Range Rover. Manual - part 16

 

  Index      Land Rover     Range Rover P38 - service manual 1995 year

 

Search            

 

 

 

 

 

 

 

 

 

Content   ..  14  15  16  17   ..

 

 

Range Rover. Manual - part 16

 

 

07 - GENERAL FITTING REMINDERS

CONTENTS

Page

INFORMATION

GENERAL FITTING REMINDERS

1

.......................................................................

PRECAUTIONS AGAINST DAMAGE

1

..................................................................

SAFETY PRECAUTIONS

1

....................................................................................

PREPARATION

2

....................................................................................................

DISMANTLING

2

.....................................................................................................

INSPECTION-GENERAL

2

.....................................................................................

BALL AND ROLLER BEARINGS

3

.........................................................................

OIL SEALS

4

...........................................................................................................

JOINTS AND JOINT FACES

5

................................................................................

FLEXIBLE HYDRAULIC PIPES, HOSES

5

.............................................................

FUEL SYSTEM HOSES

6

.......................................................................................

COOLING SYSTEM HOSES

6

...............................................................................

METRIC BOLT IDENTIFICATION

7

........................................................................

METRIC NUT IDENTIFICATION

8

..........................................................................

KEYS AND KEYWAYS

8

........................................................................................

TAB WASHERS

8

...................................................................................................

SPLIT PINS

8

..........................................................................................................

NUTS

9

...................................................................................................................

LOCKING WIRE

9

...................................................................................................

SCREW THREADS

9

..............................................................................................

UNIFIED THREAD IDENTIFICATION

9

..................................................................

GENERAL FITTING REMINDERS

1

INFORMATION

GENERAL FITTING REMINDERS

WORKSHOP SAFETY IS YOUR RESPONSIBILITY!

The suggestions, cautions and warnings in the
section are intended to serve as reminders for
trained and experienced mechanics. This manual
is not a course in automotive mechanics or
workshop safety.

Shop equipment, shop environment, and the use
and disposal of solvents, fluids, and chemicals
are subject to government regulations which are
intended to provide a level of safety. It is your
responsibility to know and comply with such
regulations.

PRECAUTIONS AGAINST DAMAGE

1. Always fit covers to protect wings before

commencing work in engine compartment.

2. Cover seats and carpets, wear clean overalls

and wash hands or wear gloves before working
inside vehicle.

3. Avoid spilling hydraulic fluid or battery acid on

paint work. Wash off with water immediately if
this occurs. Use Polythene sheets to protect
carpets and seats.

4. Always use a recommended Service Tool, or a

satisfactory equivalent, where specified.

5. Protect temporarily exposed screw threads by

replacing nuts or fitting plastic caps.

SAFETY PRECAUTIONS

1. Whenever possible use a ramp or pit when

working beneath vehicle, in preference to
jacking. Chock wheels as well as applying
parking brake.

WARNING: Do not use a pit when
removing fuel system components.

2. Never rely on a jack alone to support vehicle.

Use axle stands carefully placed at jacking
points to provide rigid support.

3. Ensure that a suitable form of fire extinguisher is

conveniently located.

4. Check that any lifting equipment used has

adequate capacity and is fully serviceable.

5. Disconnect negative (grounded) terminal of

vehicle battery.

WARNING: Do not disconnect any pipes in
air conditioning refrigeration system,
unless trained and instructed to do so. A

refrigerant is used which can cause blindness if
allowed to contact eyes.

6. Ensure that adequate ventilation is provided

when volatile degreasing agents are being used.

7. Do not apply heat in an attempt to free stiff nuts

or fittings; as well as causing damage to
protective coatings, there is a risk of damage to
electronic equipment and brake linings from
stray heat.

07

GENERAL FITTING REMINDERS

NEW RANGE ROVER

2

INFORMATION

PREPARATION

1. Before removing a component, clean it and its

surrounding areas as thoroughly as possible.

2. Blank off any openings exposed by component

removal, using greaseproof paper and masking
tape.

3. Immediately seal fuel, oil or hydraulic lines when

separated, using plastic caps or plugs, to
prevent loss of fluid and entry of dirt.

4. Close open ends of oilways, exposed by

component removal, with tapered hardwood
plugs or readily visible plastic plugs.

5. Immediately a component is removed, place it in

a suitable container; use a separate container for
each component and its associated parts.

6. Before dismantling a component, clean it

thoroughly with a recommended cleaning agent;
check that agent is suitable for all materials of
component.

7. Clean bench and provide marking materials,

labels, containers and locking wire before
dismantling a component.

DISMANTLING

1. Observe scrupulous cleanliness when

dismantling components, particularly when
brake, fuel or hydraulic system parts are being
worked on. A particle of dirt or a cloth fragment
could cause a dangerous malfunction if trapped
in these systems.

2. Blow out all tapped holes, crevices, oilways and

fluid passages with an air line. Ensure that any
O-rings used for sealing are correctly replaced or
renewed, if disturbed.

3. Use marking ink to identify mating parts, to

ensure correct reassembly. If a centre punch or
scriber is used they may initiate cracks or
distortion of components.

4. Wire together mating parts where necessary to

prevent accidental interchange (e.g. roller
bearing components).

5. Wire labels on to all parts which are to be

renewed, and to parts requiring further
inspection before being passed for reassembly;
place these parts in separate containers from
those containing parts for rebuild.

6. Do not discard a part due for renewal until after

comparing it with a new part, to ensure that its
correct replacement has been obtained.

INSPECTION-GENERAL

1. Never inspect a component for wear or

dimensional check unless it is absolutely clean;
a slight smear of grease can conceal an incipient
failure.

2. When a component is to be checked

dimensionally against figures quoted for it, use
correct equipment (surface plates, micrometers,
dial gauges, etc.) in serviceable condition.
Makeshift checking equipment can be
dangerous.

3. Reject a component if its dimensions are outside

limits quoted, or if damage is apparent. A part
may, however, be refitted if its critical dimension
is exactly limit size, and is otherwise satisfactory.

4. Use ’Plastigauge’ 12 Type PG-1 for checking

bearing surface clearances. Directions for its
use, and a scale giving bearing clearances in
0,0025 mm steps are provided with it.

 

 

 

 

 

 

 

Content   ..  14  15  16  17   ..