Jeep Liberty KJ. Manual - part 231

 

  Index      Jeep     Jeep Liberty KJ - service repair manual 2006 year

 

Search            

 

 

 

 

 

 

 

 

 

Content   ..  229  230  231  232   ..

 

 

Jeep Liberty KJ. Manual - part 231

 

 

19.

CHECK THE PASSENGER BLADDER PRESSURE SENSOR POWER CIRCUIT FOR A SHORT TO THE
OTHER SENSOR CIRCUITS

Measure the resistance between the Passenger Bladder Pressure Sensor Power circuit and the Passenger Bladder
Pressure Sensor Signal circuit.

Measure the resistance between the Passenger Bladder Pressure Sensor Power circuit and the Passenger Bladder
Pressure Sensor Ground circuit.

Measure the resistance between the Passenger Bladder Pressure Sensor Power circuit and the Seat Belt Tension
Sensor Power circuit.

Measure the resistance between the Passenger Bladder Pressure Sensor Power circuit and the Seat Belt Tension
Sensor Signal circuit.

Measure the resistance between the Passenger Bladder Pressure Sensor Power circuit and the Seat Belt Tension
Sensor Ground circuit.

Is the resistance below 10k ohms on any of the circuits?

Yes

>>

WARNING: If the Occupant Classification Module (OCM) is dropped at any time, it must be replaced. Failure
to take the proper precautions could result in accidental airbag deployment and personal injury or death.

WARNING: To avoid personal injury or death, turn the ignition off, disconnect the battery and wait two min-
utes before proceeding.

NOTE: The Occupant Classification Module (OCM) and the Passenger Seat Bladder and Cushion Kit are the
only serviceable OCS components.

Replace the OCS Bladder and Cushion Kit in accordance with the Service information.

Perform SYSTEM VERIFICATION REQUIRED test.

Perform *AIRBAG SYSTEM VERIFICATION TEST - VER 1.

No

>> Go To 20

20.

CHECK THE PASSENGER BLADDER PRESSURE SENSOR SIGNAL CIRCUIT FOR A SHORT TO THE
OTHER SENSOR CIRCUITS

Measure the resistance between the Passenger Bladder Pressure Sensor Signal circuit and the Passenger Bladder
Pressure Sensor Ground circuit.

Measure the resistance between the Passenger Bladder Pressure Sensor Signal circuit and the Seat Belt Tension
Sensor Power circuit.

Measure the resistance between the Passenger Bladder Pressure Sensor Signal circuit and the Seat Belt Tension
Sensor Signal circuit.

Measure the resistance between the Passenger Bladder Pressure Sensor Signal circuit and the Seat Belt Tension
Sensor Ground circuit.

Is the resistance below 10k ohms on any of the circuits?

Yes

>>

WARNING: If the Occupant Classification Module (OCM) is dropped at any time, it must be replaced. Failure
to take the proper precautions could result in accidental airbag deployment and personal injury or death.

WARNING: To avoid personal injury or death, turn the ignition off, disconnect the battery and wait two min-
utes before proceeding.

NOTE: The Occupant Classification Module (OCM) and the Passenger Seat Bladder and Cushion Kit are the
only serviceable OCS components.

Replace the OCS Bladder and Cushion Kit in accordance with the Service information.

Perform SYSTEM VERIFICATION REQUIRED test.

Perform *AIRBAG SYSTEM VERIFICATION TEST - VER 1.

No

>> Go To 21

8O - 230

RESTRAINTS - ELECTRICAL DIAGNOSTICS

KJ

21.

CHECK THE PASSENGER BLADDER PRESSURE SENSOR GROUND CIRCUIT FOR A SHORT TO THE
OTHER SENSOR CIRCUITS

Measure the resistance between the Passenger Bladder Pressure Sensor Ground circuit and the Seat Belt Tension
Sensor Power circuit.

Measure the resistance between the Passenger Bladder Pressure Sensor Ground circuit and the Seat Belt Tension
Sensor Signal circuit.

Measure the resistance between the Passenger Bladder Pressure Sensor Ground circuit and the Seat Belt Tension
Sensor Ground circuit.

Is the resistance below 10k ohms on any of the circuits?

Yes

>>

WARNING: If the Occupant Classification Module (OCM) is dropped at any time, it must be replaced. Failure
to take the proper precautions could result in accidental airbag deployment and personal injury or death.

WARNING: To avoid personal injury or death, turn the ignition off, disconnect the battery and wait two min-
utes before proceeding.

NOTE: The Occupant Classification Module (OCM) and the Passenger Seat Bladder and Cushion Kit are the
only serviceable OCS components.

Replace the OCS Bladder and Cushion Kit in accordance with the Service information.

Perform SYSTEM VERIFICATION REQUIRED test.

Perform *AIRBAG SYSTEM VERIFICATION TEST - VER 1.

No

>> Go To 22

22.

CHECK THE SEAT BELT TENSION SENSOR POWER CIRCUIT FOR A SHORT TO THE OTHER SENSOR
CIRCUITS

Measure the resistance between the Seat Belt Tension Sensor Power circuit and the Seat Belt Tension Sensor Sig-
nal circuit.

Measure the resistance between the Seat Belt Tension Sensor Power circuit and the Seat Belt Tension Sensor
Ground circuit.

Is the resistance below 10k ohms on any of the circuits?

Yes

>>

WARNING: If the Occupant Classification Module (OCM) is dropped at any time, it must be replaced. Failure
to take the proper precautions could result in accidental airbag deployment and personal injury or death.

WARNING: To avoid personal injury or death, turn the ignition off, disconnect the battery and wait two min-
utes before proceeding.

NOTE: The Occupant Classification Module (OCM) and the Passenger Seat Bladder and Cushion Kit are the
only serviceable OCS components.

