Jeep Liberty KJ. Manual - part 230

 

  Index      Jeep     Jeep Liberty KJ - service repair manual 2006 year

 

Search            

 

 

 

 

 

 

 

 

 

Content   ..  228  229  230  231   ..

 

 

Jeep Liberty KJ. Manual - part 230

 

 

NOTE: The Occupant Classification Module (OCM) and the Passenger Seat Bladder and Cushion Kit are the
only serviceable OCS components.

Replace the OCS Bladder and Cushion Kit in accordance with the Service information.

Perform SYSTEM VERIFICATION REQUIRED test.

Perform *AIRBAG SYSTEM VERIFICATION TEST - VER 1.

9.

CHECK FOR AN OPEN PASSENGER SEAT WEIGHT SENSOR

WARNING: To avoid personal injury or death, turn the ignition off, disconnect the battery and wait two min-
utes before proceeding.
Disconnect the OCM harness connector.

Measure the resistance between the Passenger Bladder Pressure Sensor Power circuit and the Passenger Bladder
Pressure Sensor Ground circuit in the OCM harness connector.

NOTE: Verify that the DVOM is connected with the positive lead to the Power circuit and the negative lead
to the Ground circuit.

Is the resistance approximately 3.25k ohms?

Yes

>> Go To 10

No

>>

WARNING: If the Occupant Classification Module (OCM) is dropped at any time, it must be replaced. Failure
to take the proper precautions could result in accidental airbag deployment and personal injury or death.

NOTE: The Occupant Classification Module (OCM) and the Passenger Seat Bladder and Cushion Kit are the
only serviceable OCS components.

Replace the OCS Bladder and Cushion Kit in accordance with the Service information.

Perform SYSTEM VERIFICATION REQUIRED test.

Perform *AIRBAG SYSTEM VERIFICATION TEST - VER 1.

10.

CHECK FOR AN OPEN PASSENGER SEAT WEIGHT SENSOR

Measure the resistance between the Passenger Bladder Pressure Sensor Signal circuit and the Passenger Bladder
Pressure Sensor Ground circuit in the OCM harness connector.

NOTE: Verify that the DVOM is connected with the positive lead to the Signal circuit and the negative lead
to the Ground circuit.

Is the resistance approximately 106k ohms?

Yes

>> Go To 11

No

>>

WARNING: If the Occupant Classification Module (OCM) is dropped at any time, it must be replaced. Failure
to take the proper precautions could result in accidental airbag deployment and personal injury or death.

NOTE: The Occupant Classification Module (OCM) and the Passenger Seat Bladder and Cushion Kit are the
only serviceable OCS components.

Replace the OCS Bladder and Cushion Kit in accordance with the Service information.

Perform SYSTEM VERIFICATION REQUIRED test.

Perform *AIRBAG SYSTEM VERIFICATION TEST - VER 1.

8O - 226

RESTRAINTS - ELECTRICAL DIAGNOSTICS

KJ

11.

CHECK FOR AN OPEN SEAT BELT TENSION SENSOR

Connect the Belt Tension Sensor.

Measure the resistance between the Seat Belt Tension Sensor Power circuit and the Seat Belt Tension Sensor
Ground circuit in the OCM harness connector.

NOTE: Verify that the DVOM is connected with the positive lead to the Power circuit and the negative lead
to the Ground circuit.

Is the resistance approximately 7.5k ohms?

Yes

>> Go To 12

No

>> Replace the Front Passenger Seat Belt and Retractor Assembly and the Belt Tension Sensor in accor-

dance with the Service Information.

Perform SYSTEM VERIFICATION REQUIRED test.

Perform *AIRBAG SYSTEM VERIFICATION TEST - VER 1.

12.

CHECK FOR AN OPEN SEAT BELT TENSION SENSOR

Measure the resistance between the Seat Belt Tension Sensor Signal circuit and the Seat Belt Tension Sensor
Ground circuit in the OCM harness connector.

NOTE: Verify that the DVOM is connected with the positive lead to the Signal circuit and the negative lead
to the Ground circuit.

