Jeep XJ. Manual - part 864

 

  Index      Jeep     Jeep XJ - service repair manual 2001 year

 

Search            

 

 

 

 

 

 

 

 

 

Content   ..  862  863  864  865   ..

 

 

Jeep XJ. Manual - part 864

 

 

TEST

ACTION

APPLICABILITY

7

Turn the ignition off.
Disconnect the Speed Control On/Off Switch 2-way harness connector only.
Note: Check connectors - Clean/repair as necessary.
Turn the ignition on.
Measure the S/C Switch Signal Circuit for voltage at the On/Off Switch 2-way
connector.
Is the voltage above 6.0 volts?

All

Yes

Repair the Speed Control Switch Signal Circuit for a short to
voltage.
Perform POWERTRAIN VERIFICATION TEST VER - 4.

No

Go To

8

8

Turn the ignition off.
Disconnect the Clockspring 6-way harness connector (instrument panel harness side)
.
Disconnect the PCM harness connector.
Note: Check connectors - Clean/repair as necessary.
Using an Ohmmeter, measure the resistance of the S/C Switch Signal Circuit from
the PCM to the Clockspring Connector.
Is the resistance below 5.0 ohms?

All

Yes

Go To

9

No

Repair open Speed Control Switch Signal Circuit PCM to Clock-
spring.
Perform POWERTRAIN VERIFICATION TEST VER - 4.

9

Turn the ignition off.
Disconnect the On/Off switch 2-way harness connector.
Disconnect the upper clockspring harness connector.
Note: Check connectors - Clean/repair as necessary.
Measure the resistance of the S/C Switch Signal Circuit from the clockspring harness
connector to the On/Off switch harness connector.
Is the resistance below 5.0 ohms?

All

Yes

Go To

10

No

Repair the open Speed Control Switch Signal Circuit Clockspring
to S/C switch.
Perform POWERTRAIN VERIFICATION TEST VER - 4.

10

If there are no possible causes remaining, replace the Powertrain Control Module.
View repair options.

All

Repair

Replace Powertrain Control Module.
Perform POWERTRAIN VERIFICATION TEST VER - 4.

217

SPEED CONTROL

P1596-SPEED CONTROL SWITCH ALWAYS HIGH —

Continued

Symptom:

P1597-SPEED CONTROL SWITCH ALWAYS LOW

When Monitored and Set Condition:

P1597-SPEED CONTROL SWITCH ALWAYS LOW

When Monitored:

With the ignition key on and battery voltage above 10.4 volts.

Set Condition:

When switch voltage is less than 0.39 volts for 2 minutes.

POSSIBLE CAUSES

CLOCKSPRING SHORTED TO GROUND

S/C WIRING HARNESS OBSERVABLE PROBLEM

S/C SWITCH (ON/OFF)

S/C SWITCH (RESUME/ACCEL)

S/C SIGNAL CIRCUIT SHORTED TO SENSOR GROUND

S/C SWITCH SIGNAL CIRCUIT SHORTED TO GROUND

PCM

TEST

ACTION

APPLICABILITY

1

Turn the ignition on.
With the DRBIII

t, read the S/C Switch volts status.

Is the S/C Switch voltage below 1.0 volt?

All

Yes

Go To

2

No

Go To

8

2

Turn the ignition off.
Disconnect the S/C ON/OFF Switch harness connector.
Note: Check connectors - Clean/repair as necessary.
Turn the ignition on.
With the DRBIII

t in Sensors, read the S/C Switch volts.

Did the S/C Switch volts change to 5.0 volts?

All

Yes

Replace the S/C ON/OFF Switch.
Perform POWERTRAIN VERIFICATION TEST VER - 4.

No

Go To

3

3

Turn the ignition off.
Disconnect the S/C RESUME/ACCEL Switch harness connector.
Note: Check connectors - Clean/repair as necessary.
Ignition on, engine not running.
With the DRBIII

t in Sensors, read the S/C Switch volts.

Did the S/C Switch volts go above 4.0 volts?

All

Yes

Replace the Resume/Accel Switch.
Perform POWERTRAIN VERIFICATION TEST VER - 4.

No

Go To

4

218

SPEED CONTROL

TEST

ACTION

APPLICABILITY

4

Turn the ignition off.
Disconnect the clockspring 6-way harness connector (instrument panel wiring side).
Turn the ignition on.
With the DRBIII

t in Sensors, read the S/C Switch volts.

