Jeep XJ. Manual - part 844

 

  Index      Jeep     Jeep XJ - service repair manual 2001 year

 

Search            

 

 

 

 

 

 

 

 

 

Content   ..  842  843  844  845   ..

 

 

Jeep XJ. Manual - part 844

 

 

TEST

ACTION

APPLICABILITY

3

Turn the ignition off.
Disconnect the PCM harness connector(s).
Disconnect the Vehicle Speed Sensor harness connector.
Note: Check connectors - Clean/repair as necessary.
Measure the resistance of the Vehicle Speed Sensor Ground circuit.
Is the resistance above 5.0 ohms?

All

Yes

Repair the Vehicle Speed Sensor Ground circuit for an open.
Perform POWERTRAIN VERIFICATION TEST VER - 5.

No

Go To

4

4

Turn the ignition off.
Disconnect the PCM harness connector(s).
Disconnect the Vehicle Speed Sensor harness connector.
Note: Check connectors - Clean/repair as necessary.
Measure the resistance of the Vehicle Speed Signal circuit between the PCM
connector and the VSS connector.
Is the resistance above 5.0 ohms?

All

Yes

Repair the Vehicle Speed Signal circuit for an open.
Perform POWERTRAIN VERIFICATION TEST VER - 5.

No

Go To

5

5

Turn the ignition off.
Disconnect the PCM harness connector(s).
Disconnect the Vehicle Speed Sensor harness connector.
Note: Check connectors - Clean/repair as necessary.
Measure the resistance between ground and the Vehicle Speed Signal circuit.
Is the resistance below 5.0 ohms?

All

Yes

Repair the Vehicle Speed Signal circuit for a short to ground.
Perform POWERTRAIN VERIFICATION TEST VER - 5.

No

Go To

6

6

Turn the ignition off.
Disconnect the Vehicle Speed Sensor harness connector.
Note: Check connectors - Clean/repair as necessary.
Turn the ignition on.
Measure the voltage of the Vehicle Speed Signal circuit in the Vehicle Speed Sensor
harness connector.
Is the voltage above 6.0 volts?

All

Yes

Repair the Vehicle Speed Signal circuit for a short to voltage.
Perform POWERTRAIN VERIFICATION TEST VER - 5.

No

Test Complete.

137

DRIVEABILITY - GAS

P0500-NO VEHICLE SPEED SENSOR SIGNAL —

Continued

TEST

ACTION

APPLICABILITY

7

At this time, the conditions required to set the DTC are not present.
Note: Use the Freeze Frame Data to help duplicate the conditions that set
the DTC. Pay particular attention to the DTC set conditions, such as, VSS,
MAP, ECT, and Load.
Note: Visually inspect the related wiring harness. Look for any chafed,
pierced, pinched, or partially broken wires.
Note: Visually inspect the related wiring harness connectors. Look for
broken, bent, pushed out, or corroded terminals.
Note: Refer to any technical service bulletins that may apply.
Perform a wiggle test of the wiring harnesses and connectors while the engine is
running with the vehicle in gear on a hoist. Watch for the Good Trip Counter to
change to zero.
Were any problems found?

All

Yes

Repair as necessary.
Perform POWERTRAIN VERIFICATION TEST VER - 5.

No

Test Complete.

138

DRIVEABILITY - GAS

P0500-NO VEHICLE SPEED SENSOR SIGNAL —

Continued

Symptom:

P0505-IDLE AIR CONTROL MOTOR CIRCUITS

When Monitored and Set Condition:

P0505-IDLE AIR CONTROL MOTOR CIRCUITS

When Monitored:

At power-up and battery voltage greater than 11.5 volts.

Set Condition:

The PCM senses a short to ground or battery voltage on any of the four

Idle Air Control (IAC) driver circuits for 100 msec while the IAC motor is active.

POSSIBLE CAUSES

IAC MOTOR WIRING HARNESS OBSERVABLE

IAC MOTOR WIRING HARNESS INTERMITTENT

IAC #1 DRIVER CIRCUIT SHORTED TO #2, #3, OR #4

IAC #2 DRIVER CIRCUIT SHORTED TO #3 OR #4

IAC #3 DRIVER CIRCUIT SHORTED TO #4

IAC MOTOR

IAC #1 DRIVER CIRCUIT SHORTED TO GROUND

IAC #2 DRIVER CIRCUIT SHORTED TO GROUND

IAC #3 DRIVER CIRCUIT SHORTED TO GROUND

IAC #4 DRIVER CIRCUIT SHORTED TO GROUND

IAC #1 DRIVER CIRCUIT OPEN

IAC #2 DRIVER CIRCUIT OPEN

IAC #3 DRIVER CIRCUIT OPEN

IAC #4 DRIVER CIRCUIT OPEN

POWERTRAIN CONTROL MODULE (IAC #1 DRIVER)

POWERTRAIN CONTROL MODULE (IAC #2 DRIVER)

POWERTRAIN CONTROL MODULE (IAC #3 DRIVER)

POWERTRAIN CONTROL MODULE (IAC #4 DRIVER)

TEST

ACTION

APPLICABILITY

1

Turn the ignition on.
With the DRBIII

t, read the DTC’s.

Is the Good Trip Counter displayed and equal to zero for P0505?

All

Yes

Go To

2

No

Go To

22

139

DRIVEABILITY - GAS

TEST

ACTION

APPLICABILITY

2

Start the engine and let idle.
Disconnect the IAC Motor harness connector.
Note: Check connectors - Clean/repair as necessary.
Measure the voltage of the IAC #1 Driver Circuit.
Was the voltage over 5.0 volts at any time?

All

Yes

Go To

3

No

Go To

19

3

Start the engine. Allow the engine to idle.
Disconnect the IAC Motor harness connector.
Note: Check connectors - Clean/repair as necessary.
Measure the voltage of the IAC #2 Driver Circuit.
Was the voltage over 5.0 volts at any time?

All

Yes

Go To

4

No

Go To

16

4

Start the engine. Allow the engine to idle.
Disconnect the IAC Motor harness connector.
Note: Check connectors - Clean/repair as necessary.
Measure the voltage of the IAC #3 Driver Circuit.
Was the voltage over 5.0 volts at any time?

All

Yes

Go To

5

No

Go To

13

5

Start the engine. Allow the engine to idle.
Disconnect the IAC Motor harness connector.
Note: Check connectors - Clean/repair as necessary.
Measure the voltage of the IAC #4 Driver Circuit.
Was the voltage over 5.0 volts at any time?

All

Yes

Go To

6

No

Go To

10

6

Turn the ignition off.
Disconnect the IAC Motor harness connector.
Disconnect the PCM harness connector(s).
Note: Check connectors - Clean/repair as necessary.
Note: The following steps are checking for a short between the IAC Driver
Circuits.
Measure the resistance between the IAC #1 Driver circuit and #2, #3, #4 Driver
circuits.
Is the resistance below 5.0 ohms on any of the Drivers?

All

Yes

Repair the IAC Driver Circuits shorted together.
Perform POWERTRAIN VERIFICATION TEST VER - 5.

No

Go To

7

140

DRIVEABILITY - GAS

P0505-IDLE AIR CONTROL MOTOR CIRCUITS —

Continued

 

 

 

 

 

 

 

Content   ..  842  843  844  845   ..