Jeep XJ. Manual - part 829

 

  Index      Jeep     Jeep XJ - service repair manual 2001 year

 

Search            

 

 

 

 

 

 

 

 

 

Content   ..  827  828  829  830   ..

 

 

Jeep XJ. Manual - part 829

 

 

Symptom List:

P0133-1/1 O2 SENSOR SLOW RESPONSE
P0139-1/2 O2 SENSOR SLOW RESPONSE
P0153-2/1 O2 SENSOR SLOW RESPONSE
P0159-2/2 O2 SENSOR SLOW RESPONSE

Test Note:

All symptoms listed above are diagnosed using the same tests.

The title for the tests will be P0133-1/1 O2 SENSOR SLOW
RESPONSE.

When Monitored and Set Condition:

P0133-1/1 O2 SENSOR SLOW RESPONSE

When Monitored:

With ECT greater than 147°F, after reaching a vehicle speed of 10 mph,

and the throttle remaining open (off idle) for 2 minutes, bring the vehicle to a stop and
allow the engine to idle with the transmission in DRIVE.

Set Condition:

The oxygen sensor signal voltage is switching from below 0.27 volts to

above 0.62 volts and back fewer times than required.

P0139-1/2 O2 SENSOR SLOW RESPONSE

When Monitored:

Start engine. Allow engine to idle. For 1st part of test, if limits are

exceeded, test passes. If not, 2nd part of test runs. amb/batt temp >44°F, Baro >22.13

9

H2O, battery >10.5 volts, MAP >11.79 & <18.15

9 H2O, RPM >1350 & <2200 and vss >50

and <65.

Set Condition:

The oxygen sensor signal voltage is switching from below 0.39 volts to

above 0.58 volts and back fewer times than required.

P0153-2/1 O2 SENSOR SLOW RESPONSE

When Monitored:

With ECT greater than 147°F, after reaching a vehicle speed of 10 mph,

and the throttle remaining open (off idle) for 2 minutes, bring the vehicle to a stop and
allow the engine to idle with the transmission in DRIVE.

Set Condition:

The oxygen sensor signal voltage is switching from below 0.27 volts to

above 0.62 volts and back fewer times than required.

P0159-2/2 O2 SENSOR SLOW RESPONSE

When Monitored:

Start engine. Allow engine to idle. For 1st part of test, if limits are

exceeded, test passes. If not, 2nd part of test runs. amb/batt temp >44°F, Baro >22.13

9

H2O, battery >10.5 volts, MAP >11.79 & <18.15

9 H2O, RPM >1350 & <2200 and vss >50

and <65.

Set Condition:

The oxygen sensor signal voltage is switching from below 0.39 volts to

above 0.58 volts and back fewer times than required.

77

DRIVEABILITY - GAS

POSSIBLE CAUSES

INTERMITTENT CONDITION

EXHAUST LEAK

O2 SENSOR SIGNAL CIRCUIT VOLTAGE DROP

O2 SENSOR GROUND CIRCUIT VOLTAGE DROP

O2 SENSOR

TEST

ACTION

APPLICABILITY

1

NOTE: Check for contaminates that may have damaged the O2 Sensor:
contaminated fuel, unapproved silicone, oil and coolant.
Turn the ignition on.
With the DRBIII

t, read DTC’s.

Is the Good Trip counter displayed and equal to zero?

All

Yes

Go To

2

No

Go To

6

2

Start the engine.
Inspect the exhaust for leak between the engine and the O2 sensor.
Inspect the exhaust for leaks between the engine and the appropriate rear O2 Sensor.
Are there any exhaust leaks?

All

Yes

Repair or replace the leaking exhaust parts as necessary.
Perform POWERTRAIN VERIFICATION TEST VER - 5.

No

Go To

3

3

NOTE: Ensure the voltmeter leads meet the terminals in the connector and
that there is good terminal to wire connection.
NOTE: Ensure the voltmeter leads are connected for positive polarity
Backprobe between the O2 Sensor Signal circuit at the O2 Sensor harness connector
and PCM harness connector.
Start the engine.
Allow the engine to idle.
Is the voltage below 0.10 volt?

All

Yes

Go To

4

No

Repair the high resistance on the O2 Sensor Signal circuit.
Perform POWERTRAIN VERIFICATION TEST VER - 5.

