Jeep Wrangler TJ. Manual - part 128

 

  Index      Jeep     Jeep Wrangler TJ - service repair manual 2005 year

 

Search            

 

 

 

 

 

 

 

 

 

Content   ..  126  127  128  129   ..

 

 

Jeep Wrangler TJ. Manual - part 128

 

 

Symptom:

P0645-A/C CLUTCH RELAY CIRCUIT

When Monitored and Set Condition:

P0645-A/C CLUTCH RELAY CIRCUIT

When Monitored:

With the ignition on. Battery voltage greater than 10 volts. A/C Switch

on.

Set Condition:

An open or shorted condition is detected in the A/C clutch relay control

circuit. The desired A/C state does not equal the actual A/C clutch relay state. Three good
trips to clear the MIL.

POSSIBLE CAUSES

A/C CLUTCH RELAY OPERATION

(F960) FUSED IGNITION SWITCH OUTPUT CIRCUIT

(A926) FUSED B+ CIRCUIT

A/C CLUTCH RELAY

(C13) A/C CLUTCH RELAY CONTROL CIRCUIT OPEN

(C13) A/C CLUTCH RELAY CONTROL CIRCUIT SHORTED TO GROUND

PCM

TEST

ACTION

APPLICABILITY

1

Ignition on, engine not running.
With the DRBIII

t, actuate the A/C Clutch Relay.

Is the A/C Clutch Relay operating?

All

Yes

→ Refer to the INTERMITTENT CONDITION Symptom (Diagnos-

tic Procedure).
Perform POWERTRAIN VERIFICATION TEST VER - 2.

No

→ Go To 2

2

Turn the ignition off.
Remove the A/C Clutch Relay from the PDC.
Ignition on, engine not running.
Using a 12-volt test light connected to ground, probe the (F960) Fused Ignition
Switch Output circuit.
Does the test light illuminate brightly?

All

Yes

→ Go To 3

No

→ Repair the open or short to ground in the (F960) Fused Ignition

Switch Output circuit. Inspect and replace any open fuses.
Perform POWERTRAIN VERIFICATION TEST VER - 2.

237

DRIVEABILITY - NGC

TEST

ACTION

APPLICABILITY

3

Turn the ignition off.
Using a 12-volt test light connected to ground, probe the (A926) Fused B+ circuit of
the fuel pump relay in the PDC.
Does the test light illuminate brightly?

All

Yes

→ Go To 4

No

→ Repair the open or short to ground in the (A926) Fused B+ circuit.

Inspect and replace any open fuses.
Perform POWERTRAIN VERIFICATION TEST VER - 2.

4

Turn the ignition off.
Measure the resistance of the A/C Clutch Relay Coil.
Is the resistance between 60 to 80 ohms?

All

Yes

→ Go To 5

No

→ Replace the A/C Clutch Relay.

Perform POWERTRAIN VERIFICATION TEST VER - 2.

5

Disconnect the C3 PCM harness connector.
CAUTION: DO NOT PROBE THE PCM HARNESS CONNECTORS. PROBING
THE PCM HARNESS CONNECTORS WILL DAMAGE THE PCM TERMI-
NALS RESULTING IN POOR TERMINAL TO PIN CONNECTION. INSTALL
MILLER SPECIAL TOOL #8815 TO PERFORM DIAGNOSIS.
Measure the resistance of the (C13) A/C Clutch Relay Control circuit from the PDC
to the appropriate terminal of special tool #8815.
Is the resistance below 5.0 ohms?

All

Yes

→ Go To 6

No

→ Repair the open in the (C13) A/C Clutch Relay Control circuit.

Perform POWERTRAIN VERIFICATION TEST VER - 2.

6

Measure the resistance between ground and the (C13) A/C Clutch Relay Control
circuit in the PDC.
Is the resistance below 5.0 ohms?

All

Yes

→ Repair the short to ground in the (C13) A/C Clutch Relay Control

circuit.
Perform POWERTRAIN VERIFICATION TEST VER - 2.

