Frelander 2. Manual - part 21

 

  Index      Land Rover     Land Rover Frelander 2 - service repair manual 2006-2010 year

 

Search            

 

 

 

 

 

 

 

 

 

Content   ..  19  20  21  22   ..

 

 

Frelander 2. Manual - part 21

 

 

General Information - Diagnostic Trouble Code (DTC) IndexDTC:
Driver/Passenger Door Module (DDM/PDM)

Description and Operation

• NOTE: If a control module or component is suspect and the vehicle remains under manufacturer warranty, refer to the
Warranty Policy and Procedures manual (section B1.2), or determine if any prior approval program is in operation, before
the replacement of a component.

• NOTE: Generic scan tools may not read the codes listed, or may read only 5-digit codes. Match the 5 digits from the scan
tool to the first 5 digits of the 7-digit code listed to identify the fault (the last 2 digits give extra information read by the
manufacturer-approved diagnostic system).

• NOTE: When performing voltage or resistance tests, always use a digital multimeter (DMM) accurate to three decimal
places, and with an up-to-date calibration certificate. W hen testing resistance always take the resistance of the DMM
leads into account.

• NOTE: Check and rectify basic faults before beginning diagnostic routines involving pinpoint tests.

• NOTE: Inspect connectors for signs of water ingress, and pins for damage and/or corrosion.

• NOTE: If DTCs are recorded and, after performing the pinpoint tests, a fault is not present, an intermittent concern may
be the cause. Always check for loose connections and corroded terminals.

Description And Operation

For a detailed description of the driver passenger door system, refer to the relevant Description and Operation section in
the workshop manual.
For additional information, refer to: 

Handles, Locks, Latches and Entry Systems

 (501-14 Handles, Locks, Latches and Entry

Systems, Description and Operation).

Driver/passenger door module

B108F-23 Cabin

Lock/Unlock
Switch

Signal stuck low Carry out the pinpoint test associated with this DTC using the

manufacturer approved diagnostic system

B10ED-11 Rear door driver

side double
locking motor

Circuit short to
ground

Refer to the electrical circuit diagrams and check rear door driver side
double locking motor control circuit for short to ground

B10ED-15 Rear door driver

side double
locking motor

Circuit short to
power or open

Refer to the electrical circuit diagrams and check rear door driver side
double locking motor control circuit for short to power, open circuit

B10EE-11 Rear door

passenger side
double locking
motor

Circuit short to
ground

Refer to the electrical circuit diagrams and check rear door passenger
side double locking motor control circuit for short to ground

B10EE-15 Rear door

passenger side
double locking
motor

Circuit short to
power or open

Refer to the electrical circuit diagrams and check rear door passenger
side double locking motor control circuit for short to power, open circuit

B110A-11 Rear door driver

side central
locking motor

Circuit short to
ground

Refer to electrical circuit diagrams and check rear door driver side
central locking motor control circuit for short to ground

B110A-15 Rear door driver

side central
locking motor

Circuit short to
power or open

Refer to electrical circuit diagrams and check rear door driver side
central locking motor control circuit for short to power, open circuit

B110B-11 Rear door

passenger side
central locking
motor

Circuit short to
ground

Refer to electrical circuit diagrams and check rear door passenger side
central locking motor control circuit for short to ground

B110B-15 Rear door

passenger side
central locking
motor

Circuit short to
power or open

Refer to electrical circuit diagrams and check rear door passenger side
central locking motor control circuit for short to power, open circuit

B117C-07 Rear Power

Window up

Mechanical
Failure

Check for mechanical failure of rear window mechanism

B117C-72 Rear Power

Window up

Actuator Stuck
Open

Clear DTC and re-test. If DTC returns, install a new rear door module,
refer to the new module installation note at the top of the DTC Index

B117C-73 Rear Power

Window up

Actuator Stuck
Closed

Clear DTC and re-test. If DTC returns, install a new rear door module,
refer to the new module installation note at the top of the DTC Index