Is the resistance approximately 19.5m ohms?

Yes

>> Go To 26

No

>> Replace the Front Passenger Seat Belt and Retractor Assembly and the Belt Tension Sensor in accor-

dance with the Service Information.

Perform SYSTEM VERIFICATION REQUIRED test.

Perform *AIRBAG SYSTEM VERIFICATION TEST - VER 1.

13.

CHECK THE PASSENGER BLADDER PRESSURE SENSOR AND THE SEAT BELT TENSION SENSOR
POWER, SIGNAL, AND GROUND CIRCUIT FOR A SHORT TO VOLTAGE

WARNING: To avoid personal injury or death, turn the ignition off, disconnect the battery and wait two min-
utes before proceeding.
Disconnect the OCM harness connector.

WARNING: To avoid personal injury or death, turn the ignition on, then reconnect the battery.
Measure the voltage of the Passenger Bladder Pressure Sensor Power circuit.

Measure the voltage of the Passenger Bladder Pressure Sensor Signal circuit.

Measure the voltage of the Passenger Bladder Pressure Sensor Ground circuit.

Measure the voltage of the Seat Belt Tension Sensor Power circuit.

Measure the voltage of the Seat Belt Tension Sensor Signal circuit.

Measure the voltage of the Seat Belt Tension Sensor Ground circuit.

Is there any voltage present on any of the circuits?

Yes

>>

WARNING: If the Occupant Classification Module (OCM) is dropped at any time, it must be replaced. Failure
to take the proper precautions could result in accidental airbag deployment and personal injury or death.

WARNING: To avoid personal injury or death, turn the ignition off, disconnect the battery and wait two min-
utes before proceeding.

KJ

RESTRAINTS - ELECTRICAL DIAGNOSTICS

8O - 227

NOTE: The Occupant Classification Module (OCM) and the Passenger Seat Bladder and Cushion Kit are the
only serviceable OCS components.

Replace the OCS Bladder and Cushion Kit in accordance with the Service information.

Perform SYSTEM VERIFICATION REQUIRED test.

Perform *AIRBAG SYSTEM VERIFICATION TEST - VER 1.

No

>> Go To 14

14.

CHECK THE PASSENGER BLADDER PRESSURE SENSOR POWER CIRCUIT FOR AN OPEN

WARNING: To avoid personal injury or death, turn the ignition off, disconnect the battery and wait two min-
utes before proceeding.
Measure the resistance of the Passenger Bladder Pressure Sensor Power circuit between the OCM connector and
the Passenger Seat Weight Sensor connector.

Is the resistance below 5.0 ohms?

Yes

>> Go To 15

No

>>

WARNING: If the Occupant Classification Module (OCM) is dropped at any time, it must be replaced. Failure
to take the proper precautions could result in accidental airbag deployment and personal injury or death.

NOTE: The Occupant Classification Module (OCM) and the Passenger Seat Bladder and Cushion Kit are the
only serviceable OCS components.

Replace the OCS Bladder and Cushion Kit in accordance with the Service information.

Perform SYSTEM VERIFICATION REQUIRED test.

Perform *AIRBAG SYSTEM VERIFICATION TEST - VER 1.

15.

CHECK THE PASSENGER BLADDER PRESSURE SENSOR SIGNAL CIRCUIT FOR AN OPEN

Measure the resistance of the Passenger Bladder Pressure Sensor Signal circuit between the OCM connector and
the Passenger Seat Weight Sensor connector.

Is the resistance below 5.0 ohms?

Yes

>> Go To 16

No

>>

WARNING: If the Occupant Classification Module (OCM) is dropped at any time, it must be replaced. Failure
to take the proper precautions could result in accidental airbag deployment and personal injury or death.

WARNING: To avoid personal injury or death, turn the ignition off, disconnect the battery and wait two min-
utes before proceeding.

NOTE: The Occupant Classification Module (OCM) and the Passenger Seat Bladder and Cushion Kit are the
only serviceable OCS components.

