Range Rover. Manual - part 145

 

  Index      Land Rover     Range Rover P38 - service manual 1995 year

 

Search            

 

 

 

 

 

 

 

 

 

Content   ..  143  144  145  146   ..

 

 

Range Rover. Manual - part 145

 

 

TRANSFER BOX

11

DESCRIPTION AND OPERATION

Pin No.

Description

Input/Output

26

Motor drive - Clockwise

Output

27

Not used

-

28

Transfer box OBDII link

Output

29

Power earth

Input

30

Vehicle speed signal earth

Input

31

Motor position switch 3

Input

32

Motor switch position 2

Input

33

High/Low range select

Input

34

Park/Neutral (Auto) Neutral (Manual) Signal

Input

35

High range status line

Output

36

Neutral range status line

Output

41

TRANSFER BOX

NEW RANGE ROVER

12

DESCRIPTION AND OPERATION

TRANSFER BOX - OPERATION

Transfer Box

Drive is transmitted to the transfer box from the
gearbox output shaft which is permanently engaged in
the sun gear of the epicyclic gear set. In high range
the sun gear transmits drive directly to the selector
sleeve. In low range, when the selector spool has
moved the selector sleeve, the sun gear transmits
drive through the planet carrier.

The rotation of the selector sleeve is transferred to the
intermediate shaft. A gear attached to the
intermediate shaft carries the morse chain which
transfers the drive to the differential unit.

The rear output shaft passes through the differential
unit and rotates at the same speed. The viscous
coupling passes drive from the rear output shaft to the
front output shaft. When the silicon fluid in the viscous
coupling becomes warm its resistance to shear
increases passing more drive to the front drive shaft
increasing traction.

Electrical Operation

Range change

NOTE: Range changes should be
performed with the vehicle stationary and
although range changes are possible at

very low speeds, this practice is not
recommended.

Automatic transmission

To change range the vehicle speed must be reduced
to below 5 mph (8 km/h). Move the gear selector to
neutral and then across the H-gate into the neutral
position in the selected range. The appropriate LED
illuminations on the selected range side of the selector
cover will flash and an audible warning will sound. The
flashing LED’s and the audible warning will continue
while the ratio control motor is moving the transfer box
to the selected range.

When the ratio control motor has moved the transfer
box into the selected range the LED’s will stop
flashing, the audible warning will stop and a message
is displayed in the message centre. The desired gear
can be selected and the vehicle can be driven as
required.

If the vehicle is moving above 5 mph (8 km/h) or the
selector lever is moved into gear before the range
change is complete, the change will not occur and a
’SLOW DOWN’ or ’SELECT NEUTRAL’ message will
be displayed in the message centre.

NOTE: The ’SLOW DOWN’ message is
generated by the BeCM, not the transfer
box ECU.

The transfer box can be placed in the ’Neutral’
position by moving the selector lever into the ’PARK’
position. Insert a spare fuse (minimum 5 Amp) into
fuse position 11 on the BeCM. After 5 seconds the
transfer box moves to the neutral position, an audible
warning will sound, a ’TRANSFER NEUTRAL’
message is displayed in the message centre and the
high and low LED illumination on the selector cover
will extinguish.

Manual transmission

To change from high to low the vehicle speed must be
below 5 mph (8 km/h) or from low to high the vehicle
speed must be below 15 mph (24 Km/h).

Select neutral with the gear lever and press the
high/low switch on the fascia. The indicator lamp on
the switch will flash as the range change takes place.
If the change is from high to low the lamp will
continuously illuminate when the change is
successfully completed. If the change is from low to
high the lamp will extinguish when the change is
complete. The message centre displays the selected
range.

If a range change is requested and the vehicle is
moving too fast or neutral has not been selected, the
indicator lamp on the switch will flash and a ’SLOW
DOWN’ or ’SELECT NEUTRAL’ message will appear
in the message centre.

NOTE: The ’SLOW DOWN’ message is
generated by the BeCM, not the transfer
box ECU.

