Jeep Wrangler TJ. Manual - part 157

 

  Index      Jeep     Jeep Wrangler TJ - service repair manual 2005 year

 

Search            

 

 

 

 

 

 

 

 

 

Content   ..  155  156  157  158   ..

 

 

Jeep Wrangler TJ. Manual - part 157

 

 

Symptom:

P0755-2/4 SOLENOID CIRCUIT

When Monitored and Set Condition:

P0755-2/4 SOLENOID CIRCUIT

When Monitored:

Initially at power-up, then every 10 seconds thereafter. They will also

be tested immediately after a Gear Ratio or Pressure Switch error is detected.

Set Condition:

Three consecutive Solenoid continuity test failures, or one failure if test is

run in response to a Gear Ratio or Pressure Switch error.

POSSIBLE CAUSES

RELATED RELAY DTC’S PRESENT

TRANSMISSION CONTROL RELAY OUTPUT CIRCUIT OPEN

2/4 SOLENOID CONTROL CIRCUIT OPEN

2/4 SOLENOID CONTROL CIRCUIT SHORT TO GROUND

2/4 SOLENOID CONTROL CIRCUIT SHORT TO VOLTAGE

2/4 SOLENOID

TRANSMISSION CONTROL MODULE

INTERMITTENT WIRING AND CONNECTORS

TEST

ACTION

APPLICABILITY

1

NOTE: Low fluid level can be the cause of many Transmission problems. If
the fluid level is low, locate and repair the leak, then check and adjust the
fluid level per the Service Information.
NOTE: Always perform diagnostics with a fully charged battery to avoid
false symptoms.
With the DRBIII

t, read the engine DTC’s. Check and repair all engine DTC’s prior

to performing Transmission Symptom Diagnostics.
With the DRBIII

t, read Transmission DTC’s. Record all DTC’s and 1 Trip Failures.

NOTE: Diagnose 1 Trip Failures as a fully matured DTC.
Using the wiring diagram/schematic as a guide, inspect the wiring and connectors.
Repair as necessary.
Perform the Shift Lever Position Test. If the test does not pass, refer to Symptom test
for P0706 Check Shifter Signal.
For Gear Ratio DTC’s, check and record all CVI’s.
Most DTC’s set on start up but some must be set by driving the vehicle such that all
diagnostic monitors have run.
NOTE: Verify flash level of Transmission Control Module. Some problems
are corrected by software upgrades to the Transmission Control Module.
NOTE: Check for applicable TSB’s related to the symptom.
Perform this procedure prior to Symptom diagnosis.

All

Continue

Go To

2

353

TRANSMISSION - 42RLE

TEST

ACTION

APPLICABILITY

2

With the DRBIII

t, read Transmission Control Module DTC’s

Are there any Transmission Control Relay DTC’s present?.

All

Yes

→ Refer to symptom list and perform the appropriate symptom for

Transmission Control Relay related DTC’s.
Perform 42RLE TRANSMISSION VERIFICATION TEST - VER
1.

No

→ Go To 3

3

With the DRBIII

t, Check the STARTS SINCE SET counter.

NOTE: This counter only applies to the last DTC set.
Is the STARTS SINCE SET counter for P0755 set at 0?

All

Yes

→ Go To 4

No

→ Go To 11

4

Turn the ignition off to the lock position.
CAUTION: Remove the Starter Relay from the PDC. This will prevent the
vehicle from being started in gear.
Install the Transmission Simulator, Miller tool #8333 and the Electronic Transmis-
sion Adapter kit 8333-1A.
Ignition on, engine not running.
With the DRBIII

t, actuate the 2/4 Solenoid.

With the Transmission Simulator, monitor the 2/4 Solenoid LED.
Did the 2/4 Solenoid LED on the Transmission Simulator blink on and off during
actuation?

All

Yes

→ Go To 5

No

→ Go To 6

5

If there are no possible causes remaining, view repair.

All

Repair

Replace the Transmission Solenoid/Pressure Switch Assembly per
the Service Information.
Perform 42RLE TRANSMISSION VERIFICATION TEST - VER
1.