Replace the OCS Bladder and Cushion Kit in accordance with the Service information.

Perform SYSTEM VERIFICATION REQUIRED test.

Perform *AIRBAG SYSTEM VERIFICATION TEST - VER 1.

No

>> Go To 23

KJ

RESTRAINTS - ELECTRICAL DIAGNOSTICS

8O - 231

23.

CHECK THE SEAT BELT TENSION SENSOR SIGNAL CIRCUIT FOR A SHORT TO THE SEAT BELT
TENSION SENSOR GROUND CIRCUIT

Measure the resistance between the Seat Belt Tension Sensor Signal circuit and the Seat Belt Tension Sensor
Ground circuit.

Is the resistance below 10k ohms?

Yes

>>

WARNING: If the Occupant Classification Module (OCM) is dropped at any time, it must be replaced. Failure
to take the proper precautions could result in accidental airbag deployment and personal injury or death.

WARNING: To avoid personal injury or death, turn the ignition off, disconnect the battery and wait two min-
utes before proceeding.

NOTE: The Occupant Classification Module (OCM) and the Passenger Seat Bladder and Cushion Kit are the
only serviceable OCS components.

Replace the OCS Bladder and Cushion Kit in accordance with the Service information.

Perform SYSTEM VERIFICATION REQUIRED test.

Perform *AIRBAG SYSTEM VERIFICATION TEST - VER 1.

No

>> Go To 26

24.

CHECK FOR AN OPEN PASSENGER BLADDER PRESSURE SENSOR GROUND CIRCUIT

WARNING: To avoid personal injury or death, turn the ignition off, disconnect the battery and wait two min-
utes before proceeding.
Disconnect the OCM harness connector.

Measure the resistance of the Passenger Bladder Pressure Sensor Ground circuit between the Passenger Seat
Weight Sensor harness connector and the OCM harness connector.

Is the resistance below 5.0 ohms?

Yes

>> Go To 26

No

>>

WARNING: If the Occupant Classification Module (OCM) is dropped at any time, it must be replaced. Failure
to take the proper precautions could result in accidental airbag deployment and personal injury or death.

WARNING: To avoid personal injury or death, turn the ignition off, disconnect the battery and wait two min-
utes before proceeding.

NOTE: The Occupant Classification Module (OCM) and the Passenger Seat Bladder and Cushion Kit are the
only serviceable OCS components.

Replace the OCS Bladder and Cushion Kit in accordance with the Service information.

Perform SYSTEM VERIFICATION REQUIRED test.

Perform *AIRBAG SYSTEM VERIFICATION TEST - VER 1.

25.

CHECK FOR AN OPEN SEAT BELT TENSION SENSOR GROUND CIRCUIT

WARNING: To avoid personal injury or death, turn the ignition off, disconnect the battery and wait two min-
utes before proceeding.
Disconnect the OCM harness connector.

Measure the resistance of the Seat Belt Tension Sensor Ground circuit between the Belt Tension Sensor harness
connector and the OCM harness connector.

Is the resistance below 5.0 ohms?

Yes

>> Go To 26

No

>>

WARNING: If the Occupant Classification Module (OCM) is dropped at any time, it must be replaced. Failure
to take the proper precautions could result in accidental airbag deployment and personal injury or death.

8O - 232

RESTRAINTS - ELECTRICAL DIAGNOSTICS

KJ

NOTE: The Occupant Classification Module (OCM) and the Passenger Seat Bladder and Cushion Kit are the
only serviceable OCS components.

Replace the OCS Bladder and Cushion Kit in accordance with the Service information.

Perform SYSTEM VERIFICATION REQUIRED test.

Perform *AIRBAG SYSTEM VERIFICATION TEST - VER 1.

26.

DETERMINE THE CORRECT REPAIR

NOTE: The Occupant Classification Module (OCM) and the Passenger Seat Bladder and Cushion Kit are the
only serviceable OCS components.
Determine the correct repair by verifying if the front passenger seat has a Bladder and Cushion Service Kit as
follows:

If possible, check the vehicle’s repair history.

The Service Kit wiring harness uses tamper resistant material on the harness connector. Inspect for the tamper
resistant material on the harness connector.

Does the seat have a Bladder and Cushion Service Kit?

Yes

>>

WARNING: If the Occupant Classification Module (OCM) is dropped at any time, it must be replaced. Failure
to take the proper precautions could result in accidental airbag deployment and personal injury or death.

WARNING: To avoid personal injury or death, turn the ignition off, disconnect the battery and wait two min-
utes before proceeding.

NOTE: The Bladder and Cushion Kit are calibrated as an assembly. Do not disconnect the Bladder from the
Cushion Kit. Service only as an assembly.

Replace OCS Bladder and Cushion Kit in accordance with the Service information.

Perform SYSTEM VERIFICATION REQUIRED test.

Perform AIRBAG SYSTEM VERIFICATION TEST - VER 1.

No

>>

WARNING: If the Occupant Classification Module (OCM) is dropped at any time, it must be replaced. Failure
to take the proper precautions could result in accidental airbag deployment and personal injury or death.

WARNING: To avoid personal injury or death, turn the ignition off, disconnect the battery and wait two min-
utes before proceeding.

NOTE: The Bladder and Cushion Kit are calibrated as an assembly. Do not disconnect the Bladder from the
Cushion Kit. Service only as an assembly.

Replace the OCM in accordance with the Service Information.

Perform SYSTEM VERIFICATION REQUIRED test.

Perform *AIRBAG SYSTEM VERIFICATION TEST - VER 1.

KJ

RESTRAINTS - ELECTRICAL DIAGNOSTICS

8O - 233

 

 

 

 

 

 

 

Content   ..  229  230  231  232   ..