

sleeve.

ENGINE

DATA, TORQUE & TOOLS

1

DATA

Oil pump
Outer rotor to body clearance

0.05 to 0.10 mm

. . . . . . . . . . . . . . . . . .

Inner rotor tip clearance

0.025 to 0.12 mm

. . . . . . . . . . . . . . . . . . . . . . .

Outer rotor end float

0.03 to 0.08 mm

. . . . . . . . . . . . . . . . . . . . . . . . .

Oil pressure relief valve
Spring free length

38.9 mm

. . . . . . . . . . . . . . . . . . . . . . . . . . .

Camshaft
Camshaft end-float

0.06 to 0.25 mm

. . . . . . . . . . . . . . . . . . . . . . . . . .

Bearing clearance

0.060 to 0.094 mm

. . . . . . . . . . . . . . . . . . . . . . . . . . .

Service limit

0.15 mm

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Timing belt tensioner
Spring free length

57.5 to 58.5 mm

. . . . . . . . . . . . . . . . . . . . . . . . . . .

Cylinder head
Longitudinal warp - maximum

0.1 mm

. . . . . . . . . . . . . . . . . .

Transverse warp - maximum

0.1 mm

. . . . . . . . . . . . . . . . . . .

Diagonal warp - maximum

0.1 mm

. . . . . . . . . . . . . . . . . . . . .

Cylinder head height

135.0 to 135.1 mm

. . . . . . . . . . . . . . . . . . . . . . . . .

Valve springs
Free length

46.25 mm

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Fitted length

37.0 mm

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Load - valve closed

255

±

12 N

. . . . . . . . . . . . . . . . . . . . . . . . . .

Load - valve open

560

±

22.5 N

. . . . . . . . . . . . . . . . . . . . . . . . . . .

Valves
Valve stem diameter:

Inlet

7.09 to 7.10 mm

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Exhaust

7.07 to 7.09 mm

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Valve head diameter:
Inlet

31.7 to 31.95 mm

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Exhaust

29.2 to 29.43 mm

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Valve installed height - maximum

43.4 mm

. . . . . . . . . . . . . . .

Valve stem to guide clearance:
Inlet

0.04 to 0.06 mm

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Service limit

0.09 mm

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Exhaust

0.06 to 0.07 mm

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Service limit

0.10 mm

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

 

 

 

 

 

 

 

Content   ..  13  14  15