Did the S/C Switch volts change to 5.0 volts?

All

Yes

Replace the Clockspring.
Perform POWERTRAIN VERIFICATION TEST VER - 4.

No

Go To

5

5

Turn the ignition off.
Disconnect the S/C ON/OFF Switch harness connector.
Disconnect the PCM harness connectors.
Note: Check connectors - Clean/repair as necessary.
Measure the resistance between the S/C Signal Circuit and the Sensor Ground
Circuit at the ON/OFF switch harness connector.
Is the resistance below 5.0 ohms?

All

Yes

Repair S/C Signal Circuit shorted to Sensor Ground.
Perform POWERTRAIN VERIFICATION TEST VER - 4.

No

Go To

6

6

Turn the ignition off.
Disconnect the S/C ON/OFF Switch harness connector.
Disconnect the PCM harness connectors.
Note: Check connectors - Clean/repair as necessary.
Measure the resistance between the S/C Switch Signal circuit and ground (B-) at S/C
ON/OFF Switch harness connector.
Is the resistance below 5.0 ohms?

All

Yes

Repair S/C Switch Signal Circuit for a short to ground.
Perform POWERTRAIN VERIFICATION TEST VER - 4.

No

Go To

7

7

If there are no possible causes remaining, replace the Powertrain Control Module.
View repair options.

All

Repair

Replace the Powertrain Control Module.
Perform POWERTRAIN VERIFICATION TEST VER - 4.

8

Turn the ignition off.
Using the Schematics as a guide, inspect the Wiring and Connectors.
Were any problems found?

All

Yes

Repair as necessary.
Perform POWERTRAIN VERIFICATION TEST VER - 4.

No

Test Complete.

219

SPEED CONTROL

P1597-SPEED CONTROL SWITCH ALWAYS LOW —

Continued

Symptom:

*BRAKE SWITCH SENSE STATUS DOES NOT CHANGE ON DRB

POSSIBLE CAUSES

BRAKE LAMP SWITCH GROUND CIRCUIT OPEN

BRAKE LAMP SWITCH SENSE CIRCUIT OPEN

BRAKE LAMP SWITCH SENSE CIRCUIT SHORT TO GROUND

BRAKE SWITCH (SENSE CKT)

POWERTRAIN CONTROL MODULE (BRAKE SENSE)

TEST

ACTION

APPLICABILITY

1

Turn the ignition off.
Disconnect the Brake Lamp Switch harness connector.
Measure the resistance between ground and the Brake Lamp Switch Ground circuit.
Is the resistance below 5.0 ohms?

All

Yes

Go To

2

No

Repair the Brake Lamp Switch Ground circuit for an open.
Perform POWERTRAIN VERIFICATION TEST VER - 4.

2

Turn the ignition off.
Disconnect the Brake Lamp Switch harness connector.
Disconnect the PCM harness connectors.
Measure the resistance of the Brake Lamp Switch Sense circuit.
Is the resistance below 5.0 ohms?

All

Yes

Go To

3

No

Repair the Brake Lamp Switch Sense circuit for an open.
Perform POWERTRAIN VERIFICATION TEST VER - 4.

3

Turn the ignition off.
Disconnect the Brake Lamp Switch harness connector.
Note: Check connectors - Clean/repair as necessary.
Measure the resistance between the Brake Lamp Switch Sense terminal and the
Ground terminal (measurement taken across switch).
Apply and release the Brake Pedal while monitoring the ohmmeter.
Does the resistance change from below 5.0 ohms to open circuit?

All

Yes

Go To

4

No

Replace the Brake Switch.
Perform POWERTRAIN VERIFICATION TEST VER - 4.

4

Turn the ignition off.
Disconnect the Brake Lamp Switch harness connector.
Disconnect the PCM harness connectors.
Disconnect the CAB harness connector.
Measure the resistance between ground and the Brake Lamp Switch Sense circuit.
Is the resistance below 5.0 ohms?

All

Yes

Repair the Brake Lamp Switch Sense circuit for a short to ground.
Perform POWERTRAIN VERIFICATION TEST VER - 4.

No

Go To

5

220

SPEED CONTROL

 

 

 

 

 

 

 

Content   ..  862  863  864  865   ..