Jeep Wrangler TJ. Manual - part 152

 

  Index      Jeep     Jeep Wrangler TJ - service repair manual 2005 year

 

Search            

 

 

 

 

 

 

 

 

 

Content   ..  150  151  152  153   ..

 

 

Jeep Wrangler TJ. Manual - part 152

 

 

TEST

ACTION

APPLICABILITY

7

Using the schematics as a guide, inspect the wiring and connectors. Repair as
necessary. Pay particular attention to all power and ground circuits.
If there are no possible causes remaining, view repair.

All

Repair

Replace the Transmission Control Module per the Service Infor-
mation. WITH THE DRBIII

t PERFORM QUICK LEARN.

Perform 42RLE TRANSMISSION VERIFICATION TEST - VER
1.

8

The conditions necessary to set the DTC are not present at this time. Using the
schematics as a guide, inspect the wiring and connectors specific to this circuit.
Wiggle the wires while checking for shorts and open circuits.
Check the power and ground circuits of the Transmission Control Module.
Check the vehicles battery condition.
Were any problems found?

All

Yes

→ Repair wiring and/or connectors as necessary.

Perform 42RLE TRANSMISSION VERIFICATION TEST - VER
1.

No

→ Test Complete.

333

TRANSMISSION - 42RLE

P0725-ENGINE SPEED SENSOR CIRCUIT —

Continued

Symptom:

P0731-GEAR RATIO ERROR IN 1ST

When Monitored and Set Condition:

P0731-GEAR RATIO ERROR IN 1ST

When Monitored:

The Transmission Gear Ratio is monitored continuously while the

Transmission is in gear.

Set Condition:

If the ratio of the input RPM to the output RPM does not match the

current Gear Ratio.

POSSIBLE CAUSES

RELATED DTC’S PRESENT

INTERMITTENT GEAR RATIO ERRORS

INTERNAL TRANSMISSION

TEST

ACTION

APPLICABILITY

1

NOTE: Low fluid level can be the cause of many Transmission problems. If
the fluid level is low, locate and repair the leak, then check and adjust the
fluid level per the Service Information.
NOTE: Always perform diagnostics with a fully charged battery to avoid
false symptoms.
With the DRBIII

t, read the engine DTC’s. Check and repair all engine DTC’s prior

to performing Transmission Symptom Diagnostics.
With the DRBIII

t, read Transmission DTC’s. Record all DTC’s and 1 Trip Failures.

NOTE: Diagnose 1 Trip Failures as a fully matured DTC.
Using the wiring diagram/schematic as a guide, inspect the wiring and connectors.
Repair as necessary.
Perform the Shift Lever Position Test. If the test does not pass, refer to Symptom test
for P0706 Check Shifter Signal.
For Gear Ratio DTC’s, check and record all CVI’s.
Most DTC’s set on start up but some must be set by driving the vehicle such that all
diagnostic monitors have run.
NOTE: Verify flash level of Transmission Control Module. Some problems
are corrected by software upgrades to the Transmission Control Module.
NOTE: Check for applicable TSB’s related to the symptom.
Perform this procedure prior to Symptom diagnosis.

All

Continue

Go To

2

2

With the DRBIII

t, read Transmission DTC’s

If any of these DTC’s are present, perform their respective tests first.
Are the DTC’s P0944, P0715, P0720, or P1794 present also?

All

Yes

→ Refer to the Transmission category and perform the appropriate

symptom. If any of these DTC’s are present, they will cause a gear
ratio error. Perform the test for Loss of Prime first if it is present.
Perform 42RLE TRANSMISSION VERIFICATION TEST - VER
1.

No

→ Go To 3

334

TRANSMISSION - 42RLE

TEST

ACTION

APPLICABILITY

3

With the DRBIII

t, perform the 1st Gear Clutch Test. Follow the instructions on the

DRBIII

t.

Increase the throttle angle, TPS Degree, to 30° for no more than a few seconds.
CAUTION: Do not overheat the transmission.
Did the Clutch Test pass, Input Speed remain at 0?

All

Yes

→ Go To 4

No

→ Go To 5

4

The conditions to set this DTC are not present at this time.
Check the gearshift linkage adjustment.
Gear ratio DTC’s can be set by problems in the Input and Output Speed Sensor
circuits. If the vehicle passes the clutch test and still sets gear ratio DTC(’s), check
the Speed Sensors for proper operation.
NOTE: Remove the Starter Relay from the PDC. This will prevent the
vehicle from being started in gear.
Check the Speed Sensor wiring and connectors for good connection, then perform a
wiggle test using the Transmission Simulator, Miller tool #8333 and the Electronic
Transmission Adapter kit 8333-1A.
This DTC can also be set under extreme temperature conditions, this is usually
caused by an internal problem. Verify if the problem is only experienced under
extreme hot or cold conditions.
With the DRBIII

t, check the EATX EVENT DATA to help identify the conditions in

which the DTC was set.
Were there any problems found?

All

Yes

→ Repair as necessary.

Perform 42RLE TRANSMISSION VERIFICATION TEST - VER
1.

No

→ Test Complete.

5

If there are no possible causes remaining, view repair.

All

Repair

Repair internal transmission per the Service Information. Check
all components related to the Underdrive and L/R clutches.
Inspect the Oil Pump per the Service Information and repair or
replace as necessary.
Perform 42RLE TRANSMISSION VERIFICATION TEST - VER
1.

335

TRANSMISSION - 42RLE

P0731-GEAR RATIO ERROR IN 1ST —

Continued

Symptom:

P0732-GEAR RATIO ERROR IN 2ND

When Monitored and Set Condition:

P0732-GEAR RATIO ERROR IN 2ND

When Monitored:

The Transmission Gear Ratio is monitored continuously while the

Transmission is in Gear.

Set Condition:

If the ratio of the input RPM to the output RPM does not match the

current Gear Ratio.

POSSIBLE CAUSES

RELATED DTC’S PRESENT

RELATED PRESSURE SWITCH DTC’S PRESENT

INTERMITTENT GEAR RATIO ERRORS

TRANSMISSION - INTERNAL

TEST

ACTION

APPLICABILITY

1

NOTE: Low fluid level can be the cause of many Transmission problems. If
the fluid level is low, locate and repair the leak, then check and adjust the
fluid level per the Service Information.
NOTE: Always perform diagnostics with a fully charged battery to avoid
false symptoms.
With the DRBIII

t, read the engine DTC’s. Check and repair all engine DTC’s prior

to performing Transmission Symptom Diagnostics.
With the DRBIII

t, read Transmission DTC’s. Record all DTC’s and 1 Trip Failures.

NOTE: Diagnose 1 Trip Failures as a fully matured DTC.
Using the wiring diagram/schematic as a guide, inspect the wiring and connectors.
Repair as necessary.
Perform the Shift Lever Position Test. If the test does not pass, refer to Symptom test
for P0706 Check Shifter Signal.
For Gear Ratio DTC’s, check and record all CVI’s.
Most DTC’s set on start up but some must be set by driving the vehicle such that all
diagnostic monitors have run.
NOTE: Verify flash level of Transmission Control Module. Some problems
are corrected by software upgrades to the Transmission Control Module.
NOTE: Check for applicable TSB’s related to the symptom.
Perform this procedure prior to Symptom diagnosis.

All

Continue

Go To

2

336

TRANSMISSION - 42RLE

 

 

 

 

 

 

 

Content   ..  150  151  152  153   ..