Jeep Wrangler TJ. Manual - part 439

 

  Index      Jeep     Jeep Wrangler TJ - service repair manual 2005 year

 

Search            

 

 

 

 

 

 

 

 

 

Content   ..  437  438  439  440   ..

 

 

Jeep Wrangler TJ. Manual - part 439

 

 

DIAGNOSIS AND TESTING

DIAGNOSIS AND TESTING - ENGINE
DIAGNOSIS - INTRODUCTION

Engine diagnosis is helpful in determining the

causes of malfunctions not detected and remedied by
routine maintenance.

These malfunctions may be classified as either per-

formance (e.g., engine idles rough and stalls) or
mechanical (e.g., a strange noise).

(Refer to 9 - ENGINE - DIAGNOSIS AND TEST-

ING) (PERFORMANCE) or (Refer to 9 - ENGINE -

DIAGNOSIS AND TESTING) (MECHANICAL) for
possible causes and corrections of malfunctions.

Additional tests and diagnostic procedures may be

necessary for specific engine malfunctions that can
not be isolated with the Service Diagnosis charts.
Information concerning additional tests and diagno-
sis is provided within the following diagnosis:

• (Refer to 9 - ENGINE - DIAGNOSIS AND

TESTING) (PERFORMANCE)

• (Refer to 9 - ENGINE - DIAGNOSIS AND

TESTING) (MECHANICAL)

DIAGNOSIS AND TESTING - ENGINE DIAGNOSIS - PERFORMANCE

ENGINE PERFORMANCE DIAGNOSIS CHART

CONDITION

POSSIBLE CAUSES

CORRECTION

ENGINE WILL NOT CRANK

1. Weak or dead battery

1. Charge/Replace Battery. (Refer to
8 - ELECTRICAL/BATTERY
SYSTEM/BATTERY - STANDARD
PROCEDURE), for correct
procedures. Check charging system.
(Refer to 8 - ELECTRICAL/
CHARGING - DIAGNOSIS AND
TESTING), for correct procedures.

2. Corroded or loose battery
connections

2. Clean/tighten suspect battery/
starter connections

3. Faulty starter or related circuit(s)

3. Check starting system. (Refer to
8 - ELECTRICAL/STARTING -
DIAGNOSIS AND TESTING), for
correct diagnostics/procedures

4. Siezed accessory drive
component

4. Remove accessory drive belt and
attempt to start engine. If engine
starts, repair/replace siezed
component.

5. Engine internal mechanical
failure or hydro-static lock

5. (Refer to 9 - ENGINE -
DIAGNOSIS AND TESTING), for
correct diagnostics/procedures

TJ

ENGINE 4.0L

9 - 71

ENGINE 4.0L (Continued)

CONDITION

POSSIBLE CAUSES

CORRECTION

ENGINE CRANKS BUT WILL NOT
START

1. No spark

1. Check for spark. (Refer to 8 -
ELECTRICAL/IGNITION CONTROL
- SPECIFICATIONS), for correct
procedures.

2. No fuel

2. Perform fuel pressure test (Refer
to 14 - FUEL SYSTEM/FUEL
DELIVERY/FUEL PUMP -
DIAGNOSIS AND TESTING), and if
necessary, inspect fuel injector(s)
and driver circuits. (Refer to 14 -
FUEL SYSTEM/FUEL INJECTION/
FUEL INJECTOR - DIAGNOSIS
AND TESTING), for correct
procedures.

3. Low or no engine compression

3. Perform cylinder compression
pressure test. (Refer to 9 - ENGINE
- DIAGNOSIS AND TESTING).

ENGINE LOSS OF POWER

1. Worn or burned distributor rotor

1. Install new distributor rotor

2. Worn camshaft position sensor
shaft

2. Remove and repair camshaft
position sensor. (Refer to 8 -
ELECTRICAL/IGNITION CONTROL/
CAMSHAFT POSITION SENSOR -
REMOVAL).

