Jeep Wrangler TJ. Manual - part 12

 

  Index      Jeep     Jeep Wrangler TJ - service repair manual 2005 year

 

Search            

 

 

 

 

 

 

 

 

 

Content   ..  10  11  12  13   ..

 

 

Jeep Wrangler TJ. Manual - part 12

 

 

Symptom:

NO PCI TRANSMISSION

When Monitored and Set Condition:

NO PCI TRANSMISSION

When Monitored:

With the ignition on and the module transmitting information on the

BUS.

Set Condition:

The code will set immediately if the onboard diagnostic cannot detect the

module transmitting information on the BUS. NOTE: Any Bus Failure will may cause a
stored code to set.

POSSIBLE CAUSES

AIRBAG CONTROL MODULE - ACM

STORED CODE OR INTERMITTENT CONDITION

ACTIVE CODE PRESENT

TEST

ACTION

APPLICABILITY

1

Turn the ignition on.
NOTE: Ensure the battery is fully charged.
NOTE: For the purpose of this test, the AECM and ORC modules will be
referred to as an ACM.
From the list below, select the appropriate module and DTC type for the this
diagnostic trouble code.
DETERMINE ACTIVE OR STORED DTC

All

ACM - ACTIVE

Go To

2

ACM - STORED

Go To

3

NOTE: When reconnecting airbag system components the Ignition must be
turned off and the Battery must be disconnected.

2

WARNING: TO AVOID PERSONAL INJURY OR DEATH, DISCONNECT THE
BATTERY AND WAIT TWO MINUTES BEFORE PROCEEDING.
WARNING: IF THE AIRBAG CONTROL MODULE IS DROPPED AT ANY
TIME, IT MUST BE REPLACED. FAILURE TO TAKE THE PROPER PRE-
CAUTIONS COULD RESULT IN ACCIDENTAL AIRBAG DEPLOYMENT
AND PERSONAL INJURY OR DEATH.
If there are no possible causes remaining, view repair.

All

Repair

Replace the Airbag Control Module in accordance with Service
Instructions.
Perform __AIRBAG VERIFICATION TEST - VER 1.

45

AIRBAG

TEST

ACTION

APPLICABILITY

3

With the DRBIII

t, record and erase all DTC’s from all Airbag modules.

If equipped with Passenger Airbag On - Off switch, read the DTC’s in all switch
positions.
If any ACTIVE codes are present they must be resolved before diagnosing any stored
codes.
WARNING: TO AVOID PERSONAL INJURY OR DEATH, TURN THE IGNI-
TION OFF, DISCONNECT THE BATTERY AND WAIT TWO MINUTES BE-
FORE PROCEEDING.
Using the wiring diagram/schematic as a guide, inspect the wiring and connectors.
Look for chaffed, pierced, pinched, or partially broken wires and broken, bent, pushed
out, spread, corroded, or contaminated terminals.
The following additional checks may assist you in identifying a possible intermittent
problem.
Reconnect any disconnected components and harness connector.
WARNING: TO AVOID PERSONAL INJURY OR DEATH, TURN THE IGNI-
TION ON, THEN RECONNECT THE BATTERY.
With the DRBIII

t monitor active codes as you work through the following steps.

WARNING: TO AVOID PERSONAL INJURY OR DEATH, MAINTAIN A SAFE
DISTANCE FROM ALL AIRBAGS WHILE PERFORMING THE FOLLOWING
STEPS.
Wiggle the wiring harness and connectors of the related airbag circuit or component.
If codes are related to the Driver Airbag circuits, rotate the steering wheel from stop
to stop.
IF only stored codes return continue the test until the problem area has been isolated
In the previous steps you have attempted to recreate the conditions responsible for
setting active DTC in question.
Are any ACTIVE DTCs present?

All

Yes

→ Select appropriate symptom from Symptom List.

No

→ No problem found at this time. Erase all codes before returning

vehicle to customer.

46

AIRBAG

NO PCI TRANSMISSION —

Continued

Symptom:

PASSENGER AIRBAG ON - OFF SWITCH OPEN

When Monitored and Set Condition:

PASSENGER AIRBAG ON - OFF SWITCH OPEN

When Monitored:

With the ignition on, the PAB MUX Switch Sense circuit supplies a 3

to 10 ms pulse every 100 ms across the On or Off switch resistor to the MUX Switch Return
circuit.

Set Condition:

The code will set if the ACM senses an open or high resistance on the PAB

MUX Switch Sense circuit or PAB MUX Switch Return circuit.