B117C-92 Rear Power

Window up

Performance or
incorrect
operation

Refer to electrical circuit diagrams and check power and ground
supplies to rear door module

B117D-72 Rear Power

Window down

Actuator Stuck
Open

Clear DTC and re-test. If DTC returns, install a new rear door module,
refer to the new module installation note at the top of the DTC Index

B117D-73 Rear Power

Window down

Actuator Stuck
Closed

Clear DTC and re-test. If DTC returns, install a new rear door module,
refer to the new module installation note at the top of the DTC Index

B117E-07 Front Power

Window up

Mechanical
failure

Check for mechanical failure of front window mechanism

B117E-72 Front Power

Window up

Actuator stuck
open

Clear DTC and re-test. If DTC returns, install a new DDM/PDM, refer to
the new module installation note at the top of the DTC Index

B117E-73 Front Power

Window up

Actuator stuck
closed

Clear DTC and re-test. If DTC returns, install a new DDM/PDM, refer to
the new module installation note at the top of the DTC Index

B117F-72 Front Power

Window down

Actuator stuck
open

Clear DTC and re-test. If DTC returns, install a new DDM/PDM, refer to
the new module installation note at the top of the DTC Index

B117F-73 Front Power

Window down

Actuator stuck
closed

Clear DTC and re-test. If DTC returns, install a new DDM/PDM, refer to
the new module installation note at the top of the DTC Index

B11D1-83 LIN Bus Circuit

"C"

Value of signal
protection
calculation
incorrect

Refer to the electrical circuit diagrams and test LIN circuit between
driver switch pack and DDM for short/open circuits, clear DTC and
re-test. If DTC remains install a new switch pack, refer to new
module/component installation note at the top of the DTC Index

B11D1-86 LIN Bus Circuit

"C"

Signal Invalid

Refer to the electrical circuit diagrams and test LIN circuit between
driver switch pack and DDM for short/open circuits, clear DTC and
re-test. If DTC remains install a new switch pack, refer to new
module/component installation note at the top of the DTC Index

B11D1-87 LIN Bus Circuit

"C"

Missing Message Refer to the electrical circuit diagrams and test LIN circuit between

driver switch pack and DDM for short/open circuits, clear DTC and
re-test. If DTC remains install a new switch pack, refer to new
module/component installation note at the top of the DTC Index

B11F6-11 Driver Folding

Mirror Motor

Short To Ground Refer to electrical circuit diagrams and check driver folding mirror

motor for short to ground

B11F6-15 Driver Folding

Mirror Motor

Short to power
or open

Refer to electrical circuit diagrams and check driver folding mirror
motor for short to power, open circuit

B11F7-11 Passenger

Folding Mirror
Motor

Short To Ground Refer to electrical circuit diagrams and check passenger folding mirror

motor for short to ground

B11F7-15 Passenger

Folding Mirror
Motor

Short to power
or open

Refer to electrical circuit diagrams and check passenger folding mirror
motor for short to power, open circuit

B1A98-83 LIN Bus Circuit

#1

Value of signal
protection
calculation
incorrect

Carry out the pinpoint test associated with this DTC using the
manufacturer approved diagnostic system. Refer to the electrical circuit
diagrams and test LIN circuit between driver side rear door module and
DDM for short/open circuits, clear DTC and re-test. If DTC remains
install a new switch pack, refer to new module/component installation
note at the top of the DTC Index

B1A98-86 LIN Bus Circuit

#1

Signal Invalid

Refer to the electrical circuit diagrams and test LIN circuit between
driver side rear door module and DDM for short/open circuits, clear DTC
and re-test. If DTC remains install a new switch pack, refer to new
module/component installation note at the top of the DTC Index

B1A98-87 LIN Bus Circuit

#1

Missing Message Refer to the electrical circuit diagrams and test LIN circuit between

driver side rear door module and DDM for short/open circuits, clear DTC
and re-test. If DTC remains install a new switch pack, refer to new
module/component installation note at the top of the DTC Index

