Jeep XJ. Manual - part 593

 

  Index      Jeep     Jeep XJ - service repair manual 2001 year

 

Search            

 

 

 

 

 

 

 

 

 

Content   ..  591  592  593  594   ..

 

 

Jeep XJ. Manual - part 593

 

 

TEST

ACTION

APPLICABILITY

10

Turn the ignition off.
Disconnect the PCM harness connectors.
Disconnect the Generator Field harness connector.
Measure the resistance of the Generator Field Driver circuit.
Is the resistance below 5.0 ohms?

All

Yes

Go To

11

No

Repair the Generator Field Driver circuit for an open.
Perform CHARGING VERIFICATION - VER-3.

11

If there are no possible causes remaining, view repair.

All

Repair

Replace and program the Powertrain Control Module in accor-
dance with the Service Information.
Perform CHARGING VERIFICATION - VER-3.

24

CHARGING

P1682-CHARGING SYSTEM VOLTAGE TOO LOW - DIESEL —

Continued

Symptom:

P-1685 INVALID SKIM KEY

When Monitored and Set Condition:

P-1685 INVALID SKIM KEY

When Monitored:

With the ignition on.

Set Condition:

The PCM does not receive a valid key message from the SKIM.

POSSIBLE CAUSES

INCORRECT VIN IN PCM

INVALID SKIM KEY NOT PRESENT

NO COMMUNICATION WITH SKIM

NO VIN PROGRAMMED IN THE PCM

PCM

SKIM TROUBLE CODES SET

TEST

ACTION

APPLICABILITY

1

With the DRB III, read the PCM DTCs. Look for P1685.
Turn the ignition on.
Is the Starts Since Set counter for DTC P1685 displayed and equal to 0?

All

Yes

Go To

2

No

Go To

7

2

Turn the ignition on.
With the DRB III, attempt to communicate with the SKIM.
Can you communicate with the SKIM?

All

Yes

Go To

3

No

Refer to symptom BUS +/- SIGNAL OPEN FROM SKIM in the
COMMUNICATION category.
Perform ROAD TEST VERIFICATION - VER-2.

3

Turn the ignition on.
With the DRB III, check for SKIM DTC’s.
Are there any trouble codes set in the SKIM?

All

Yes

Repair all SKIM DTC’s.
Perform ROAD TEST VERIFICATION - VER-2.

No

Go To

4

25

COMMUNICATION

TEST

ACTION

APPLICABILITY

4

NOTE: If a VIN has not been programmed into the PCM, program VIN into
the PCM and retest.
Turn the ignition on.
With the DRB III, display the VIN that is programmed in the PCM.
Is there a VIN programmed in the PCM?

All

Yes

Go To

5

No

Program the correct VIN into the PCM and retest.
Perform ROAD TEST VERIFICATION - VER-2.

5

Turn the ignition on.
With the DRB III, display the VIN that is programmed in the PCM.
Is the correct VIN programmed in the PCM?

All

Yes

Go To

6

No

Replace and program the PCM in accordance with the Service
Information.
Perform ROAD TEST VERIFICATION - VER-2.

6

Turn the ignition off.
Replace and program the Sentry Key Immobilizer Module in accordance with the
Service Information.
Turn the ignition on.
With the DRB III, erase all DTCs.
Attempt to start and idle the engine.
With the DRB III, read the PCM DTCs.
Does the DRB III display this code?

All

Yes

Replace and program the Powertrain Control Module in accor-
dance with the Service Information.
Perform ROAD TEST VERIFICATION - VER-2.

No

Test Complete.

7

NOTE: This DTC could have been set if the SKIM harness connector was
disconnected, or if the SKIM was replaced recently.
NOTE: All keys that the customer uses for this vehicle must be tested to
verify they are operating properly.
Verify the correct VIN is programmed in both the PCM and SKIM modules.
Turn the ignition off.
With the next customer key turn the ignition key on and crank the engine to start.
With the DRB III, read the PCM DTCs. Look for P1685
Is the Starts Since Set Counter for DTC P1685 displayed and equal to 0?

All

Yes

Replace the Ignition Key.
Perform ROAD TEST VERIFICATION - VER-2.

No

Test Complete.

NOTE: If this DTC can not be reset, it may have been an actual theft attempt.

26

COMMUNICATION

P-1685 INVALID SKIM KEY —

Continued

Symptom:

P-1686 NO SKIM BUS MESSAGE RECEIVED

When Monitored and Set Condition:

P-1686 NO SKIM BUS MESSAGE RECEIVED

When Monitored:

With the ignition on.

Set Condition:

The PCM does not receive a CCD Bus message from the SKIM when

expected.

POSSIBLE CAUSES

PCM

INTERMITTENT CONDITION

CCD BUS CIRCUIT(S) OPEN FROM PCM TO SKIM

LOSS OF SKIM COMMUNICATION

TEST

ACTION

APPLICABILITY

1

Turn the ignition on.
With the DRB III, read PCM DTCs. LOOK for P1686.
Is the Starts Since Set counter for DTC P1686 displayed and equal to 0?

All

Yes

Go To

2

No

Go To

4

2

Turn the ignition on.
With the DRB III, attempt to communicate with the SKIM.
With the DRB III, select Theft Alarm and read the SKIM DTCs.
NOTE: This test will indicate if the Bus is operational from the DLC to the
SKIM.
Can the DRB communicate with the SKIM?

All

Yes

Go To

3

No

Refer to the appropriate symptom in the COMMUNICATION
category.
Perform ROAD TEST VERIFICATION - VER-2.

3

Turn the ignition off.
Disconnect the PCM harness connectors.
Disconnect the SKIM harness connector.
Measure the resistance of both CCD Bus circuits between the PCM and the SKIM.
Is the resistance below 5.0 ohms for each measurement?

All

Yes

Replace and program the Powertrain Control Module in accor-
dance with the Service Information.
Perform ROAD TEST VERIFICATION - VER-2.

No

Repair the CCD Bus circuit(s) for an open.
Perform ROAD TEST VERIFICATION - VER-2.

27

COMMUNICATION

 

 

 

 

 

 

 

Content   ..  591  592  593  594   ..