3. Worn or incorrect gapped spark
plugs

3. Clean plugs and set gap. (Refer
to 8 - ELECTRICAL/IGNITION
CONTROL/SPARK PLUG -
CLEANING).

4. Dirt or water in fuel system

4. Clean system and replace fuel
filter

5. Faulty fuel pump

5. Install new fuel pump

6. Incorrect valve timing

6. Correct valve timing

7. Blown cylinder head gasket

7. Install new cylinder head gasket

8. Low compression

8. Test cylinder compression. (Refer
to 9 - ENGINE - DIAGNOSIS AND
TESTING).

9. Burned, warped, or pitted valves

9. Install/Reface valves as
necessary

10. Plugged or restricted exhaust
system

10. Install new parts as necessary

11. Faulty ignition coil rail

11. Test and replace, as necessary.
(Refer to 8 - ELECTRICAL/
IGNITION CONTROL/COIL RAIL -
REMOVAL).

ENGINE STALLS OR ROUGH IDLE

1. Carbon build-up on throttle plate

1. Remove throttle body and
de-carbon. (Refer to 14 - FUEL
SYSTEM/FUEL INJECTION/
THROTTLE BODY - REMOVAL) for
correct procedure.

9 - 72

ENGINE 4.0L

TJ

ENGINE 4.0L (Continued)

CONDITION

POSSIBLE CAUSES

CORRECTION

2. Engine idle speed too low

2. Check Idle Air Control circuit.

3. Worn or incorrectly gapped spark
plugs

3. Replace or clean and re-gap
spark plugs. (Refer to 8 -
ELECTRICAL/IGNITION CONTROL/
SPARK PLUG - CLEANING)

4. Faulty coil rail

4. Test and replace, if necessary.
(Refer to 8 - ELECTRICAL/
IGNITION CONTROL/COIL RAIL -
REMOVAL)

5. Intake manifold vacuum leak

5. Inspect intake manifold gasket
and vacuum hoses. Replace if
necessary. (Refer to 9 - ENGINE/
MANIFOLDS/INTAKE MANIFOLD -
DIAGNOSIS AND TESTING).

ENGINE MISSES ON
ACCELERATION

1. Worn or incorrectly gapped spark
plugs

1. Replace spark plugs or clean and
set gap.

2. Spark plug cables defective or
crossed

2. Replace spark plug cables.

3. Dirt in fuel system

3. Clean fuel system

4. Burned, warped or pitted valves

4. Install new valves

5. Faulty coil rail

5. Test and replace as necessary.
(Refer to 8 - ELECTRICAL/
IGNITION CONTROL/COIL RAIL -
REMOVAL)

TJ

ENGINE 4.0L

9 - 73

ENGINE 4.0L (Continued)

DIAGNOSIS AND TESTING - ENGINE DIAGNOSIS - MECHANICAL

ENGINE MECHANICAL DIAGNOSIS CHART

CONDITION

POSSIBLE CAUSES

CORRECTION

NOISY VALVES/LIFTERS

1. High or low oil level in crankcase

1. Check for correct oil level. Adjust
oil level by draining or adding as
needed

2. Thin or diluted oil

2. Change oil. (Refer to 9 -
ENGINE/LUBRICATION/OIL -
STANDARD PROCEDURE)

3. Low oil pressure

3. Check engine oil level. If ok,
Perform oil pressure test. (Refer to
9 - ENGINE/LUBRICATION -
DIAGNOSIS AND TESTING) for
engine oil pressure test/
specifications

4. Dirt in tappets/lash adjusters

4. Clean/replace hydraulic
tappets/lash adjusters

5. Bent push rod(s)

5. Install new push rods

6. Worn rocker arms

6. Inspect oil supply to rocker arms
and replace worn arms as needed

7. Worn tappets/lash adjusters

7. Install new hydraulic tappets/lash
adjusters

8. Worn valve guides

8. Inspect all valve guides and
replace as necessary

9. Excessive runout of valve seats
or valve faces

9. Grind valves and seats

CONNECTING ROD NOISE

1. Insufficient oil supply

1. Check engine oil level.

2. Low oil pressure

2. Check engine oil level. If ok,
Perform oil pressure test. (Refer to
9 - ENGINE/LUBRICATION -
DIAGNOSIS AND TESTING) engine
oil pressure test/specifications

3. Thin or diluted oil

3. Change oil to correct viscosity.
(Refer to 9 - ENGINE/
LUBRICATION/OIL - STANDARD
PROCEDURE) for correct
procedure/engine oil specifications

4. Excessive connecting rod
bearing clearance

4. Measure bearings for correct
clearance with plasti-gage. Repair
as necessary

5. Connecting rod journal out of
round

5. Replace crankshaft or grind
journals

6. Misaligned connecting rods

6. Replace bent connecting rods

9 - 74

ENGINE 4.0L

TJ

ENGINE 4.0L (Continued)

 

 

 

 

 

 

 

Content   ..  437  438  439  440   ..