Jeep XJ. Manual - part 897

 

  Index      Jeep     Jeep XJ - service repair manual 2001 year

 

Search            

 

 

 

 

 

 

 

 

 

Content   ..  895  896  897  898   ..

 

 

Jeep XJ. Manual - part 897

 

 

Symptom:

P1747-SOLENOID B SHORTED TO VOLTAGE OR OPEN

When Monitored and Set Condition:

P1747-SOLENOID B SHORTED TO VOLTAGE OR OPEN

When Monitored:

Continuously while in 3rd or 4th gear.

Set Condition:

Solenoid B is turned off and voltage is detected on the Solenoid B Control

circuit.

POSSIBLE CAUSES

INTERMITTENT WIRING AND/OR CONNECTORS

OPEN BETWEEN THE 8-WAY CONNECTOR AND TCM CONNECTOR

SHORT TO VOLTAGE BETWEEN THE 8-WAY CONNECTOR AND THE TCM CONNECTOR

OPEN BETWEEN THE 8-WAY CONNECTOR AND SOLENOID B CONNECTOR

OPEN OR HIGH RESISTANCE TRANSMISSION CASE GROUND

SHORT TO VOLTAGE BETWEEN THE 8-WAY CONNECTOR AND THE SOLENOID B CONNEC-
TOR

SOLENOID B - RESISTANCE OUT OF RANGE

TCM - SOLENOID B CONTROL CIRCUIT

TEST

ACTION

APPLICABILITY

1

NOTE: Always perform diagnostics with a fully charged battery to avoid
diagnosing false symptoms.
NOTE: Low fluid level can be the cause of many transmission problems. If
the fluid level is low locate and repair the leak then check and adjust the
fluid level per the service information.
Using the wiring diagram/schematic as a guide, inspect the wiring and connectors.
Repair as necessary.
Verify the brake switch input to the TCM is working correctly.
Perform the shift lever position test and adjust the linkage if necessary.
Test drive vehicle to verify customer complaint.
With the DRBIII

t, read the PCM DTC’s. Check and repair all PCM DTC’s before

performing transmission diagnostics.
With the DRBIII

t, read the TCM DTC’s.

Note: Check 1 trip failures and diagnose them as DTC’s (Hard codes)
Most DTC’s set on start up but some must be set by driving the vehicle such that all
diagnostic monitors have run.
Note: Verify flash level of transmission controller. Some problems are
corrected by software upgrades to the transmission controller.
NOTE: Check for applicable TSB’s related to the problem.
Perform this procedure prior to symptom diagnosis.

All

Continue

Go To

2

57

TRANSMISSION

TEST

ACTION

APPLICABILITY

2

When monitored: Continuously while in 3rd or 4th gear.
When set: Solenoid B is turned off and voltage is detected on the Solenoid B Control
circuit.
This is the When monitored / When set conditions for DTC P1747.

All

Continue

Go To

3

3

With the DRBIII

t, erase DTC’s.

NOTE: The vehicle must be driven on the road for the next step.
Place the gear selector in the 3 range.
Accelerate the vehicle to 40 MPH and hold for 30 seconds.
Did the DTC P1747 reset?

All

Yes

Go To

4

No

Go To

11

4

Turn ignition off to the lock position.
Disconnect the TCM harness connector.
Disconnect the 8-way harness connector.
NOTE: Check connectors - Clean/repair as necessary.
Measure the resistance of the Solenoid B Control circuit between the 8-WAY
connector and the TCM connector.
Is the resistance above 5.0 ohms?

All

Yes

Repair the open Solenoid B Control circuit.
Perform AW4 TRANS VERIFICATION TEST-VER1.

No

Go To

5

5

Turn ignition off to the lock position.
Disconnect the Transmission Solenoid 8-Way harness connector.
NOTE: Check connectors - Clean/repair as necessary.
Turn the ignition on.
Measure the voltage of the Solenoid B Control circuit in the 8-way connector.
Is there any voltage present?

All

Yes

Repair the Solenoid B Control circuit for a short to voltage.
Perform AW4 TRANS VERIFICATION TEST-VER1.

No

Go To

6

6

Turn ignition off to the lock position.
Disconnect the Transmission Solenoid 8-way harness connector.
Remove the Transmission Oil Pan, per the Service Information.
Disconnect the Transmission Solenoid B harness connector.
NOTE: Check connectors - Clean/repair as necessary.
Measure the resistance of the Solenoid B Control circuit between the 8-WAY
connector and the Solenoid B connector.
Is the resistance above 5.0 ohms?

All

Yes

Repair the open Solenoid B Control circuit.
Perform AW4 TRANS VERIFICATION TEST-VER1.

