Jeep Wrangler TJ. Manual - part 9

 

  Index      Jeep     Jeep Wrangler TJ - service repair manual 2005 year

 

Search            

 

 

 

 

 

 

 

 

 

Content   ..  7  8  9  10   ..

 

 

Jeep Wrangler TJ. Manual - part 9

 

 

Symptom:

LOSS OF IGNITION RUN - START

When Monitored and Set Condition:

LOSS OF IGNITION RUN - START

When Monitored:

With the ignition in the Run-Start position the ACM monitors the

Fused Ignition Switch Output Run-Start circuit for proper system voltage.

Set Condition:

If the voltage on the Fused Ignition Switch Output Run-Start circuit drops

below approximately 4.5 volts, the code will set.

POSSIBLE CAUSES

FUSED IGNITION SW OUTPUT RUN-START SHORT TO GROUND

IGNITION SWITCH RUN - START CIRCUIT OPEN

FUSED IGNITION SWITCH OUTPUT RUN-START CIRCUIT OPEN

ACM, FUSED IGNITION OUTPUT RUN-START CIRCUIT OPEN

ACM, RUN - START SHORTED TO GROUND

ON - OFF SWITCH, RUN - START CIRCUIT SHORTED TO GROUND

FUSED IGNITION SWITCH OUTPUT RUN - START CIRCUIT SHORT TO GROUND

STORED CODE OR INTERMITTENT CONDITION

ACTIVE CODE PRESENT

TEST

ACTION

APPLICABILITY

1

Ensure the battery is fully charged.
Turn the ignition on.
NOTE: For the purpose of this test, the AECM and ORC modules will be
referred to as an ACM.
DETERMINE ACTIVE OR STORED DTC:

All

ACM - ACTIVE DTC

Go To

2

ACM - STORED DTC

Go To

10

NOTE: When reconnecting Airbag system components, the ignition must be
turned off and the battery must be disconnected.

2

Turn Ignition off.
Remove and inspect the Airbag Run-Start Fuse.
NOTE: Check connectors - Clean and repair as necessary.
Is the Fuse open?

All

Yes

→ Go To 3

No

→ Go To 7

33

AIRBAG

TEST

ACTION

APPLICABILITY

3

Measure the resistance of the Fused Ignition Switch Output Run-Start circuit
between the Airbag Run - Start Fuse and ground.
Is the resistance below 10.0 ohms?

All

Yes

→ Go To 4

No

→ Replace Airbag Run - Start Fuse.

Perform __AIRBAG VERIFICATION TEST - VER 1.

4

Is this vehicle equipped with a Passenger Airbag On - Off Indicator?

All

Yes

→ Go To 5

No

→ Go To 6

5

Disconnect the Passenger Airbag On - Off Indicator connector
NOTE: Check connectors - Clean and repair as necessary.
Measure the resistance of the Fused Ignition Switch Output Run-Start Circuit
between the On - Off Indicator connector and ground.
Is the resistance below 10K ohms?

All

Yes

→ Go To 6

No

→ Replace the Passenger Airbag On - Off Switch and Airbag Run -

Start Fuse.
Perform __AIRBAG VERIFICATION TEST - VER 1.

6

WARNING: TO AVOID PERSONAL INJURY OR DEATH, TURN THE IGNI-
TION OFF, DISCONNECT THE BATTERY AND WAIT TWO MINUTES BE-
FORE PROCEEDING.
WARNING: IF THE AIRBAG CONTROL MODULE IS DROPPED AT ANY
TIME, IT MUST BE REPLACED. FAILURE TO TAKE THE PROPER PRE-
CAUTIONS COULD RESULT IN ACCIDENTAL AIRBAG DEPLOYMENT
AND PERSONAL INJURY OR DEATH.
Disconnect the Airbag Control Module connector
NOTE: Check connectors - Clean and repair as necessary.
Connect the appropriate Load Tool ACM Adaptor to the ACM connector(s).
Measure the resistance of the Fused Ignition Switch Output Run-Start circuit
between the ACM Adapter and ground.
Is the resistance below 10K ohms?

All

Yes

→ Repair the Fused Ignition Switch Output Run - Start circuit short

to ground.
Perform __AIRBAG VERIFICATION TEST - VER 1.

No

→ Replace the Airbag Control Module in accordance with Service

Instructions and replace the fuse.
Perform __AIRBAG VERIFICATION TEST - VER 1.

