Jeep Wrangler TJ. Manual - part 176

 

  Index      Jeep     Jeep Wrangler TJ - service repair manual 2005 year

 

Search            

 

 

 

 

 

 

 

 

 

Content   ..  174  175  176  177   ..

 

 

Jeep Wrangler TJ. Manual - part 176

 

 

TEST

ACTION

APPLICABILITY

9

Turn the ignition off to the lock position.
Disconnect the Transmission TRS harness connector.
Ignition on, engine not running.
Using a 12-volt test light connected to ground, check the Fused Ignition Switch
Output circuit in the TRS harness connector.
NOTE: The test light must illuminate brightly. Compare the brightness to
that of a direct connection to the battery.
Does the test light illuminate brightly?

All

Yes

→ Go To 10

No

→ Repair the Fused Ignition Switch Output circuit for an open. If

the fuse is open make sure to check for a short to ground.
Perform TRANSMISSION NO TROUBLE CODE VERIFICA-
TION TEST.

10

Turn ignition off to the lock position.
Remove the Backup Lamp bulb.
Disconnect the Transmission TRS harness connector.
Note: Check connectors - Clean/repair as necessary.
Measure the resistance between ground and the Backup Lamp Supply circuit.
Is the resistance below 5.0 ohms?

All

Yes

→ Repair Backup Lamp Supply circuit for a short to ground. Check

the fuse and replace if necessary.
Perform TRANSMISSION NO TROUBLE CODE VERIFICA-
TION TEST.

No

→ Test Complete.

429

TRANSMISSION - 42RLE

*BACKUP LAMPS INOPERATIVE —

Continued

Symptom:

*CHECKING PARK/NEUTRAL SWITCH OPERATION

POSSIBLE CAUSES

P/N POSITION SWITCH SENSE CIRCUIT OPEN

P/N POSITION SWITCH SENSE CIRCUIT SHORTED TO GROUND

TRANSMISSION RANGE SENSOR

PCM - P/N POSITION SWITCH

TEST

ACTION

APPLICABILITY

1

Turn the ignition on.
With the DRBIII

t, read the Park/Neutral Position Switch input state.

While moving the gear selector through all gear positions, Park to 1 and back to Park,
watch the DRBIII

t display.

Did the DRBIII

t display show P/N and D/R in the correct gear positions?

All

Yes

→ Test Complete.

No

→ Go To 2

2

Turn the ignition off.
Disconnect the PCM harness connectors.
Disconnect the Transmission Range Sensor harness connector.
Note: Check connectors - Clean/repair as necessary.
Measure the resistance of the P/N Position Switch Sense circuit.
Is the resistance below 5.0 ohms?

All

Yes

→ Go To 3

No

→ Repair the P/N Position Switch Sense circuit for an open.

Perform TRANSMISSION NO TROUBLE CODE VERIFICA-
TION TEST.

3

Turn the ignition off.
Disconnect the PCM harness connectors.
Disconnect the Transmission Range Sensor harness connector.
Note: Check connectors - Clean/repair as necessary.
Measure the resistance between ground and the P/N Position Switch Sense circuit.
Is the resistance above 100k ohms?

All

Yes

→ Go To 4

No

→ Repair the P/N Position Switch Sense circuit for a short to ground.

Perform TRANSMISSION NO TROUBLE CODE VERIFICA-
TION TEST.

430

TRANSMISSION - 42RLE

TEST

ACTION

APPLICABILITY

4

Turn the ignition off.
Disconnect the PCM harness connectors.
Move the Gear selector through all gear positions, from Park to 1st and back.
While moving the gear selector through each gear, measure the resistance between
ground and the P/N Position Switch Sense circuit.
Did the resistance change from above 10.0 ohms to below 10.0 ohms?

All

Yes

→ Go To 5

No

→ Replace the Transmission Range Sensor.

Perform TRANSMISSION NO TROUBLE CODE VERIFICA-
TION TEST.

5

If there are no possible causes remaining, view repair.

All

Repair

Replace and program the Powertrain Control Module per the
Service Information.
Perform POWERTRAIN VERIFICATION TEST VER - 2.

431

TRANSMISSION - 42RLE

*CHECKING PARK/NEUTRAL SWITCH OPERATION —

Continued

Symptom:

*INCORRECT TRANSMISSION FLUID LEVEL

POSSIBLE CAUSES

INCORRECT FLUID LEVEL

TEST

ACTION

APPLICABILITY

1

The transmission must be above 70 degree F. prior to checking fluid level. Adjusting
fluid level on a cold transmission will result in an overfilled transmission.
Check the transmission fluid level per the service information.
Is the fluid level OK?

All

Yes

→ Test Complete.

No

→ Adjust fluid level. Repair cause of incorrect fluid level.

Perform TRANSMISSION NO TROUBLE CODE VERIFICA-
TION TEST.

432

TRANSMISSION - 42RLE

 

 

 

 

 

 

 

Content   ..  174  175  176  177   ..