The transfer box can be placed in the ’Neutral’
position by placing the gear lever in neutral and
inserting a spare fuse (minimum 5 Amp) into fuse
position 11 on the BeCM. After 5 seconds the transfer
box moves to neutral, an audible warning will sound
and a ’TRANSFER NEUTRAL’ message is displayed
in the message centre.

TRANSFER BOX

13

DESCRIPTION AND OPERATION

Range information - Automatic transmission

High range

When the transfer box is in high range the message
centre only displays the selected gear and the high
range side of the selector lever cover is illuminated in
green.

High to low range

When a change from high to low range is requested:

The low range selector cover LED’s flash in
orange

The high range selector cover LED’s remain
illuminated in green

The transfer box amber warning lamp in the
instrument pack flashes while the range change
is taking place.

When the range change is complete:

The low range selector cover LED’s are
continuously illuminated in orange

The high range selector cover green LED
illumination goes off

The transfer box warning lamp goes off

The message centre displays ’LOW’ and after
several seconds displays ’L’ in front of the
selected gear.

Low to high range

When a change from low to high range is requested:

The high range selector cover LED’s flash in
green

The low range selector cover LED’s remain
illuminated in orange

The transfer box warning lamp in the instrument
pack flashes while the range change is taking
place.

When the range change is complete:

The high range selector cover LED’s are
continuously illuminated in green

The low range selector cover orange LED
illumination goes off

The transfer box warning lamp goes off

The message centre displays ’HIGH’ for several
seconds, then ’HIGH’ is removed and only the
selected gear is displayed.

Range selection parameters incorrect

If a range change is requested and the vehicle speed
is too high:

The LED illumination on the selected side of the
cover will flash

A ’SLOW DOWN’ message is displayed in the
message centre

The transfer box warning lamp in the instrument
pack flashes.

If a range change is requested and the selector lever
is moved before the range change is complete:

The LED illumination on the selected side of the
cover will flash

A ’SELECT NEUTRAL’ message is displayed in
the message centre

The BeCM will initiate an audible warning

The transfer box warning lamp in the instrument
pack flashes.

Transfer box to neutral

When a spare fuse (5 Amp minimum) is inserted in
BeCM fuse position 11 to select transfer box neutral:

A five second delay is initiated before the
transfer box moves to neutral

The BeCM initiates an audible warning

A ’TRANSFER NEUTRAL’ message is displayed
in the message centre.

41

TRANSFER BOX

NEW RANGE ROVER

14

DESCRIPTION AND OPERATION

Range information - Manual transmission

High range

When the transfer box is in high range, the message
centre does not display any transmission information
and the high/low request switch indicator lamp is off.

High to low range

When a change from high to low is requested:

The high/low switch indicator lamp flashes

The transfer box warning lamp in the instrument
pack flashes.

When the range change is complete:

The high/low switch indicator lamp is illuminated
continuously

The transfer box warning lamp goes off

A ’LOW’ message is continuously displayed in
the message centre.

Low to high range

When a change from low to high range is requested:

The high/low switch indicator lamp flashes

The transfer box warning lamp in the instrument
pack flashes.

When the range change is complete:

The high/low switch indicator lamp goes off

The transfer box warning lamp goes off

The message centre displays ’HIGH’ for several
seconds.

Range selection parameters incorrect

If a range change is requested and the vehicle speed
is too high:

The high/low switch indicator lamp will flash

The transfer box warning lamp in the instrument
pack will flash

A ’SLOW DOWN’ message is displayed in the
message centre.

If a range change is requested and the transmission is
in gear or a gear selected before range change is
complete:

The high/low switch indicator lamp will flash

The transfer box warning lamp in the instrument
pack will flash

A ’SELECT NEUTRAL’ message is displayed in
the message centre for several seconds. If the
vehicle remains in gear the message will not be
repeated.

Transfer box to neutral

When a spare fuse (5 Amp minimum) is inserted in
BeCM fuse position 11 to select transfer box neutral:

A five second delay is initiated before the
transfer box moves to neutral

The BeCM initiates an audible warning

A ’TRANSFER NEUTRAL’ message is displayed
in the message centre.

 

 

 

 

 

 

 

Content   ..  143  144  145  146   ..