4

NOTE: Ensure the voltmeter leads meet the terminals in the connector and
that there is good terminal to wire connection.
NOTE: Ensure the voltmeter leads are connected for positive polarity
Backprobe between the O2 Sensor ground circuit at the O2 Sensor harness connector
and PCM harness connector.
Start the engine.
Allow the engine to idle.
Is the voltage below 0.10 volt?

All

Yes

Go To

5

No

Repair the high resistance on the O2 Sensor ground circuit.
Perform POWERTRAIN VERIFICATION TEST VER - 5.

78

DRIVEABILITY - GAS

P0133-1/1 O2 SENSOR SLOW RESPONSE —

Continued

TEST

ACTION

APPLICABILITY

5

If there are no possible causes remaining, view repair.

All

Repair

Replace the O2 Sensor
Perform POWERTRAIN VERIFICATION TEST VER - 5.

6

NOTE: Check for contaminates that may have damaged the O2 Sensor:
contaminated fuel, unapproved silicone, oil and coolant.
WARNING: KEEP CLEAR OF THE ENGINE’S MOVING PARTS.
NOTE: The conditions that set the DTC are not present at this time. The
following list may help in identifying the intermittent condition.
With the engine running at normal operating temperature, monitor the DRBIII

t

parameters related to the DTC while wiggling the wiring harness. Look for param-
eter values to change and/or a DTC to set.
Review the DRBIII

t Freeze Frame information. If possible, try to duplicate the

conditions under which the DTC was set.
Refer to any Technical Service Bulletins (TSB) that may apply.
Visually inspect the related wiring harness. Look for any chafed, pierced, pinched, or
partially broken wires.
Visually inspect the related wiring harness connectors. Look for broken, bent, pushed
out, or corroded terminals.
Were any of the above conditions present?

All

Yes

Repair as necessary
Perform POWERTRAIN VERIFICATION TEST VER - 5.

No

Test Complete.

79

DRIVEABILITY - GAS

P0133-1/1 O2 SENSOR SLOW RESPONSE —

Continued

Symptom List:

P0135-1/1 O2 SENSOR HEATER FAILURE
P0141-1/2 O2 SENSOR HEATER FAILURE
P0155-2/1 O2 SENSOR HEATER FAILURE
P0161-2/2 O2 SENSOR HEATER FAILURE

Test Note:

All symptoms listed above are diagnosed using the same tests.

The title for the tests will be P0135-1/1 O2 SENSOR HEATER
FAILURE.

When Monitored and Set Condition:

P0135-1/1 O2 SENSOR HEATER FAILURE

When Monitored:

With battery voltage greater than 9 volts, at a cold start, ECT less than

147°F, battery temperature sensor equal to or less than 27°F, and engine at idle for at least
12 seconds.

Set Condition:

O2 sensor voltage greater than 3 volts for 30 to 90 seconds.

P0141-1/2 O2 SENSOR HEATER FAILURE

When Monitored:

With battery voltage greater than 9 volts, at a cold start, ECT less than

147°F, battery temperature sensor equal to or less than 27°F, and engine at idle for at least
12 seconds.

Set Condition:

O2 sensor voltage greater than 3 volts for 60 to 240 seconds.

P0155-2/1 O2 SENSOR HEATER FAILURE

When Monitored:

With battery voltage greater than 9 volts, at a cold start, ECT less than

147°F, battery temperature sensor equal to or less than 27°F, and engine at idle for at least
12 seconds.

Set Condition:

O2 sensor voltage greater than 3 volts for 30 to 90 seconds.

P0161-2/2 O2 SENSOR HEATER FAILURE

When Monitored:

With battery voltage greater than 9 volts, at a cold start, ECT less than

147°F, battery temperature sensor equal to or less than 27°F, and engine at idle for at least
12 seconds.

Set Condition:

O2 sensor voltage greater than 3 volts for 30 to 90 seconds.

POSSIBLE CAUSES

O2 HEATER ELEMENT

O2 SENSOR HEATER GROUND CIRCUIT OPEN

O2 HEATER RELAY OUTPUT CIRCUIT OPEN

80

DRIVEABILITY - GAS

 

 

 

 

 

 

 

Content   ..  827  828  829  830   ..