Jeep Wrangler TJ. Manual - part 7

TEST

ACTION

APPLICABILITY

WARNING: TO AVOID PERSONAL INJURY OR DEATH, TURN THE IGNI-
TION OFF, DISCONNECT THE BATTERY AND WAIT TWO MINUTES BE-
FORE PROCEEDING.
Disconnect the Driver Airbag connector(s).
NOTE: Check connectors - Clean and repair as necessary.
WARNING: DO NOT PLACE AN INTACT UNDEPLOYED AIRBAG FACE
DOWN ON A HARD SURFACE, THE AIRBAG WILL PROPEL INTO THE AIR
IF ACCIDENTALLY DEPLOYED. FAILURE TO TAKE THE PROPER PRE-
CAUTIONS COULD RESULT IN ACCIDENTAL AIRBAG DEPLOYMENT
AND PERSONAL INJURY OR DEATH.
Connect the appropriate Load Tool to the Driver Airbag connector(s).
WARNING: TO AVOID PERSONAL INJURY OR DEATH, TURN THE IGNI-
TION ON, THEN RECONNECT THE BATTERY.
With the DRBIII

t, read the active Airbag Control Module DTC’s.

Does the DRBIII

t show DRIVER SQUIB 1 CIRCUIT SHORT?

All

Yes

→ Go To 3

→ Replace the Driver Airbag in accordance with the Service Infor-

mation.
Perform __AIRBAG VERIFICATION TEST - VER 1.

WARNING: TO AVOID PERSONAL INJURY OR DEATH, TURN THE IGNI-
TION OFF, DISCONNECT THE BATTERY AND WAIT TWO MINUTES BE-
FORE PROCEEDING.
Disconnect the Load Tool from the Driver Airbag connector(s).
Disconnect the Clockspring connector(s).
NOTE: Check connectors - Clean and repair as necessary.
Connect the appropriate Load Tool to the Clockspring connector(s).
WARNING: TO AVOID PERSONAL INJURY OR DEATH, TURN THE IGNI-
TION ON, THEN RECONNECT THE BATTERY.
With the DRBIII

t, read the active Airbag Control Module DTC’s.

Does the DRBIII

t show DRIVER SQUIB 1 CIRCUIT SHORT?

All

Yes

→ Go To 4

→ Replace the Clockspring in accordance with the Service Informa-

tion.
Perform __AIRBAG VERIFICATION TEST - VER 1.

WARNING: TO AVOID PERSONAL INJURY OR DEATH, TURN THE IGNI-
TION OFF, DISCONNECT THE BATTERY AND WAIT TWO MINUTES BE-
FORE PROCEEDING.
Disconnect the Load Tool from the Clockspring connector(s).
Disconnect the Airbag Control Module connector(s).
NOTE: Check connectors - Clean and repair as necessary.
Connect the appropriate Load Tool Adaptor to the Airbag Control Module connec-
tor(s).
Measure the resistance between the Driver Squib 1 Line 1 and Line 2 at the
Clockspring connector.
Is the resistance below 10K ohms?

All

Yes

→ Repair the Driver Squib 1 Line 1 circuit shorted to Driver Squib

1 Line 2 circuit.
Perform __AIRBAG VERIFICATION TEST - VER 1.

→ Go To 5

AIRBAG

DRIVER SQUIB 1 CIRCUIT SHORT —

Continued

TEST

ACTION

APPLICABILITY

WARNING: TO AVOID PERSONAL INJURY OR DEATH, TURN THE IGNI-
TION OFF, DISCONNECT THE BATTERY AND WAIT TWO MINUTES BE-
FORE PROCEEDING.
WARNING: IF THE AIRBAG CONTROL MODULE IS DROPPED AT ANY
TIME, IT MUST BE REPLACED. FAILURE TO TAKE THE PROPER PRE-
CAUTIONS COULD RESULT IN ACCIDENTAL AIRBAG DEPLOYMENT
AND PERSONAL INJURY OR DEATH.
If there are no possible causes remaining, view repair.

All

Repair:

Replace the Airbag Control Module in accordance with Service
Information.
Perform __AIRBAG VERIFICATION TEST - VER 1.

With the DRBIII

t, record and erase all DTC’s from all Airbag modules.

