Discovery 2. Manual - part 375

 

  Index      Land Rover     Land Rover Discovery 2 - service manual 1999 year

 

Search            

 

 

 

 

 

 

 

 

 

Content   ..  373  374  375  376   ..

 

 

Discovery 2. Manual - part 375

 

 

GENERAL INFORMATION

03-1

GENERAL INFORMATION

General Precautions

Dangerous substances
Modern vehicles contain many materials and liquids 
which if not handled with care can be hazardous to 
both personal health and the environment.

WARNING: Many liquids and other substances 
used in motor vehicles are poisonous and should 
under no circumstances be consumed and 
should, as far as possible, be kept from contact 
with the skin. These liquids and substances 
include acid, anti-freeze, asbestos, brake fluid, 
fuel, windscreen washer additives, lubricants, 
refrigerants and various adhesives.

Always read carefully the instructions printed on 
labels or stamped on components and obey them 
implicitly. Such instructions are included for 
reasons of your health and personal safety. 
Never disregard them.

Synthetic rubber
Many 'O' rings, seals, hoses, flexible pipes and other 
similar items which appear  to be natural rubber, are 
in fact, made of synthetic materials called 
Fluoroelastomers.  Under normal operating 
conditions this material is safe and does not present 
a health hazard. However, if the material is damaged 
by fire or excessive heating, it can break down and 
produce highly corrosive Hydrofluoric acid.

Contact with Hydrofluoric acid can cause serious 
burns on contact with skin. If skin contact does occur:

l

Remove any contaminated clothing 
immediately.

l

Irrigate effected area of skin with a copious 
amount of cold water or limewater for 15 to 60 
minutes.

l

Obtain medical assistance immediately.

Should any material be in a burnt or overheated 
condition, handle with extreme caution and wear 
protective clothing (seamless industrial gloves, 
protective apron etc.).

Decontaminate and dispose of gloves immediately 
after use.

Lubricating oils
Avoid excessive skin contact with used lubricating 
oils and always adhere to the health protection 
precautions.

WARNING: Avoid excessive skin contact with 
used engine oil. Used engine oil contains 
potentially harmful contaminants which may 
cause skin cancer or other serious skin 
disorders.

WARNING: Avoid excessive skin contact with 
mineral oil. Mineral oils remove the natural fats 
from the skin, leading to dryness, irritation and 
dermatitis.

Health protection precautions
The following precautions should be observed at all 
times.

l

Wear protective clothing, including impervious 
gloves where practicable.

l

Avoid prolonged and repeated contact with oils, 
particularly used engine oils. 

l

Do not put oily rags in pockets. 

l

Avoid contaminating clothes (particularly those 
next to the skin) with oil. 

l

Overalls must be cleaned regularly. Discard 
heavily soiled clothing and oil impregnated 
footwear. 

l

First aid treatment should be obtained 
immediately for open cuts and wounds. 

l

Apply barrier creams before each work period to 
help prevent lubricating oil from contaminating 
the skin.

l

Wash with soap and water to ensure all oil is 
removed (proprietary skin cleansers and nail 
brushes will help).

l

Use moisturisers after cleaning; preparations 
containing lanolin help replace the skin's natural 
oils which have been removed. 

l

Do not use petrol/gasoline, kerosene, diesel 
fuel, oil, thinners or solvents for cleaning skin. 

l

Where practicable, degrease components prior 
to handling.

l

If skin disorders develop, obtain medical advice 
without delay.

l

Wear eye protection (e.g. goggles or face 
shield) if there is a risk of eye contamination. 
Eye wash facilities should be provided in close 
vicinity of the work area.

GENERAL INFORMATION

03-2

Safety Instructions

Whenever possible, use a lift or pit when working 
beneath vehicle, in preference to jacking. Chock 
wheels as well as applying parking brake.

Jacking
Always use the recommended jacking points.

Always ensure that any lifting apparatus has 
sufficient load capacity for the weight to be lifted.

Ensure the vehicle is standing on level ground prior 
to lifting or jacking.

Apply the handbrake and chock the wheels.

WARNING: Do not work on or under a vehicle 
supported only by a jack. Always support the 
vehicle on safety stands.

Do not leave tools, lifting equipment, spilt oil, etc. 
around or on the work bench area. Always keep a 
clean and tidy work area.

