Jeep Liberty KJ. Manual - part 262

 

  Index      Jeep     Jeep Liberty KJ - service repair manual 2006 year

 

Search            

 

 

 

 

 

 

 

 

 

Content   ..  260  261  262  263   ..

 

 

Jeep Liberty KJ. Manual - part 262

 

 

SKREEM/SKIM–EEPROM FAILURE

For a complete wiring diagram Refer to Section 8W.

When Monitored:
With the ignition on.

Set Condition:
When the value written to EEPROM memory does not equal the value read back after the write operation.

Possible Causes

SKREEM/SKIM INTERNAL DTC FAILURE

Diagnostic Test

1.

VERIFY THAT THE DTC IS ACTIVE

NOTE: This trouble code indicates an internal module fault.
Turn the ignition on.

With the scan tool, record and erase the SKREEM/SKIM DTCs.

Perform 5 ignition key cycles, leaving the ignition key on for a minimum of 90 seconds per cycle.

With the scan tool, read the SKREEM/SKIM DTCs.

Did this DTC reset?

Yes

>> Replace and program the SKREEM/SKIM in accordance with the Service Information.

Perform SKIS VERIFICATION TEST. (Refer to 8 - ELECTRICAL/VEHICLE THEFT SECURITY - STAN-
DARD PROCEDURE).

No

>> Test complete, the conditions that set this DTC are not present at this time.

8Q - 24

VEHICLE THEFT SECURITY - ELECTRICAL DIAGNOSTICS

KJ

SKREEM/SKIM–INTERNAL FAULT

For a complete wiring diagram Refer to Section 8W.

When Monitored:
With the ignition on.

Set Condition:
The SKREEM/SKIM has detected a fault during an internal self test.

Possible Causes

SKREEM/SKIM INTERNAL DTC FAILURE

Diagnostic Test

1.

VERIFY THAT THE DTC IS ACTIVE

NOTE: This trouble code indicates an internal module fault.
Turn the ignition on.

With the scan tool, record and erase the SKREEM/SKIM DTCs.

Perform 5 ignition key cycles, leaving the ignition key on for a minimum of 90 seconds per cycle.

With the scan tool, read the SKREEM/SKIM DTCs.

Did this DTC reset?

Yes

>> Replace and program the SKREEM/SKIM in accordance with the Service Information.

Perform SKIS VERIFICATION TEST. (Refer to 8 - ELECTRICAL/VEHICLE THEFT SECURITY - STAN-
DARD PROCEDURE).

No

>> Test complete, the conditions that set this DTC are not present at this time.

KJ

VEHICLE THEFT SECURITY - ELECTRICAL DIAGNOSTICS

8Q - 25

SKREEM/SKIM–PCM STATUS FAILURE

For a complete wiring diagram Refer to Section 8W.

When Monitored:
With the ignition on.

Set Condition:
If the SKREEM/SKIM fails to receive the PCM STATUS message from the PCM for at least 20.0 consecutive
seconds.

Possible Causes

WIRE HARNESS FAILURE

SKREEM/SKIM

PCM

Diagnostic Test

1.

VERIFY THAT THE DTC IS ACTIVE

NOTE: Verify that the PCM has good power and ground connections before continuing.
Turn the ignition on.

With the scan tool, record and erase the SKREEM/SKIM DTCs.

Turn the ignition off.

Wait 2 minutes.

Turn the ignition on.

With the scan tool, read the SKREEM/SKIM DTCs.

Did this DTC reset?

Yes

>> Go To 2

No

>> Perform the Intermittent Condition diagnostic procedure in this Section.

2.

INSPECT RELATED WIRING FOR CONDITION CAUSING THE FAULT

Turn the ignition off.

NOTE: Visually inspect the related wiring harness and PCI Bus circuits for any chafed, pierced, pinched,
and partially broken wires.

NOTE: Visually inspect the related wiring harness connectors for broken, bent, pushed out, and corroded
terminals.

NOTE: Refer to any Technical Service Bulletins (TSB) that may apply.

Were any problems found?

Yes

>> Repair as necessary.

Perform SKIS VERIFICATION TEST. (Refer to 8 - ELECTRICAL/VEHICLE THEFT SECURITY - STAN-
DARD PROCEDURE).

No

>> Go To 3

8Q - 26

VEHICLE THEFT SECURITY - ELECTRICAL DIAGNOSTICS

KJ

3.

VERIFY THAT THE DTC IS STILL ACTIVE

NOTE: Obtain the SKIM PIN before proceeding.
Turn the ignition on.

With the scan tool, erase all PCM and SKREEM/SKIM DTCs.

Perform 5 ignition key cycles, leaving the ignition key on for a minimum of 90 seconds per cycle.

With the scan tool, read the SKREEM/SKIM DTCs.

Did this DTC reset?

Yes

>> Replace and program the PCM in accordance with the Service Information.

Perform SKIS VERIFICATION TEST. (Refer to 8 - ELECTRICAL/VEHICLE THEFT SECURITY - STAN-
DARD PROCEDURE).

No

>> Test complete, the conditions that set this DTC are not present at this time.

KJ

VEHICLE THEFT SECURITY - ELECTRICAL DIAGNOSTICS

8Q - 27

 

 

 

 

 

 

 

Content   ..  260  261  262  263   ..