Replace the OCS Bladder and Cushion Kit in accordance with the Service information.

Perform SYSTEM VERIFICATION REQUIRED test.

Perform *AIRBAG SYSTEM VERIFICATION TEST - VER 1.

16.

CHECK THE SEAT BELT TENSION SENSOR POWER CIRCUIT FOR AN OPEN

Measure the resistance of the Seat Belt Tension Sensor Power circuit between the OCM connector and the Belt
Tension Sensor connector.

Is the resistance below 5.0 ohms?

Yes

>> Go To 17

No

>>

WARNING: If the Occupant Classification Module (OCM) is dropped at any time, it must be replaced. Failure
to take the proper precautions could result in accidental airbag deployment and personal injury or death.

WARNING: To avoid personal injury or death, turn the ignition off, disconnect the battery and wait two min-
utes before proceeding.

8O - 228

RESTRAINTS - ELECTRICAL DIAGNOSTICS

KJ

NOTE: The Occupant Classification Module (OCM) and the Passenger Seat Bladder and Cushion Kit are the
only serviceable OCS components.

Replace the OCS Bladder and Cushion Kit in accordance with the Service information.

Perform SYSTEM VERIFICATION REQUIRED test.

Perform *AIRBAG SYSTEM VERIFICATION TEST - VER 1.

17.

CHECK THE SEAT BELT TENSION SENSOR SIGNAL CIRCUIT FOR AN OPEN

Measure the resistance of the Seat Belt Tension Sensor Signal circuit between the OCM connector and the Belt
Tension Sensor connector.

Is the resistance below 5.0 ohms?

Yes

>> Go To 18

No

>>

WARNING: If the Occupant Classification Module (OCM) is dropped at any time, it must be replaced. Failure
to take the proper precautions could result in accidental airbag deployment and personal injury or death.

WARNING: To avoid personal injury or death, turn the ignition off, disconnect the battery and wait two min-
utes before proceeding.

NOTE: The Occupant Classification Module (OCM) and the Passenger Seat Bladder and Cushion Kit are the
only serviceable OCS components.

Replace the OCS Bladder and Cushion Kit in accordance with the Service information.

Perform SYSTEM VERIFICATION REQUIRED test.

Perform *AIRBAG SYSTEM VERIFICATION TEST - VER 1.

18.

CHECK THE PASSENGER BLADDER PRESSURE SENSOR AND THE SEAT BELT TENSION SENSOR
POWER, SIGNAL, AND GROUND CIRCUIT FOR A SHORT TO GROUND

Measure the resistance between ground and the Passenger Bladder Pressure Sensor Power circuit.

Measure the resistance between ground and the Passenger Bladder Pressure Sensor Signal circuit.

Measure the resistance between ground and the Passenger Bladder Pressure Sensor Ground circuit.

Measure the resistance between ground and the Seat Belt Tension Sensor Power circuit.

Measure the resistance between ground and the Seat Belt Tension Sensor Signal circuit.

Measure the resistance between ground and the Seat Belt Tension Sensor Ground circuit.

Is the resistance below 10k ohms on any of the circuits?

Yes

>>

WARNING: If the Occupant Classification Module (OCM) is dropped at any time, it must be replaced. Failure
to take the proper precautions could result in accidental airbag deployment and personal injury or death.

WARNING: To avoid personal injury or death, turn the ignition off, disconnect the battery and wait two min-
utes before proceeding.

NOTE: The Occupant Classification Module (OCM) and the Passenger Seat Bladder and Cushion Kit are the
only serviceable OCS components.

Replace the OCS Bladder and Cushion Kit in accordance with the Service information.

Perform SYSTEM VERIFICATION REQUIRED test.

Perform *AIRBAG SYSTEM VERIFICATION TEST - VER 1.

No

>> Go To 19

KJ

RESTRAINTS - ELECTRICAL DIAGNOSTICS

8O - 229

 

 

 

 

 

 

 

Content   ..  228  229  230  231   ..