Jeep XJ. Manual - part 549

 

  Index      Jeep     Jeep XJ - service repair manual 2001 year

 

Search            

 

 

 

 

 

 

 

 

 

Content   ..  547  548  549  550   ..

 

 

Jeep XJ. Manual - part 549

 

 

TEST

ACTION

APPLICABILITY

3

Ensure the ignition key is off while disconnecting the following Modules.
Disconnect the following Components from the CCD Bus one at a time in an orderly
manner (be sure to turn the ignition off before disconnecting any Module). After
disconnecting, turn the ignition back on.
Observe the DRB Bus message for a change after each Module is disconnected which
will identify that module/circuits as being the cause of the Bus Failure Message.
Disconnect the TCM harness connector if equipped.
Disconnect the Overhead Console harness connector if equipped.
Remove the Instrument Cluster from the Instrument Panel.
Disconnect the RKE Module harness connector if equipped.
Disconnect the SKIM harness connector if equipped.
TURN IGNITION OFF, DISCONNECT THE BATTERY AND WAIT TWO MINUTES
BEFORE PROCEEDING.
Disconnect the ACM harness connector.
TURN IGNITION ON, THEN RECONNECT THE BATTERY.
Did the DRB Bus message change after disconnecting any one module/component?

All

Yes

Go To

4

No

Go To

5

4

Turn the ignition off.
Disconnect the harness connectors on the module that when disconnected the bus
failure message was eliminated.
Measure the resistance between the CCD Bus (+) circuit and each 5 volt circuit in the
harness connector.
Measure the resistance between the CCD Bus (-) circuit and each 5 volt circuit in the
harness connector.
Is the resistance below 100.0 ohms on any of the measurements?

All

Yes

Repair the CCD Bus circuit for a short to a 5 volt circuit.
Perform BODY VERIFICATION TEST - VER 1.

No

Replace the module/component that caused the bus failure mes-
sage.
Perform BODY VERIFICATION TEST - VER 1.

5

All modules must be disconnected from the CCD Bus circuit at this time.
Turn the ignition on.
Measure the CCD Bus (+) circuit and the CCD Bus (-) circuit at the Data Link
connector for voltage.
Is the voltage above 4.0 volts on either Bus circuit?

All

Yes

Repair the CCD Bus (+) or the CCD Bus (-) circuit for a short to
voltage.
Perform BODY VERIFICATION TEST - VER 1.

No

Go To

6

6

If there are no possible causes remaining, view repair.

All

Repair

Repair/Replace the DRB or DRB cable as necessary.
Perform BODY VERIFICATION TEST - VER 1.

76

COMMUNICATION

*SHORT TO 5 VOLTS FAILURE —

Continued

Symptom:

*SHORT TO BATTERY FAILURE

POSSIBLE CAUSES

POWERTRAIN CONTROL MODULE OPEN GROUND CIRCUITS

POWERTRAIN CONTROL MODULE - INTERNAL SHORT TO BATTERY

AIRBAG CONTROL MODULE

INSTRUMENT CLUSTER GROUND CIRCUIT OPEN

INSTRUMENT CLUSTER - INTERNAL SHORT TO BATTERY

SENTRY KEY IMMOBILIZER MODULE (IF EQUIPPED)

SENTRY KEY IMMOBILIZER MODULE GROUND CIRCUIT OPEN

SENTRY KEY IMMOBILIZER MODULE - INTERNAL SHORT TO BATTERY

REMOTE KEYLESS ENTRY MODULE GROUND CIRCUIT OPEN

REMOTE KEYLESS ENTRY MODULE - INTERNAL SHORT TO BATTERY

OVERHEAD CONSOLE GROUND CIRCUIT OPEN

OVERHEAD CONSOLE - INTERNAL SHORT TO BATTERY

TRANSMISSION CONTROL MODULE (IF EQUIPPED)

CCD BUS (+) OR BUS (-) CIRCUIT SHORTED TO BATTERY

DRB OR DRB CABLE

TEST

ACTION

APPLICABILITY

1

Turn the ignition off.
Disconnect the PCM C3 harness connector.
Turn the ignition on.
With the DRB, enter SYSTEM MONITORS then CCD Bus Test.
Does the DRB display: SHORT TO BATTERY?

All

Yes

Go To

2

No

Go To

13

2

TURN THE IGNITION OFF, DISCONNECT THE BATTERY AND WAIT TWO
MINUTES BEFORE PROCEEDING.
Disconnect the ACM harness connector.
TURN THE IGNITION ON, THEN RECONNECT THE BATTERY.
With the DRB, enter SYSTEM MONITORS then CCD Bus Test.
Does the DRB display: SHORT TO BATTERY?

