Jeep Liberty KJ. Manual - part 270

 

  Index      Jeep     Jeep Liberty KJ - service repair manual 2006 year

 

Search            

 

 

 

 

 

 

 

 

 

Content   ..  268  269  270  271   ..

 

 

Jeep Liberty KJ. Manual - part 270

 

 

*LEFT REAR DOOR DOES NOT TRIP VTSS

For a complete wiring diagram Refer to Section 8W

Possible Causes

LEFT REAR DOOR AJAR CIRCUIT

BODY CONTROL MODULE (BCM)

Diagnostic Test

1.

CHECK LEFT REAR DOOR AJAR SWITCH FUNCTION

Verify that the lighting control on the multi-function switch is not in the Interior Lamps Defeat position.

Open the left rear door while observing the interior lamps.

Close the left rear door while observing the interior lamps.

Do the interior lamps function correctly with regard to the door position?

Yes

>> Go To 2

No

>> (Refer to 8 - ELECTRICAL/LAMPS/LIGHTING - INTERIOR - DIAGNOSIS AND TESTING) for Ajar

Switch related diagnostic procedures.

2.

CHECK DRIVER DOOR AJAR SWITCH STATUS WITH THE SCAN TOOL

NOTE: The VTSS must arm properly for the result of this test to be valid.
Turn the ignition on.

Open the driver door.

With the scan tool in BCM, select Data Display and read the Door Ajar Switch status for the left rear door.

Does the scan tool display: CLOSED?

Yes

>> Replace and program the BCM in accordance with the Service Information.

Perform BODY VERIFICATION TEST - VER 1. (Refer to 8 - ELECTRICAL/ELECTRONIC CONTROL
MODULES - STANDARD PROCEDURE).

No

>> (Refer to 8 - ELECTRICAL/LAMPS/LIGHTING - INTERIOR - DIAGNOSIS AND TESTING) for Ajar

Switch related diagnostic procedures.

8Q - 56

VEHICLE THEFT SECURITY - ELECTRICAL DIAGNOSTICS

KJ

*RIGHT REAR DOOR DOES NOT TRIP VTSS

For a complete wiring diagram Refer to Section 8W

Possible Causes

RIGHT REAR DOOR AJAR CIRCUIT MALFUNCTION

BODY CONTROL MODULE (BCM)

Diagnostic Test

1.

CHECK RIGHT REAR DOOR AJAR SWITCH FUNCTION

Verify that the lighting control on the multi-function switch is not in the Interior Lamps Defeat position.

Open the right rear door while observing the interior lamps.

Close the right rear door while observing the interior lamps.

Do the interior lamps function correctly with regard to the door position?

Yes

>> Go To 2

No

>> (Refer to 8 - ELECTRICAL/LAMPS/LIGHTING - INTERIOR - DIAGNOSIS AND TESTING) for Ajar

Switch related diagnostic procedures.

2.

CHECK RIGHT REAR DOOR AJAR SWITCH STATUS WITH THE SCAN TOOL

NOTE: The VTSS must arm properly for the result of this test to be valid.
Turn the ignition on.

Open the right rear door.

With the scan tool in BCM, select Data Display and read the Door Ajar Switch status for the right rear door.

Does the scan tool display: CLOSED?

Yes

>> Replace and program the BCM in accordance with the Service Information.

Perform BODY VERIFICATION TEST - VER 1. (Refer to 8 - ELECTRICAL/ELECTRONIC CONTROL
MODULES - STANDARD PROCEDURE).

No

>> (Refer to 8 - ELECTRICAL/LAMPS/LIGHTING - INTERIOR - DIAGNOSIS AND TESTING) for Ajar

Switch related diagnostic procedures.

*TAILGATE DOES NOT TRIP VTSS

For a complete wiring diagram Refer to Section 8W

Possible Causes

TAILGATE AJAR SWITCH CIRCUIT

BODY CONTROL MODULE (BCM)

Refer to (ELECTRICAL/LAMPS/LIGHTING - INTERIOR - DIAGNOSIS AND TESTING) for Ajar Switch related diag-
nostic procedures.

KJ

VEHICLE THEFT SECURITY - ELECTRICAL DIAGNOSTICS

8Q - 57

*VTSS WILL NOT ARM

For a complete wiring diagram Refer to Section 8W

Possible Causes

VEHICLE THEFT SECURITY SYSTEM (VTSS) DISABLED IN BODY CONTROL MODULE (BCM)

BODY CONTROL MODULE (BCM) DTCS PRESENT

AJAR SWITCH CIRCUITS

BODY CONTROL MODULE (BCM)

Diagnostic Test

1.