6

Turn the ignition off to the lock position.
Disconnect the TCM harness connector.
Disconnect the Transmission Solenoid/Pressure Switch Assembly harness connector.
Note: Check connectors - Clean/repair as necessary.
Measure the resistance of the 2/4 Solenoid Control circuit from the TCM harness
connector to the Transmission Solenoid/Pressure Switch Assembly harness connec-
tor.
Is the resistance above 5.0 ohms?

All

Yes

→ Repair the 2/4 Solenoid Control circuit for an open.

Perform 42RLE TRANSMISSION VERIFICATION TEST - VER
1.

No

→ Go To 7

354

TRANSMISSION - 42RLE

P0755-2/4 SOLENOID CIRCUIT —

Continued

TEST

ACTION

APPLICABILITY

7

Turn the ignition off to the lock position.
Disconnect the TCM harness connector.
Disconnect the Transmission Solenoid/Pressure Switch Assembly harness connector.
Note: Check connectors - Clean/repair as necessary.
Measure the resistance between ground and the 2/4 Solenoid Control circuit.
Is the resistance below 5.0 ohms?

All

Yes

→ Repair the 2/4 Solenoid Control circuit for a short to ground.

Perform 42RLE TRANSMISSION VERIFICATION TEST - VER
1.

No

→ Go To 8

8

Turn the ignition off to the lock position.
Disconnect the TCM harness connector.
Disconnect the Transmission Solenoid/Pressure Switch Assembly harness connector.
Remove the Transmission Control Relay from the PDC.
Note: Check connectors - Clean/repair as necessary.
Connect a jumper wire between the Fused B+ circuit and Transmission Control Relay
Output circuit in the Transmission Control Relay connector in the PDC.
Ignition on, engine not running.
Measure the voltage of the 2/4 Solenoid Control circuit.
Is the voltage above 0.5 volt?

All

Yes

→ Repair the 2/4 Solenoid Control circuit for a short to voltage.

Perform 42RLE TRANSMISSION VERIFICATION TEST - VER
1.

No

→ Go To 9

9

Turn the ignition off to the lock position.
Disconnect the Transmission Solenoid/Pressure Switch Assembly harness connector.
Remove the Transmission Control Relay from the PDC.
Note: Check connectors - Clean/repair as necessary.
Connect a jumper wire between the Fused B+ circuit and the Transmission Control
Relay Output circuit in the Transmission Control Relay connector.
Ignition on, engine not running.
Using a 12-volt test light connected to ground, check the Transmission Control Relay
Output circuit.
NOTE: The test light must illuminate brightly. Compare the brightness to
that of a direct connection to the battery.
Does the test light illuminate brightly?

All

Yes

→ Go To 10

No

→ Repair the Transmission Control Relay Output circuit for an open

or high resistance.
Perform 42RLE TRANSMISSION VERIFICATION TEST - VER
1.

10

Using the schematics as a guide, inspect the wiring and connectors. Repair as
necessary. Pay particular attention to all power and ground circuits.
If there are no possible causes remaining, view repair.

All

Repair

Replace the Transmission Control Module per the Service Infor-
mation. WITH THE DRBIII

t PERFORM QUICK LEARN.

Perform 42RLE TRANSMISSION VERIFICATION TEST - VER
1.

355

TRANSMISSION - 42RLE

P0755-2/4 SOLENOID CIRCUIT —

Continued

TEST

ACTION

APPLICABILITY

11

The conditions necessary to set this DTC are not present at this time.
Using the schematics as a guide, inspect the wiring and connectors specific to this
circuit.
Wiggle the wiring while checking for shorts and open circuits.
With the DRBIII

t, check the EATX EVENT DATA to help identify the conditions in

which the DTC was set.
Were there any problems found?

All

Yes

→ Repair as necessary.

Perform 42RLE TRANSMISSION VERIFICATION TEST - VER
1.

No

→ Test Complete.

356

TRANSMISSION - 42RLE

P0755-2/4 SOLENOID CIRCUIT —

Continued

 

 

 

 

 

 

 

Content   ..  155  156  157  158   ..