Brake shoes and pads
Always fit the correct grade and specification of 
brake linings. When renewing brake pads and brake 
shoes, always replace as complete axle sets.

Brake hydraulics
Observe the following recommendations when 
working on the brake system:

l

Always use two spanners when loosening or 
tightening brake pipe or hose connections.

l

Ensure that hoses run in a natural curve and are 
not kinked or twisted.

l

Fit brake pipes securely in their retaining clips 
and ensure that the pipe cannot contact a 
potential chafing point.

l

Containers used for brake fluid must be kept 
absolutely clean.

l

Do not store brake fluid in an unsealed 
container, it will absorb water and in this 
condition would be dangerous to use due to a 
lowering of its boiling point.

l

Do not allow brake fluid to be contaminated with 
mineral oil, or put new brake fluid in a container 
which has previously contained mineral oil.

l

Do not re-use brake fluid removed from the 
system.

l

Always use clean brake fluid or a recommended 
alternative to clean hydraulic components.

l

After disconnection of brake pipes and hoses, 
immediately fit suitable blanking caps or plugs to 
prevent the ingress of dirt.

l

Only use the correct brake fittings with 
compatible threads.

l

Observe absolute cleanliness when working 
with hydraulic components.

Cooling system caps and plugs
Extreme care is necessary when removing 
expansion tank caps and coolant drain or bleed 
screws when the engine is hot, especially if it is 
overheated. To avoid the possibility of scalding, 
allow the engine to cool before attempting removal.

GENERAL INFORMATION

03-3

Environmental Precautions

General
This section provides general information  which  can 
help to reduce the environmental  impacts from the 
activities carried out in workshops.

Emissions to air  
Many of the activities that are carried out in 
workshops emit gases and fumes which contribute to 
global warming, depletion of the ozone layer and/or 
the formation of  photochemical smog at ground 
level. By considering how the workshop activities are 
carried out,  these gases and fumes can be 
minimised, thus reducing the impact on the 
environment.

Exhaust fumes
Running car engines is an essential part of workshop 
activities and exhaust fumes need to be  ventilated to 
atmosphere.  However, the amount of time engines 
are running and the position of the  vehicle should be 
carefully considered at all times, to reduce the 
release of poisonous gases and minimise the 
inconvenience to people living nearby.

Solvents 
Some of the cleaning agents used are solvent based 
and will evaporate to atmosphere if used  carelessly, 
or if cans are left unsealed.  All solvent containers 
should be firmly closed when not  needed and 
solvent should be used sparingly. Suitable 
alternative materials may be available  to replace 
some of the commonly used solvents.  Similarly, 
many paints are solvent based and  the spray should 
be minimised to reduce solvent emissions.  

Refrigerant
It is illegal to release any refrigerants into the 
atmosphere. Discharge and replacement of these  
materials from air conditioning units should only be 
carried out using the correct equipment.  

Checklist 
Always adhere to the following.

Engines:

l

don't leave engines running unnecessarily;

l

minimise testing times and check where the 
exhaust fumes are being blown.  

Materials: 

l

keep lids on containers of solvents; 

l

only use the minimum quantity; 

l

consider alternative materials;

l

minimise over-spray when painting. 

Gases:

l

use the correct equipment for collecting 
refrigerants;

l

don't burn rubbish on site. 

Discharges to water
Most sites will have two systems for discharging 
water: storm drains and foul drains. Storm drains 
should only receive clean water, foul drains will take 
dirty water.     

The foul drain will accept many of the normal waste 
waters such as washing water, detergents  and 
domestic type wastes, but oil, petrol, solvent, acids, 
hydraulic oil, antifreeze and other such  substances 
should never be poured down the drain.  If in any 
doubt speak to the Water  Company first. 

Every precaution must be taken to prevent spillage of 
oil, fuel, solvents etc. reaching the drains.   All 
handling of such materials must take place well away 
from the drains and preferably in an  area with a kerb 
or wall around it, to prevent discharge into the drain. 
If a spillage occurs it  should be soaked up 
immediately.  Having a spill kit available will make 
this easier. 