If equipped with Passenger Airbag On - Off switch, read the DTC’s in all switch
positions.
If any ACTIVE codes are present they must be resolved before diagnosing any stored
codes.
WARNING: TO AVOID PERSONAL INJURY OR DEATH, TURN THE IGNI-
TION OFF, DISCONNECT THE BATTERY AND WAIT TWO MINUTES BE-
FORE PROCEEDING.
Using the wiring diagram/schematic as a guide, inspect the wiring and connectors.
Look for chaffed, pierced, pinched, or partially broken wires and broken, bent, pushed
out, spread, corroded, or contaminated terminals.
The following additional checks may assist you in identifying a possible intermittent
problem.
Reconnect any disconnected components and harness connector.
WARNING: TO AVOID PERSONAL INJURY OR DEATH, TURN THE IGNI-
TION ON, THEN RECONNECT THE BATTERY.
With the DRBIII

t monitor active codes as you work through the following steps.

WARNING: TO AVOID PERSONAL INJURY OR DEATH, MAINTAIN A SAFE
DISTANCE FROM ALL AIRBAGS WHILE PERFORMING THE FOLLOWING
STEPS.
Wiggle the wiring harness and connectors of the related airbag circuit or component.
If codes are related to the Driver Airbag circuits, rotate the steering wheel from stop
to stop.
IF only stored codes return continue the test until the problem area has been isolated
In the previous steps you have attempted to recreate the conditions responsible for
setting active DTC in question.
Are any ACTIVE DTCs present?

All

Yes

→ Select appropriate symptom from Symptom List.

→ No problem found at this time. Erase all codes before returning

vehicle to customer.

AIRBAG

DRIVER SQUIB 1 CIRCUIT SHORT —

Continued

Symptom:

DRIVER SQUIB 1 SHORT TO BATTERY

When Monitored and Set Condition:

DRIVER SQUIB 1 SHORT TO BATTERY

When Monitored:

With the ignition on, the ACM monitors the voltage of the Driver Squib

1 circuits.

Set Condition:

The ACM has detected high voltage on the Driver Squib 1 circuits.

POSSIBLE CAUSES

DRIVER AIRBAG SQUIB 1 SHORT TO BATTERY

CLOCKSPRING, DRIVER SQUIB 1 SHORT TO BATTERY

DRIVER SQUIB 1 LINE 1 OR LINE 2 SHORT TO BATTERY

ACM, DRIVER SQUIB 1 SHORT TO BATTERY

STORED CODE OR INTERMITTENT CONDITION

ACTIVE CODE PRESENT

TEST

ACTION

APPLICABILITY

Turn the ignition on.
NOTE: Ensure the battery is fully charged.
NOTE: For the purpose of this test, the AECM and ORC modules will be
referred to as an ACM.
SELECT ACTIVE or STORED ACM DTC:

All

ACM - ACTIVE DTC

Go To

ACM - STORED DTC

Go To

NOTE: When reconnecting Airbag system components, the ignition must be
turned off and the battery must be disconnected.

AIRBAG

TEST

ACTION

APPLICABILITY

WARNING: TO AVOID PERSONAL INJURY OR DEATH, TURN THE IGNI-
TION OFF, DISCONNECT THE BATTERY AND WAIT TWO MINUTES BE-
FORE PROCEEDING.
Disconnect the Driver Airbag Squib connector(s).
WARNING: DO NOT PLACE AN INTACT UNDEPLOYED AIRBAG FACE
DOWN ON A HARD SURFACE, THE AIRBAG WILL PROPEL INTO THE AIR
IF ACCIDENTALLY DEPLOYED. FAILURE TO TAKE THE PROPER PRE-
CAUTIONS COULD RESULT IN ACCIDENTAL AIRBAG DEPLOYMENT
AND PERSONAL INJURY OR DEATH.
NOTE: Check connectors - Clean and repair as necessary.
Connect the appropriate Load Tool to the Driver Airbag connector(s).
WARNING: TO AVOID PERSONAL INJURY OR DEATH, TURN THE IGNI-
TION ON, THEN RECONNECT THE BATTERY.
With the DRBIII

t, read the active Airbag Control Module DTC’s.

Does the DRBIII

t show DRIVER SQUIB 1 SHORT TO BATTERY?

All

Yes

→ Go To 3

→ Replace the Driver Airbag in accordance with the Service Infor-

mation.
Perform __AIRBAG VERIFICATION TEST - VER 1.

t, read the active Airbag Control Module DTC’s.

Does the DRBIII

t show DRIVER SQUIB 1 SHORT TO BATTERY ?

All