Frelander 2. Manual - part 113

 

  Index      Land Rover     Land Rover Frelander 2 - service repair manual 2006-2010 year

 

Search            

 

 

 

 

 

 

 

 

 

Content   ..  111  112  113  114   ..

 

 

Frelander 2. Manual - part 113

 

 

Parking Brake and Actuation - Parking Brake

Description and Operation

COMPONENT LOCATION

Item

Part Number

Description

1

-

Parking brake expander unit

2

-

Brake shoe retaining clip (2 off)

3

-

Parking brake outer cable sleeve

4

-

Upper (trailing) brake shoe

5

-

Brake shoe retaining spring

6

-

Brake shoe return spring

7

-

Brake shoe mechanical adjuster

8

-

Lower (leading) brake shoe

9

-

Parking brake lever cable

10

-

Parking brake cable equalizer

11

-

Parking brake inner cable

12

-

Equalizer fastener

13

-

Parking brake microswitch

14

-

Parking brake lever assembly

15

-

Parking brake outer cable

16

-

Brake dust shield

OVERVIEW

The parking brake is a manually actuated system that operates brake shoes located in the rear brake discs. The inside
center of the rear brake disc is manufactured to form the brake drum.

BRAKE SHOE ASSEMBLY

The brake shoes are mounted horizontally on an integral brake dust shield and backplate, and form an upper trailing and
lower leading brake shoe type system. Retaining pins pass through holes in the dust shield and corresponding holes in
each brake shoe bracket. Each pin is secured to the brake shoe with a retaining clip. The retaining pins allow movement of
the brake shoe toward the drum surface during parking brake operation, but prevent sideways movement of the brake shoe
away from the dust shield.

An expander unit and manual adjuster are located along the horizontal axis of the dust shield. The expander unit is
positioned at the front of the dust shield and forms the location for the leading and trailing ends of the brake shoe
brackets. The manual adjuster is mounted at the rear of the dust shield and forms the location and fulcrum point for the
opposite ends of the brake shoe brackets.

The manual adjuster provides the means to adjust the brake shoe lining to drum clearance for maintenance purposes.
Access to the manual adjuster knurled wheel is through a formed hole in the front of the brake disc. Adjustment is
required if the brake shoes or discs are renewed. A bedding-in procedure must also be performed to make sure the drum
brakes operate satisfactorily.
For additional information, refer to: 

Parking Brake Shoes Bedding-In

 (206-05 Parking Brake and Actuation, General

Procedures).

The corresponding ends of both the upper and lower brake shoe brackets are maintained in contact with the expander unit
and manual adjuster by 2 return springs. The return springs are located between the ends of each upper and lower brake
shoe and attach to holes formed in the brake shoe brackets. The return springs pull the brake shoes away from the drum
when the parking brake is released.

PARKING BRAKE LEVER

The parking brake lever is located in the floor console between the driver and passenger seats, and comprises a toothed
quadrant, pawl and press-button release mechanism. A single cable with a formed threaded rod-end connects the quadrant
to the equalizer unit, and is secured with either a locknut or a locking washer and nut.

The threaded rod allows adjustments to the parking brake cable tension and parking brake lever travel to be performed for
maintenance purposes.
For additional information, refer to: 

Parking Brake Cable Adjustment

 (206-05 Parking Brake and Actuation, General

Procedures).

The parking brake cable is routed from the parking brake lever equalizer, and along the chassis to the rear parking brake
expander unit. The parking brake cable protrudes through the brake dust shield, and is formed with a nipple that connects
to the expander unit. The opposite ends of each Left-Hand (LH) and Right-Hand (RH) parking brake cable are formed with a
nipple that connect to the equalizer unit. The equalizer unit makes sure the LH and RH parking brake assemblies operate
simultaneously when the parking brake is applied.

A microswitch is located on the base of the parking brake lever. The microswitch operates the parking brake warning
indicator lamp located in the instrument cluster, when the parking brake is applied.
For additional information, refer to: 

Instrument Cluster

 (413-01 Instrument Cluster, Description and Operation).