7

Turn the ignition on.
Measure the voltage of the Ignition Switch Output circuit at the Airbag Run - Start
fuse.
Is the voltage above approximately 6.0 volts?

All

Yes

→ Go To 8

No

→ Repair the open Ignition Switch Output Run - Start circuit.

Perform __AIRBAG VERIFICATION TEST - VER 1.

NOTE: Reinstall the fuse after performing this test.

34

AIRBAG

LOSS OF IGNITION RUN - START —

Continued

TEST

ACTION

APPLICABILITY

8

WARNING: TO AVOID PERSONAL INJURY OR DEATH, TURN THE IGNI-
TION OFF, DISCONNECT THE BATTERY AND WAIT TWO MINUTES BE-
FORE PROCEEDING.
WARNING: IF THE AIRBAG CONTROL MODULE IS DROPPED AT ANY
TIME, IT MUST BE REPLACED. FAILURE TO TAKE THE PROPER PRE-
CAUTIONS COULD RESULT IN ACCIDENTAL AIRBAG DEPLOYMENT
AND PERSONAL INJURY OR DEATH.
Disconnect the Airbag Control Module connector.
NOTE: Check connectors - Clean and repair as necessary.
Reinstall the previously removed Airbag Run-Start Fuse.
WARNING: TO AVOID PERSONAL INJURY OR DEATH, TURN THE IGNI-
TION ON, THEN RECONNECT THE BATTERY.
Measure the voltage of the Fused Ignition Switch Output Run-Start Circuit between
the Airbag Control Module connector ground.
Is the voltage above approximately 4.5 volts?

All

Yes

→ Go To 9

No

→ Repair open Fused Ignition Switch Output Run-Start circuit.

Perform __AIRBAG VERIFICATION TEST - VER 1.

9

WARNING: TO AVOID PERSONAL INJURY OR DEATH, TURN THE IGNI-
TION OFF, DISCONNECT THE BATTERY AND WAIT TWO MINUTES BE-
FORE PROCEEDING.
WARNING: IF THE AIRBAG CONTROL MODULE IS DROPPED AT ANY
TIME, IT MUST BE REPLACED. FAILURE TO TAKE THE PROPER PRE-
CAUTIONS COULD RESULT IN ACCIDENTAL AIRBAG DEPLOYMENT
AND PERSONAL INJURY OR DEATH.
If there are no possible causes remaining, view repair.

All

Repair

Replace the Airbag Control Module in accordance with Service
Instructions.
Perform __AIRBAG VERIFICATION TEST - VER 1.

35

AIRBAG

LOSS OF IGNITION RUN - START —

Continued

TEST

ACTION

APPLICABILITY

10

With the DRBIII

t, record and erase all DTC’s from all Airbag modules.

If equipped with Passenger Airbag On - Off switch, read the DTC’s in all switch
positions.
If any ACTIVE codes are present they must be resolved before diagnosing any stored
codes.
WARNING: TO AVOID PERSONAL INJURY OR DEATH, TURN THE IGNI-
TION OFF, DISCONNECT THE BATTERY AND WAIT TWO MINUTES BE-
FORE PROCEEDING.
Using the wiring diagram/schematic as a guide, inspect the wiring and connectors.
Look for chaffed, pierced, pinched, or partially broken wires and broken, bent, pushed
out, spread, corroded, or contaminated terminals.
The following additional checks may assist you in identifying a possible intermittent
problem.
Reconnect any disconnected components and harness connector.
WARNING: TO AVOID PERSONAL INJURY OR DEATH, TURN THE IGNI-
TION ON, THEN RECONNECT THE BATTERY.
With the DRBIII

t monitor active codes as you work through the following steps.

WARNING: TO AVOID PERSONAL INJURY OR DEATH, MAINTAIN A SAFE
DISTANCE FROM ALL AIRBAGS WHILE PERFORMING THE FOLLOWING
STEPS.
Wiggle the wiring harness and connectors of the related airbag circuit or component.
If codes are related to the Driver Airbag circuits, rotate the steering wheel from stop
to stop.
IF only stored codes return continue the test until the problem area has been isolated
In the previous steps you have attempted to recreate the conditions responsible for
setting active DTC in question.
Are any ACTIVE DTCs present?

All

Yes

→ Select appropriate symptom from Symptom List.

No

→ No problem found at this time. Erase all codes before returning

vehicle to customer.

36

AIRBAG

LOSS OF IGNITION RUN - START —

Continued

 

 

 

 

 

 

 

Content   ..  7  8  9  10   ..