B1C39-29 Key Lock Switch

Signal invalid

Carry out the associated pinpoint tests associated with this DTC using
the manufacturer approved diagnostic system

C1B15-11 Sensor Supply

#2

Short to ground

Refer to the electrical circuit diagrams and test rear window sensor
supply circuit for short to ground

C1B15-15 Sensor Supply

#2

Short to power
or open circuit

Refer to the electrical circuit diagrams and test rear window sensor
supply circuit for short to power or open circuit

U2004-24 Auxiliary Switch

Pack

Signal stuck high Carry out the pinpoint tests associated with this DTC using the

manufacturer approved diagnostic system

Driver/Passenger door module (DDM/PDM)

DTC

Description

Possible Cause

Action

B109C-15 Front Courtesy Light

Short to power or open circuit

Refer to the electrical circuit diagrams and test
front courtesy light circuit for short to power or
open circuit

B109D-11 Front Courtesy Light

Short to ground

Refer to the electrical circuit diagrams and test
front courtesy light circuit for short ground

B10EB-11 Driver door double

locking motor

Short to ground

Refer to the electrical circuit diagrams and test
driver door double locking motor circuit for short
ground

B10EB-15 Driver door double

locking motor

Short to power or open circuit

Refer to the electrical circuit diagrams and test
driver door double locking motor circuit for short to
power or open circuit

B10EC-11 Passenger door

double locking motor

Short to ground

Refer to the electrical circuit diagrams and test
passenger door double locking motor circuit for
short ground

B10EC-15 Passenger door

double locking motor

Short to power or open circuit

Refer to the electrical circuit diagrams and test
passenger door double locking motor circuit for
short to power or open circuit

DTC

Description

Possible Cause

Action

B1108-11 Driver door central

locking motor

Short to ground

Refer to the electrical circuit diagrams and test
driver door central locking motor circuit for short
ground

B1108-15 Driver door central

locking motor

Short to power or open circuit

Refer to the electrical circuit diagrams and test
driver door central locking motor circuit for short to
power or open circuit

B1109-11 Passenger door

central locking motor

Short to ground

Carry out pinpoint tests associated with this DTC
using the manufacturer approved diagnostic system

B1109-15 Passenger door

central locking motor

Short to power or open circuit

Carry out pinpoint tests associated with this DTC
using the manufacturer approved diagnostic system

B1163-11 Left Mirror Heater

Output short to
ground

Short to ground

Refer to the electrical circuit diagrams and test left
mirror heater output circuit for short to ground

B1163-15 Left Mirror Heater

Output short to
power

Short to power or open circuit

Refer to the electrical circuit diagrams and test left
mirror heater output circuit for short to power or
open circuit

B1164-11 Right Mirror Heater

Output short to
ground

Short to ground

Refer to the electrical circuit diagrams and test
right mirror heater output circuit for short to ground

B1164-15 Right Mirror Heater

Output short to
power

Short to power or open circuit

Refer to the electrical circuit diagrams and test
right mirror heater output circuit for short to power
or open circuit

B1165-11 Left Front Puddle

Lamp Output short
to ground

Short to ground

Refer to the electrical circuit diagrams and test left
front puddle lamp output circuit for short to ground

B1165-15 Left Front Puddle

Lamp Output open
load or short to
power

Short to power or open circuit

Refer to the electrical circuit diagrams and test left
front puddle lamp output circuit for short to power
or open circuit

B1166-11 Right Front Puddle

Lamp Output short
to ground

Short to ground

Refer to the electrical circuit diagrams and test
right front puddle lamp output circuit for short to
ground

B1166-15 Right Front Puddle

Lamp Output open
load or short to
battery

Short to power or open circuit

Refer to the electrical circuit diagrams and test
right front puddle lamp output circuit for short to
power or open circuit

B117E-72 Front Power Window

up

Actuator stuck open

Install a new DDM/PDM, refer to the new module
installation note at the top of the DTC Index