PRINCIPLES OF OPERATION

As the parking brake lever is applied, the toothed quadrant rotates and pulls on the threaded rod and cable equalizer. The
equalizer pulls the 2 parking brake cables and operates the 2 expander units simultaneously. Movement of the expander
unit causes the upper and lower brake shoes to pivot against the manual adjuster fulcrum, and the brake shoes contact
the brake drum against the tension of the 2 return springs.

As the parking brake lever quadrant rotates, the teeth on the pawl engage with corresponding teeth on the quadrant. In
the applied position, the pawl teeth are held under spring tension against the quadrant teeth to prevent the lever from
disengaging.

With the parking brake applied and the ignition in power mode 6 (ignition), the microswitch connects a ground to the
instrument cluster and illuminates the parking brake warning indicator lamp.
For additional information, refer to: 

Instrument Cluster

 (413-01 Instrument Cluster, Description and Operation).

When the parking brake lever press-button is pressed and the lever moved to release the parking brake, the pawl teeth
are raised clear from the quadrant teeth. As the parking brake lever is lowered, the parking brake cable closes the
expander unit and the brake shoes are immediately moved away from the brake drum by the 2 return springs.

As the parking brake lever reaches the fully released position, the microswitch is opened to disconnect the circuit to the
instrument cluster. W ith the parking brake released, the parking brake warning indicator lamp is extinguished.

1

1

1

1

Parking Brake and Actuation - Parking Brake

Diagnosis and Testing

Principle of Operation

For a detailed description of the parking brake, refer to the relevant Description and Operation section in the workshop
manual.
REFER to: 

Parking Brake

 (206-05 Parking Brake and Actuation, Description and Operation).

Inspection and Verification

1. Verify the customer concern by operating the system to duplicate the condition.

1.

2. Visually inspect for obvious signs of damage and system integrity.

2.

Visual Inspection

Mechanical

Electrical

Parking brake control
Cable and conduit
Equalizer

Parking brake control warning circuit

3. If an obvious cause for an observed or reported concern is found, correct the cause (if possible) before

proceeding to the next step.

3.

4. If the concern is not visually evident, verify the symptom and refer to the Symptom Chart.

4.

Symptom Chart

Symptom

Possible Cause

Action

The parking brake will not engage

Parking brake control
Cable and conduit

Go to Pinpoint Test A

The parking brake will not release

Cable and conduit
Parking brake control

Go to Pinpoint Test B

Pinpoint Tests

PINPOINT TEST A : THE PARKING BRAKE WILL NOT ENGAGE

TEST

CONDITIONS

DETAILS/RESULTS/ACTIONS

A1: CHECK FOR INCORRECTLY ADJUSTED REAR PARKING BRAKE CABLE

Carry out parking brake cable adjustment procedure.
REFER to: 

Parking Brake Cable Adjustment

 (206-05 Parking Brake and Actuation, General

Procedures).

Does the parking brake now engage correctly?
Yes

Vehicle OK.

No

GO to A2

.

A2: CHECK FOR WORN PARKING BRAKE SHOES

Inspect the rear parking brake shoes for excessive wear.

Are parking brake shoes OK?
Yes

GO to A3

.

No

INSTALL new parking brake shoes.
REFER to: 

Parking Brake Shoes

 (206-05 Parking Brake and Actuation, Removal and Installation).

Test the system for normal operation.

A3: CHECK FOR DAMAGED PARKING BRAKE CABLES

Inspect the parking brake components, cables and conduit for damage, rust or fraying.

Are the parking brake components, cables and conduits OK?
Yes

CHECK for other causes such as loose parking brake control or system components.

No

REPAIR or INSTALL new components, cables and conduit as necessary.
REFER to: 

Parking Brake Front Cable

 (206-05 Parking Brake and Actuation, Removal and

Installation) /

Parking Brake Rear Cables

 (206-05 Parking Brake and Actuation, Removal and Installation).

TEST the system for normal operation.

PINPOINT TEST B : THE PARKING BRAKE WILL NOT RELEASE

TEST

CONDITIONS

DETAILS/RESULTS/ACTIONS

B1: CHECK PARKING BRAKE CONTROL

• NOTE: Ensure correct adjustment of parking brake shoes prior to test.

Raise and support the vehicle with the parking brake fully applied.
REFER to: 

Lifting

 (100-02 Jacking and Lifting, Description and Operation).

 

 

 

 

 

 

 

Content   ..  111  112  113  114   ..