No

→ Go To 7

7

NOTE: Before continuing, check the PCM harness connector terminals for
corrosion, damage, or terminal push out. Repair as necessary.
Using the schematics as a guide, inspect the wire harness and connectors. Pay
particular attention to all Power and Ground circuits.
If there are no possible causes remaining, view repair.

All

Repair

Replace and program the Powertrain Control Module per Service
Information.
Perform POWERTRAIN VERIFICATION TEST VER - 2.

238

DRIVEABILITY - NGC

P0645-A/C CLUTCH RELAY CIRCUIT —

Continued

Symptom:

P0685-ASD RELAY CONTROL CIRCUIT

When Monitored and Set Condition:

P0685-ASD RELAY CONTROL CIRCUIT

When Monitored:

With ignition on. Battery voltage above 10 volts.

Set Condition:

An open or shorted condition is detected in the ASD relay control circuit

for more than 2.7 seconds. ASD Relay state does not equal the desired state. P0688 will set
along with P0685.

POSSIBLE CAUSES

ASD RELAY OPERATION

(A209) FUSED B+ CIRCUITS

ASD RELAY

(K342) ASD RELAY CONTROL CIRCUIT OPEN

(K342) ASD RELAY CONTROL CIRCUIT SHORTED TO GROUND

PCM

TEST

ACTION

APPLICABILITY

1

Ignition on, engine not running.
With the DRBIII

t, actuate the ASD Relay.

Is the ASD Relay operating?

All

Yes

→ Refer to the INTERMITTENT CONDITION Symptom (Diagnos-

tic Procedure).
Perform POWERTRAIN VERIFICATION TEST VER - 5.

No

→ Go To 2

2

Turn the ignition off.
Remove the ASD Relay from the PDC.
Using a 12-volt test light connect to ground, probe the (A209) Fused B+ circuits in the
PDC.
Does the test light illuminate brightly?

All

Yes

→ Go To 3

No

→ Repair the open or short to ground in the (A209) Fused B+

circuits. Inspect and replace any open fuses.
Perform POWERTRAIN VERIFICATION TEST VER - 5.

3

Measure the resistance of the ASD Relay Coil.
Is the resistance between 60 to 80 ohms?

All

Yes

→ Go To 4

No

→ Replace the ASD Relay.

Perform POWERTRAIN VERIFICATION TEST VER - 5.

239

DRIVEABILITY - NGC

TEST

ACTION

APPLICABILITY

4

Disconnect the C3 PCM harness connector.
CAUTION: DO NOT PROBE THE PCM HARNESS CONNECTORS. PROBING
THE PCM HARNESS CONNECTORS WILL DAMAGE THE PCM TERMI-
NALS RESULTING IN POOR TERMINAL TO PIN CONNECTION. INSTALL
MILLER SPECIAL TOOL #8815 TO PERFORM DIAGNOSIS.
Measure the resistance of the (K342) ASD Relay Control circuit from the PDC to the
appropriate terminal of special tool #8815.
Is the resistance below 5.0 ohms?

All

Yes

→ Go To 5

No

→ Repair the open in the (K342) ASD Relay Control circuit.

Perform POWERTRAIN VERIFICATION TEST VER - 5.

5

Measure the resistance between ground and the (K342) ASD Relay Control circuit in
the PDC.
Is the resistance below 5.0 ohms?

All

Yes

→ Repair the short to ground in the (K342) ASD Relay Control

circuit.
Perform POWERTRAIN VERIFICATION TEST VER - 5.

No

→ Go To 6

6

NOTE: Before continuing, check the PCM harness connector terminals for
corrosion, damage, or terminal push out. Repair as necessary.
Using the schematics as a guide, inspect the wire harness and connectors. Pay
particular attention to all Power and Ground circuits.
If there are no possible causes remaining, view repair.

All

Repair

Replace and program the Powertrain Control Module per Service
Information.
Perform POWERTRAIN VERIFICATION TEST VER - 5.

240

DRIVEABILITY - NGC

P0685-ASD RELAY CONTROL CIRCUIT —

Continued

 

 

 

 

 

 

 

Content   ..  126  127  128  129   ..