VERIFY THAT VTSS IS ENABLED IN THE BCM

Turn the ignition on.

With the scan tool in BCM, check that the VTSS is enabled.

Is the VTSS enabled?

Yes

>> Go To 2

No

>> With the scan tool, enable the VTSS.

Perform VTSS VERIFICATION TEST - 1A. (Refer to VTSS VERIFICATION TEST - 1A - STANDARD
PROCEDURE) in this Section.

2.

CHECK FOR DTCs IN THE BCM

With the scan tool, read BCM DTCs.

Does the scan tool display any DTCs?

Yes

>> Diagnose and repair the DTC(s) Refer to the Table of Contents in the applicable Section for the diag-

nostic procedure(s).

Perform VTSS VERIFICATION TEST - 1A. (Refer to VTSS VERIFICATION TEST - 1A - STANDARD
PROCEDURE) in this Section.

No

>> Go To 3

3.

CHECK AJAR SWITCH STATES WITH THE SCAN TOOL

Verify that the tailgate, flip-up glass, and all doors are closed.

With the scan tool in BCM, select Data Display and read the Ajar Switch states.

Do any Ajar Switch states display: Closed?

Yes

>> Diagnose and repair all Ajar Switch circuits that display as Closed on the scan tool. (Refer to 8 - ELEC-

TRICAL/LAMPS/LIGHTING - INTERIOR - DIAGNOSIS AND TESTING) for Ajar Switch related diagnos-
tic procedures.

Perform VTSS VERIFICATION TEST - 1A. (Refer to VTSS VERIFICATION TEST - 1A - STANDARD
PROCEDURE) in this Section.

No

>> Replace and program the BCM in accordance with the Service Information.

Perform BODY VERIFICATION TEST - VER 1. (Refer to 8 - ELECTRICAL/ELECTRONIC CONTROL
MODULES - STANDARD PROCEDURE).

8Q - 58

VEHICLE THEFT SECURITY - ELECTRICAL DIAGNOSTICS

KJ

INTERMITTENT CONDITION

POSSIBLE CAUSES

INTERMITTENT CONDITION

Diagnostic Test

1.

INTERMITTENT CONDITION

NOTE: The conditions that set the DTC are not present at this time. The following list may help in identi-
fying the intermittent condition.

WARNING: When the engine is operating, do not stand in direct line with the fan. Do not put your hands
near the pulleys, belts, or fan. Do not wear loose clothing. Failure to follow these instructions can result in
personal injury or death.
Refer to any Technical Service Bulletins (TSBs) that may apply.

Review the scan tool Freeze Frame information. If possible, try to duplicate the conditions under which the DTC set.

With the engine running at normal operating temperature, monitor the scan tool parameters related to the DTC while
wiggling the wire harness. Look for parameter values to change and/or a DTC to set.

Turn the ignition off.

Visually inspect the related wire harness. Disconnect all the related harness connectors. Look for any chafed,
pierced, pinched, partially broken wires and broken, bent, pushed out, or corroded terminals.

Perform a voltage drop test on the related circuits between the suspected inoperative component and the PCM.

CAUTION: Do not probe the PCM harness connectors. Probing the PCM harness connectors will damage
the PCM terminals resulting in poor terminal to pin connection. Install Miller Special Tool #8815 to perform
diagnosis.
Inspect and clean all PCM, engine, and chassis grounds that are related to the most current DTC.

If numerous trouble codes were set, use a wire schematic and look for any common ground or supply circuits.

For any Relay DTCs, actuate the Relay with the scan tool and wiggle the related wire harness to try to interrupt the
actuation.

For intermittent Evaporative Emission trouble codes perform a visual and physical inspection of the related parts
including hoses and the Fuel Filler cap.

For intermittent Misfire DTCs check for restrictions in the Intake and Exhaust system, proper installation of Sensors,
vacuum leaks, and binding components that are run by the accessory drive belt.

Use the scan tool to perform a System Test if one applies to failing component.

A co-pilot, data recorder, and/or lab scope should be used to help diagnose intermittent conditions.

Were any problems found during the above inspections?

Yes

>> Perform the necessary repairs.

Perform the POWERTRAIN VERIFICATION TEST. (Refer to 9 - ENGINE - STANDARD PROCEDURE)

No

>> Test Complete.

KJ

VEHICLE THEFT SECURITY - ELECTRICAL DIAGNOSTICS

8Q - 59

 

 

 

 

 

 

 

Content   ..  268  269  270  271   ..