No

Go To

7

58

TRANSMISSION

P1747-SOLENOID B SHORTED TO VOLTAGE OR OPEN —

Continued

TEST

ACTION

APPLICABILITY

7

With the DRBIII

t, read DTC’s.

Are DTC’s P1745 and P1749 present in addition to the P1747 DTC?

All

Yes

Repair the open or high resistance Transmission Case Ground.
Perform AW4 TRANS VERIFICATION TEST-VER1.

No

Go To

8

8

Turn ignition off to the lock position.
Remove the Transmission Oil Pan, refer to the Service Information.
Disconnect the Solenoid B harness connector.
NOTE: Check connectors - Clean/repair as necessary.
Turn the ignition on.
Measure the voltage of the Solenoid B Control circuit in the Solenoid B connector.
Is there any voltage present?

All

Yes

Repair the Solenoid B Control circuit for a short to voltage.
Perform AW4 TRANS VERIFICATION TEST-VER1.

No

Go To

9

9

Turn ignition off to the lock position.
Remove the Transmission Oil Pan, refer to the service information.
Disconnect the Solenoid B harness connector.
NOTE: Check connectors - Clean/repair as necessary.
Measure the resistance of Solenoid B from the solenoid mounting bracket to the
solenoid wire terminal.
Is the resistance between 11.0 and 15.0 ohms?

All

Yes

Go To

10

No

Replace Solenoid B.
Perform AW4 TRANS VERIFICATION TEST-VER1.

10

If there are no possible causes remaining, view repair.

All

Repair

Replace the TCM.
Perform AW4 TRANS VERIFICATION TEST-VER1.

11

Using the when monitored / when set conditions, attempt to reset the DTC. If the
DTC can be reset return to the symptom list and perform the appropriate diagnostic
test.
Using the wiring diagram/schematic as a guide, inspect the wiring and connectors.
NOTE: Check the Technical Service Bulletins.
Were any problems found?

All

Yes

Repair the wiring and/or connectors as necessary.
Perform AW4 TRANS VERIFICATION TEST-VER1.

No

Test Complete.

59

TRANSMISSION

P1747-SOLENOID B SHORTED TO VOLTAGE OR OPEN —

Continued

Symptom:

P1748-SOLENOID C SHORTED TO GROUND

When Monitored and Set Condition:

P1748-SOLENOID C SHORTED TO GROUND

When Monitored:

Continuously while Solenoid C (TCC) is energized.

Set Condition:

Solenoid C (TCC) is turned off and low voltage is detected on the Solenoid

C Control circuit for 12.5 seconds.

POSSIBLE CAUSES

INTERMITTENT WIRING AND/OR CONNECTORS

SHORT TO GROUND BETWEEN THE 8-WAY CONNECTOR AND THE TCM CONNECTOR

SHORT TO GROUND BETWEEN THE 8-WAY CONNECTOR AND THE SOLENOID C CONNEC-
TOR

SOLENOID C - RESISTANCE OUT OF RANGE

TCM - SOLENOID C CONTROL CIRCUIT

TEST

ACTION

APPLICABILITY

1

NOTE: Always perform diagnostics with a fully charged battery to avoid
diagnosing false symptoms.
NOTE: Low fluid level can be the cause of many transmission problems. If
the fluid level is low locate and repair the leak then check and adjust the
fluid level per the service information.
Using the wiring diagram/schematic as a guide, inspect the wiring and connectors.
Repair as necessary.
Verify the brake switch input to the TCM is working correctly.
Perform the shift lever position test and adjust the linkage if necessary.
Test drive vehicle to verify customer complaint.
With the DRBIII

t, read the PCM DTC’s. Check and repair all PCM DTC’s before

performing transmission diagnostics.
With the DRBIII

t, read the TCM DTC’s.

Note: Check 1 trip failures and diagnose them as DTC’s (Hard codes)
Most DTC’s set on start up but some must be set by driving the vehicle such that all
diagnostic monitors have run.
Note: Verify flash level of transmission controller. Some problems are
corrected by software upgrades to the transmission controller.
NOTE: Check for applicable TSB’s related to the problem.
Perform this procedure prior to symptom diagnosis.

All

Continue

Go To

2

2

When monitored: Continuously while Solenoid C is energized.
When set: Solenoid C is turned off and low voltage is detected on the Solenoid C
Control circuit for 12.5 seconds.
This is the When monitored / When set conditions for DTC P1748.

All

Continue

Go To

3

60

TRANSMISSION

 

 

 

 

 

 

 

Content   ..  895  896  897  898   ..