POSSIBLE CAUSES

CHECKING EQUIPMENT

PAB ON - OFF SWITCH OPEN

SWITCH DISCONNECTED

PASSENGER AIRBAG MUX SWITCH CIRCUIT OPEN

ACM, PASSENGER ON - OFF SWITCH CIRCUIT OPEN

STORED CODE OR INTERMITTENT CONDITION

ACTIVE CODE PRESENT

TEST

ACTION

APPLICABILITY

1

Turn the ignition on.
NOTE: Ensure that the battery is fully charged.
NOTE: For the purpose of this test, the AECM and ORC modules will be
referred to as an ACM.
SELECT ACTIVE or STORED DTC:

All

ACM - ACTIVE DTC

Go To

2

ACM - STORED DTC

Go To

7

NOTE: When reconnecting Airbag system components, the ignition must be
turned off and the battery must be disconnected.

2

Is this vehicle equipped with a Passenger Airbag On - Off Switch?

All

Yes

→ Go To 3

No

→ With the DRBIIIt in MISCELLANEOUS, read the Configure for

Airbag ON - OFF Switch current status. Enter the number 1 and
press enter to re configure the ACM for NO AIRBAG ON/OFF
SWITCH.
Perform __AIRBAG VERIFICATION TEST - VER 1.

47

AIRBAG

TEST

ACTION

APPLICABILITY

3

Gain access to the Passenger Airbag On - Off Switch connector.
Is the Passenger Airbag On - Off Switch connected to the dash harness?

All

Yes

→ Go To 4

No

→ Connect the Passenger Airbag On - Off switch to the dash harness

connector.
Perform __AIRBAG VERIFICATION TEST - VER 1.

4

WARNING: TO AVOID PERSONAL INJURY OR DEATH, TURN THE IGNI-
TION OFF, DISCONNECT THE BATTERY AND WAIT TWO MINUTES BE-
FORE PROCEEDING.
Disconnect the Passenger Airbag On - Off Switch.
NOTE: Check connectors - Clean and repair as necessary.
Measure the PAB On - Off Switch resistance between terminals 1 and 2 in both
switch positions.
The switch resistance specifications are: ON position = 175.0 to 190.0 ohms and OFF
position = 820.0 to 870.0 ohms.
Is the resistance within range for both switch positions?

All

Yes

→ Go To 5

No

→ Replace the Passenger Airbag ON - OFF Switch in accordance

with the service information.
Perform __AIRBAG VERIFICATION TEST - VER 1.

5

Disconnect the Airbag Control Module connector(s).
NOTE: Check connectors - Clean and repair as necessary.
WARNING: IF THE AIRBAG CONTROL MODULE IS DROPPED AT ANY
TIME, IT MUST BE REPLACED.
Connect the appropriate Load Tool Adaptor to the Airbag Control Module connector.
Measure the resistance of the PAB MUX Switch Sense between the ACM Adaptor and
the PAB On - Off Switch connector.
Measure the resistance of the PAB MUX Switch Return circuit between the ACM
Adaptor and the PAB On - Off Switch connector.
Is the resistance below 5.0 ohms on both circuits?

All

Yes

→ Go To 6

No

→ Repair the open Passenger Airbag MUX Switch circuit(s).

Perform __AIRBAG VERIFICATION TEST - VER 1.

6

WARNING: TO AVOID PERSONAL INJURY OR DEATH, TURN THE IGNI-
TION OFF, DISCONNECT THE BATTERY AND WAIT TWO MINUTES BE-
FORE PROCEEDING.
WARNING: IF THE AIRBAG CONTROL MODULE IS DROPPED AT ANY
TIME, IT MUST BE REPLACED. FAILURE TO TAKE THE PROPER PRE-
CAUTIONS COULD RESULT IN ACCIDENTAL AIRBAG DEPLOYMENT
AND PERSONAL INJURY OR DEATH.
If there are no possible causes remaining, view repair.

All

Repair

WARNING: MAKE SURE THE BATTERY IS DISCONNECTED,
THEN WAIT TWO MINUTES BEFORE PROCEEDING. Replace
the Airbag Control Module in accordance with Service Instruc-
tions.
Perform __AIRBAG VERIFICATION TEST - VER 1.

48

AIRBAG

PASSENGER AIRBAG ON - OFF SWITCH OPEN —

Continued

 

 

 

 

 

 

 

Content   ..  10  11  12  13   ..