B117E-73 Front Power Window

up

Actuator stuck closed

Install a new DDM/PDM, refer to the new module
installation note at the top of the DTC Index

B117F-72 Front Power Window

down

Actuator stuck open

Install a new DDM/PDM, refer to the new module
installation note at the top of the DTC Index

B117F-73 Front Power Window

down

Actuator stuck closed

Install a new DDM/PDM, refer to the new module
installation note at the top of the DTC Index

B1189-29 Front Window

Position Sensor

Signal invalid

Carry out pinpoint tests associated with this DTC
using the manufacturer approved diagnostic system

B118A-29 Rear Window

Position Sensor

Signal invalid

Carry out pinpoint tests associated with this DTC
using the manufacturer approved diagnostic system

B1A94-11 Driver Mirror

Short to ground

Refer to the electrical circuit diagrams and test
driver mirror fold motor circuit for short to ground

B1A94-15 Driver Mirror

Short to power or open circuit

Refer to the electrical circuit diagrams and test
driver mirror fold motor circuit for short to power or
open circuit

B1A95-11 Passenger Mirror

Short to ground

Refer to the electrical circuit diagrams and test
passenger mirror fold motor circuit for short to
ground

B1A95-15 Passenger Mirror

Short to power or open circuit

Refer to the electrical circuit diagrams and test
passenger mirror fold motor circuit for short to
power or open circuit

B1A98-83 LIN Bus Circuit #1

Value of signal protection
calculation incorrect

Refer to the electrical circuit diagrams and test LIN
circuit between driver switch pack and DDM for
short/open circuits, clear DTC and re-test. If DTC
remains install a new switch pack, refer to new
module/component installation note at the top of
the DTC Index

B1A98-86 LIN Bus Circuit #1

Signal Invalid

Refer to the electrical circuit diagrams and test LIN
circuit between driver switch pack and DDM for
short/open circuits, clear DTC and re-test. If DTC
remains install a new switch pack, refer to new
module/component installation note at the top of
the DTC Index

B1A98-87 LIN Bus Circuit #1

Missing Message

Refer to the electrical circuit diagrams and test LIN
circuit between driver switch pack and DDM for
short/open circuits, clear DTC and re-test. If DTC
remains install a new switch pack, refer to new
module/component installation note at the top of
the DTC Index

B1C09-11 Driver Left/Right

Mirror Motor Circuit

Short to ground

Refer to the electrical circuit diagrams and test
driver left/right mirror motor circuit for short to
ground

DTC

Description

Possible Cause

Action

B1C09-15 Driver Left/Right

Mirror Motor Circuit

Short to power or open circuit

Refer to the electrical circuit diagrams and test
driver left/right mirror motor circuit for short to
power or open circuit

B1C10-11 Driver Up/Down

Mirror Motor Circuit

Short to ground

Refer to the electrical circuit diagrams and test
driver up/down mirror motor circuit for short to
ground

B1C10-15 Driver Up/Down

Mirror Motor Circuit

Short to power or open circuit

Refer to the electrical circuit diagrams and test
driver up/down mirror motor circuit for short to
power or open circuit

B1C11-11 Passenger Left/Right

Mirror Motor Circuit

Short to ground

Carry out pinpoint tests associated with this DTC
using the manufacturer approved diagnostic system

B1C11-15 Passenger Left/Right

Mirror Motor Circuit

Short to power or open circuit

Carry out pinpoint tests associated with this DTC
using the manufacturer approved diagnostic system

B1C12-11 Passenger Up/Down

Mirror Motor Circuit

Short to ground

Carry out pinpoint tests associated with this DTC
using the manufacturer approved diagnostic system

B1C12-15 Passenger Up/Down

Mirror Motor Circuit

Short to power or open circuit

Carry out pinpoint tests associated with this DTC
using the manufacturer approved diagnostic system

B1C13-11 Driver Up/Down

Mirror Motor
Feedback Circuit

Short to ground

Refer to the electrical circuit diagrams and test
driver up/down mirror motor feedback circuit for
short to ground

