Jeep XJ. Manual - part 596

 

  Index      Jeep     Jeep XJ - service repair manual 2001 year

 

Search            

 

 

 

 

 

 

 

 

 

Content   ..  594  595  596  597   ..

 

 

Jeep XJ. Manual - part 596

 

 

TEST

ACTION

APPLICABILITY

5

Turn the ignition off.
Disconnect the PCM C3 harness connector.
Measure the resistance of the SCI Transmit circuit between the PCM C3 connector
and the DLC.
Is the resistance below 5.0 ohms?

All

Yes

Go To

6

No

Repair the SCI Transmit circuit for an open.
Perform POWERTRAIN VERIFICATION TEST VER - 1.

6

If there are no possible causes remaining, view repair.

All

Repair

Replace the Powertrain Control Module.
Perform POWERTRAIN VERIFICATION TEST VER - 1.

36

COMMUNICATION

*NO RESPONSE FROM POWERTRAIN CONTROL MODULE (DIESEL
ONLY) —

Continued

Symptom:

P0115-TEMPERATURE OF ENGINE COOLANT SRC HIGH EX-
CEEDED

When Monitored and Set Condition:

P0115-TEMPERATURE OF ENGINE COOLANT SRC HIGH EXCEEDED

When Monitored:

With the ignition on.

Set Condition:

The voltage on the ECM engine coolant temperature sensor signal circuit

is above 4.9 volts for more than 3 seconds.

POSSIBLE CAUSES

INTERMITTENT CONDITION

ECM ECT SENSOR GROUND CIRCUIT OPEN

ECM ECT SENSOR SIGNAL CIRCUIT SHORTED TO VOLTAGE

ECM ECT SENSOR

ECM ECT SENSOR SIGNAL CIRCUIT OPEN

ENGINE CONTROL MODULE

TEST

ACTION

APPLICABILITY

1

Turn the ignition on.
With the DRB, monitor the ECM Engine Coolant Temperature (ECT) Sensor voltage.
Is the ECM ECT Sensor voltage above 4.5 volts?

All

Yes

Go To

2

No

Go To

7

2

Turn the ignition off.
Disconnect the ECM ECT Sensor harness connector.
Turn the ignition on.
Measure the voltage on the ECM ECT Sensor Signal circuit.
Is the voltage above 5.5 volts?

All

Yes

Repair the ECM ECT Sensor Signal circuit for a short to voltage.
Perform ROAD TEST VERIFICATION - VER-2.

No

Go To

3

3

Turn the ignition off.
Disconnect the ECM ECT Sensor harness connector.
Connect a jumper wire between the ECM ECT Sensor harness connector cavities.
Turn the ignition on.
With the DRB, read the ECM ECT Sensor voltage.
Is the voltage below 1.0 volt?

All

Yes

Replace the ECM ECT Sensor in accordance with the Service
Information.
Perform ROAD TEST VERIFICATION - VER-2.

No

Go To

4

37

DRIVEABILITY - DIESEL

TEST

ACTION

APPLICABILITY

4

Turn the ignition off.
Disconnect the ECM ECT Sensor harness connector.
Connect a jumper wire between ground and the ECM ECT Sensor Signal circuit.
Turn the ignition on.
With the DRB, read the ECM ECT Sensor voltage.
Is the voltage below 1.0 volt?

All

Yes

Repair the ECM ECT Sensor Ground circuit for an open.
Perform ROAD TEST VERIFICATION - VER-2.

No

Go To

5

5

Turn the ignition off.
Disconnect the ECM harness connectors.
Disconnect the ECM ECT Sensor harness connector.
Measure the resistance of the ECM ECT Sensor Signal circuit.
Is the resistance below 5.0 ohms?

All

Yes

Go To

6

No

Repair the ECM ECT Sensor Signal circuit for an open.
Perform ROAD TEST VERIFICATION - VER-2.

6

If there are no possible causes remaining, view repair.

All

Repair

Replace and program the Engine Control Module in accordance
with the Service Information.
Perform ROAD TEST VERIFICATION - VER-2.

7

WARNING: KEEP CLEAR OF THE ENGINE’S MOVING PARTS.
NOTE: The conditions that set the DTC are not present at this time. The
following list may help in identifying the intermittent condition.
With the engine running at normal operating temperature, monitor the DRB
parameters related to the DTC while wiggling the wiring harness. Look for param-
eter values to change and/or a DTC to set.
Review the DTC When Monitored and Set Conditions. If possible, try to duplicate the
conditions under which the DTC was set.
Refer to any Technical Service Bulletins (TSB) that may apply.
Visually inspect the related wiring harness. Look for any chafed, pierced, pinched, or
partially broken wires.
Visually inspect the related wiring harness connectors. Look for broken, bent, pushed
out, or corroded terminals.
Were any of the above conditions present?

All

Yes

Repair as necessary
Perform ROAD TEST VERIFICATION - VER-2.

No

Test Complete.

38

DRIVEABILITY - DIESEL

P0115-TEMPERATURE OF ENGINE COOLANT SRC HIGH EXCEEDED —

Continued

Symptom:

P0115-TEMPERATURE OF ENGINE COOLANT SRC LOW EX-
CEEDED

When Monitored and Set Condition:

P0115-TEMPERATURE OF ENGINE COOLANT SRC LOW EXCEEDED

When Monitored:

With the ignition on.

Set Condition:

The voltage on the ECM engine coolant temperature sensor signal circuit

is below 0.5 volt for more than 3 seconds.

POSSIBLE CAUSES

INTERMITTENT CONDITION

ECM ECT SENSOR

ECM ECT SENSOR SIGNAL CIRCUIT SHORTED TO GROUND

ECM ECT SENSOR SIGNAL AND GROUND CIRCUITS SHORTED TOGETHER

ENGINE CONTROL MODULE

TEST

ACTION

APPLICABILITY

1

Turn the ignition on.
With the DRB, monitor the ECM Engine Coolant Temperature (ECT) Sensor voltage.
Is the ECM ECT Sensor voltage below 0.3 volt?

All

Yes

Go To

2

No

Go To

6

2

Turn the ignition off.
Disconnect the ECM ECT Sensor harness connector.
Turn the ignition on.
With the DRB, read the ECM ECT Sensor voltage.
Is the voltage above 4.0 volts?

All

Yes

Replace the ECM ECT Sensor in accordance with the Service
Information.
Perform ROAD TEST VERIFICATION - VER-2.

No

Go To

3

3

Turn the ignition off.
Disconnect the ECM harness connectors.
Disconnect the ECM ECT Sensor harness connector.
Measure the resistance between ground and the ECM ECT Sensor Signal circuit.
Is the resistance above 100 kohms?

All

Yes

Go To

4

No

Repair the ECM ECT Sensor Signal circuit for a short to ground.
Perform ROAD TEST VERIFICATION - VER-2.

39

DRIVEABILITY - DIESEL

 

 

 

 

 

 

 

Content   ..  594  595  596  597   ..