Additional precautions 
Check whether the surface water drains are 
connected to an oil water separator, this could  
reduce the pollution if an incident was to occur. Oil 
water separators do need regular maintenance to  
ensure effectiveness.  

Checklist
Always adhere to the following.

Disposal:

l

never pour anything down a drain without first 
checking  that it is environmentally safe to do so, 
and that it does not contravene any local 
regulations or bye-laws;

l

 have oil traps emptied regularly.

Spillage prevention:

l

store liquids in a walled area;

l

make sure that taps on liquid containers are 
secure and cannot be accidentally turned on;

l

protect bulk storage tanks from vandalism by 
locking the valves;

l

transfer liquids from one container to another in 
an area away from open drains;

l

ensure lids are replaced securely on containers;

l

have spill kits available near to points of storage 
and handling of liquids.

GENERAL INFORMATION

03-4

Spill kits
Special materials are available to absorb a number of 
different substances.   They can be in granular form, 
ready to use and bought in convenient  containers for 
storage.  Disposal of used spill-absorbing material is 
dealt with in 'Waste Management' section.

Land contamination 
Oils, fuels and solvents etc. can contaminate any soil 
that they are allowed to contact.  Such materials 
should never be disposed of by pouring onto soil and  
every precaution must be taken to prevent spillage 
reaching soil. Waste materials stored on open 
ground could also leak, or have polluting substances 
washed  off them that would contaminate the land. 
Always store these materials in suitable skips or  
other similarly robust containers.  

Checklist 
Always adhere to the following.

l

Don't pour or spill anything onto the soil or bare 
ground;

l

don't store waste materials on bare ground, see 
'Spillage prevention' list.

Legal compliance  
Some sites may have a discharge consent for 
effluent discharge to the foul drain for a car  wash etc. 
It is important to know what materials are allowed in 
the drain and to check the  results of any monitoring 
carried out by the Water Company. 

Where paint-spraying operations are carried out it 
may be necessary to apply to the Local  Authority for 
an air emissions licence to operate the plant.  If such 
a licence is in operation, additional precautions will 
be necessary to comply with the requirements, and 
the results of  any air quality monitoring must be 
checked regularly.  

Checklist
Always adhere to the following.

l

Know what legal consents and licences apply to 
the operations;

l

check that the emissions and discharges 
comply with legal requirements.

Local issues  
A number of environmental issues will be of 
particular concern to residents and other  neighbours 
close to the site.  The sensitivity of these issues will 
depend on the proximity of the site and the layout 
and amount of activity carried on at the site.

 Noise is a major concern and therefore  
consideration should be given to the time spent  
carrying out noisy activities and the location of those 
activities that can cause excessive noise.   

Car alarm testing, panel beating, hammering and 
other such noisy activities should, whenever 
possible, be carried  out  indoors with doors and 
windows shut or as far away from houses as  
possible.

Running vehicle engines may  be an outside activity 
which could cause nuisance to  neighbours because 
of both noise and smell.

Be sensitive to the time of day when these  activities 
are carried out and minimise the  time of the noisy 
operation, particularly in  the early morning and late 
evening. 

Another local concern will be the smell from the 
various materials used.  Using less solvent,  paint 
and petrol could help prevent this annoyance.

Local residents and other business users will also be 
concerned about traffic congestion, noise  and 
exhaust fumes, be sensitive to these concerns and 
try to minimise inconvenience from  deliveries, 
customers and servicing operations.

Checklist
Always adhere to the following.

l

Identify where the neighbours who are likely to 
be affected are situated;

l

minimise noise, smells and traffic nuisance;

l

prevent litter by putting waste in the correct  
containers;

l

have waste skips emptied regularly.

Use of resource 
Another environmental concern is the waste of 
materials and energy that can occur in day to  day 
activities.

Electricity for heating, lighting and compressed air 
uses resources and releases pollution during its 
generation.

Fuel used for heating, running cars or vans and 
mobile plant  is another limited resource which  
consumes large amounts of energy during its 
extraction and refining processes.

Water has to be cleaned, piped to site and disposed 
of; all of which creates more potential pollution.

Oil, spares, paint etc., have all produced pollution in 
the process of manufacture and they become a  
waste disposal problem if discarded.

Checklist
Always adhere to the following.

 

 

 

 

 

 

 

Content   ..  373  374  375  376   ..