All

Yes

Go To

3

No

Replace the Airbag Control Module.
Perform BODY VERIFICATION TEST - VER 1.

77

COMMUNICATION

TEST

ACTION

APPLICABILITY

3

Turn the ignition off.
Disconnect the Instrument Cluster C2 harness connector.
Turn the ignition on.
With the DRB, enter SYSTEM MONITORS then CCD Bus Test.
Does the DRB display: SHORT TO BATTERY?

All

Yes

Go To

4

No

Go To

12

4

NOTE: Answer Yes to the question if the vehicle is not equipped with this
module.
Turn the ignition off.
Disconnect the SKIM harness connector.
Turn the ignition on.
With the DRB, enter SYSTEM MONITORS then CCD Bus Test.
Does the DRB display: SHORT TO BATTERY?

All

Yes

Go To

5

No

Go To

11

5

NOTE: Answer Yes to the question if the vehicle is not equipped with this
module.
Turn the ignition off.
Disconnect the RKE Module harness connector.
Turn the ignition on.
With the DRB, enter SYSTEM MONITORS then CCD Bus Test.
Does the DRB display: SHORT TO BATTERY?

All

Yes

Go To

6

No

Go To

10

6

NOTE: Answer Yes to the question if the vehicle is not equipped with this
module.
Turn the ignition off.
Disconnect the Overhead Console harness connector.
Turn the ignition on.
With the DRB, enter SYSTEM MONITORS then CCD Bus Test.
Does the DRB display: SHORT TO BATTERY?

All

Yes

Go To

7

No

Go To

9

7

NOTE: Answer Yes to the question if the vehicle is not equipped with this
module.
Turn the ignition off.
Disconnect the TCM harness connector.
Turn the ignition on.
With the DRB, enter SYSTEM MONITORS then CCD Bus Test.
Does the DRB display: SHORT TO BATTERY?

All

Yes

Go To

8

No

Replace the Transmission Control Module.
Perform BODY VERIFICATION TEST - VER 1.

78

COMMUNICATION

*SHORT TO BATTERY FAILURE —

Continued

TEST

ACTION

APPLICABILITY

8

Turn the ignition off.
Disconnect the PCM C3 harness connector.
Disconnect the ACM harness connector.
Disconnect the Instrument Cluster C2 harness connector.
Disconnect the SKIM harness connector (If equipped).
Disconnect the RKE Module harness connector (If equipped).
Disconnect the Overhead Console harness connector (If equipped).
Disconnect the TCM harness connector (If equipped).
Turn the ignition on.
Measure the voltage of the CCD Bus (+) and the CCD Bus (-) circuits at the DLC.
Is the voltage above 0.5 volts?

All

Yes

Repair the CCD Bus (+) or CCD Bus (-) circuit for a short to
battery.
Perform BODY VERIFICATION TEST - VER 1.

No

Repair/replace the DRB or DRB cable as necessary.
Perform BODY VERIFICATION TEST - VER 1.

9

Turn the ignition off.
Disconnect the Overhead Console harness connector.
Turn all lights off.
Measure the resistance between ground and the Ground circuit (cavity 12).
Is the resistance below 5.0 ohms?

All

Yes

Replace the Compass Mini Trip Computer (Overhead Console).
Perform BODY VERIFICATION TEST - VER 1.

No

Repair the Ground circuit for an open.
Perform BODY VERIFICATION TEST - VER 1.

10

Turn the ignition off.
Disconnect the RKE module harness connector.
Turn all lights off.
Measure the resistance between ground and the Ground circuit in the RKE Module
connector.
Is the resistance below 5.0 ohms?

All

Yes

Replace the Remote Keyless Entry Module.
Perform BODY VERIFICATION TEST - VER 1.

No

Repair the Ground circuit for an open.
Perform BODY VERIFICATION TEST - VER 1.

11

Turn the ignition off.
Disconnect the SKIM harness connector.
Turn all lights off.
Measure the resistance between ground and both Ground circuits in the SKIM
connector.
Is the resistance below 5.0 ohms for each measurement?

All

Yes

Replace the Sentry Key Immobilizer Module.
Perform BODY VERIFICATION TEST - VER 1.

No

Repair the Ground circuit for an open.
Perform BODY VERIFICATION TEST - VER 1.

79

COMMUNICATION

*SHORT TO BATTERY FAILURE —

Continued

 

 

 

 

 

 

 

Content   ..  547  548  549  550   ..