B1C13-15 Driver Up/Down

Mirror Motor
Feedback Circuit

Short to power or open circuit

Refer to the electrical circuit diagrams and test
driver up/down mirror motor feedback circuit for
short to power or open circuit

B1C14-11 Driver Left/Right

Mirror Motor
Feedback Circuit

Short to ground

Refer to the electrical circuit diagrams and test
driver left/right mirror motor feedback circuit for
short to ground

B1C14-15 Driver Left/Right

Mirror Motor
Feedback Circuit

Short to power or open circuit

Refer to the electrical circuit diagrams and test
driver left/right mirror motor feedback circuit for
short to power or open circuit

B1C15-11 Passenger Up/Down

Mirror Motor
Feedback Circuit

Short to ground

Refer to the electrical circuit diagrams and test
passenger up/down mirror motor feedback circuit for
short to ground

B1C15-15 Passenger Up/Down

Mirror Motor
Feedback Circuit

Short to power or open circuit

Refer to the electrical circuit diagrams and test
passenger up/down mirror motor feedback circuit for
short to power or open circuit

B1C16-11 Passenger Left/Right

Mirror Motor
Feedback Circuit

Short to ground

Refer to the electrical circuit diagrams and test
passenger left/right mirror motor feedback circuit for
short to ground

B1C16-15 Passenger Left/Right

Mirror Motor
Feedback Circuit

Short to power or open circuit

Refer to the electrical circuit diagrams and test
passenger left/right mirror motor feedback circuit for
short to power or open circuit

C1B14-11 Sensor Supply #1

Short to ground

Refer to the electrical circuit diagrams and test
window sensor supply circuit for short to ground

C1B14-15 Sensor Supply #1

Short to power or open circuit

Refer to the electrical circuit diagrams and test
window sensor supply circuit for short to power or
open circuit

U0010-00 Medium speed CAN

communication Bus

Medium speed CAN
communication Bus

Carry out pinpoint tests associated with this DTC
using the manufacturer approved diagnostic system

U0140-00 Lost communication

with CJB

Logged when subscribed CAN
message missing from CJB

Carry out pinpoint tests associated with this DTC
using the manufacturer approved diagnostic system

U0208-00 Lost communication

With Driver Seat
Module (DSM)

Missing message

Carry out pinpoint tests associated with this DTC
using the manufacturer approved diagnostic system

U0300-00 Internal control

module software
incompatibility

Invalid configuration message
is received

Re-configure the CJB using the manufacturer
approved diagnostic system. Clear the DTC and
retest. If the DTC is still logged suspect the
DDM/PDM, refer to the new module installation note
at the top of the DTC Index

U2002-24 Switch

Signal stuck high

Clear DTC and re-test. If DTC remains, install a new
passenger side window switch

U2010-11 Switch illumination

Circuit short to ground

Carry out CAN network tests using the manufacturer
approved diagnostic system

U2010-12 Switch illumination

Circuit short to battery

Carry out CAN network tests using the manufacturer
approved diagnostic system

U2012-08 Car Configuration

Parameter(s)

Bus signal/message failures

Cycle the ignition status and re-test. If DTC
remains, re-configure the RJB using the
manufacturer approved diagnostic system

U2013-24 Switch Pack

Signal stuck high

Clear DTC and re-test. If DTC remains, install a new
driver side window switch pack, refer to new
module/component installation note at the top of
the DTC Index

U2014-44 Control module

hardware

Data Memory Failure

Install a new DDM/PDM, refer to the new module
installation note at the top of the DTC Index

U2100-00 Initial configuration

not complete

No sub type information

Re-configure the DDM/PDM using the manufacturer
approved diagnostic system

U3000-49 Control module

Internal electronic failure

Install a new DDM/PDM, refer to the new module
installation note at the top of the DTC Index

 

 

 

 

 

 

 

Content   ..  19  20  21  22   ..