Jeep Liberty KJ. Manual - part 1111

 

  Index      Jeep     Jeep Liberty KJ - service repair manual 2006 year

 

Search            

 

 

 

 

 

 

 

 

 

Content   ..  1109  1110  1111  1112   ..

 

 

Jeep Liberty KJ. Manual - part 1111

 

 

With the scan tool, read ABS DTCs.

Does this DTC reset?

Yes

>> Replace the Anti-Lock Brakes Module in accordance with the Service Information.

Perform ABS VERIFICATION TEST - VER 1. (Refer to 5 - BRAKES - STANDARD PROCEDURE).

No

>> Perform ABS VERIFICATION TEST - VER 1. (Refer to 5 - BRAKES - STANDARD PROCEDURE).

5 - 204

BRAKES - ABS ELECTRICAL DIAGNOSTICS

KJ

C2206–VEHICLE CONFIGURATION MISMATCH

For a complete wiring diagram Refer to Section 8W

When Monitored:
Once per ignition cycle, but not during cranking.
Or, if low supply voltage faults are detected.

Set Condition:
If the Anti-Lock Brakes Module either fails to receive country code data from the Body Control Module (BCM)
or the configuration information it receives from the BCM is different than that received during the previous
ignition cycle.

Possible Causes

WIRING HARNESS, TERMINAL, CONNECTOR DAMAGE

DTCs RELATED TO BATTERY VOLTAGE, IGNITION, OR VIN MESSAGES

CAN C BUS CIRCUITS OPEN OR SHORTED

BCM DTCs PRESENT

BCM NOT PROGRAMMED OR PROGRAMMED WITH INCORRECT VEHICLE DATA

BCM

ANTI-LOCK BRAKES MODULE

Diagnostic Test

1.

VERIFY DTC IS ACTIVE

Turn the ignition on.

With the scan tool, read and record ABS DTCs.

With the scan tool, read and record Environmental Data (EV Data).

With the scan tool, erase ABS DTCs.

Cycle the ignition switch.

With the scan tool, read ABS DTCs.

Does this DTC reset?

Yes

>> Go To 2

No

>> Using the schematics as a guide, check the Anti-Lock Brakes Module and the BCM pins, terminals, and

connectors for corrosion, damage, and terminal push out. Pay particular attention to all Communication
circuits.

Perform ABS VERIFICATION TEST - VER 1. (Refer to 5 - BRAKES - STANDARD PROCEDURE).

2.

CHECK FOR ANY OF THE FOLLOWING ACTIVE DTCs

With the scan tool, read all active DTCs from all CAN C Bus modules.

NOTE: Check for CAN C hardware electrical, VIN Missing/Mismatch, battery or ignition related DTCs.

Does the scan tool display any active DTCs related to the conditions listed above?

Yes

>> Diagnose and repair the DTC(s). Refer to the Table of Contents in the applicable Section.

No

>> Go To 3

KJ

BRAKES - ABS ELECTRICAL DIAGNOSTICS

5 - 205

3.

CHECK IF BCM DTCs ARE PRESENT

With the scan tool, read BCM DTCs.

Are any DTCs present?

Yes

>> Diagnose and repair the DTC(s). Refer to the Table of Contents in the applicable Section.

Perform ABS VERIFICATION TEST - VER 1. (Refer to 5 - BRAKES - STANDARD PROCEDURE).

No

>> Go To 4

4.

VERIFY CORRECT BCM IS INSTALLED IN THE VEHICLE

With the scan tool, verify that the BCM part number is correct for the vehicle.

Is the correct BCM installed in the vehicle?

Yes

>> Replace and program the BCM in accordance with the Service Information.

Perform BODY VERIFICATION TEST – VER 1. (Refer to 8 - ELECTRICAL/ELECTRONIC CONTROL
MODULES - STANDARD PROCEDURE).

No

>> Go To 5

5.

VERIFY BCM IS PROGRAMMED WITH CORRECT VEHICLE DATA

With the scan tool, verify that the BCM is programmed with the correct vehicle data.

Is the BCM programmed with the correct vehicle data?

Yes

>> Program the BCM in accordance with the Service Information.

Perform BODY VERIFICATION TEST – VER 1. (Refer to 8 - ELECTRICAL/ELECTRONIC CONTROL
MODULES - STANDARD PROCEDURE).

No

>> Go To 6

6.

CHECK FOR ADDITIONAL COMMUNICATION RELATED DTCs

With the scan tool, select Network View and select Advanced.

Is there more than one module with active DTCs “Logged Against” the BCM?

Yes

>> Replace/update the BCM in accordance with the service information.

Perform BODY VERIFICATION TEST – VER 1. (Refer to 8 - ELECTRICAL/ELECTRONIC CONTROL
MODULES - STANDARD PROCEDURE).

Perform ABS VERIFICATION TEST - VER 1. (Refer to 5 - BRAKES - STANDARD PROCEDURE).

No

>> Using the schematics as a guide, check the Anti-Lock Brakes Module pins, terminals, and connectors

for corrosion, damage, and terminal push out. Pay particular attention to all Communication circuits. If
no problems are found, replace the Anti-Lock Brakes Module in accordance with the Service Informa-
tion.

Perform ABS VERIFICATION TEST - VER 1. (Refer to 5 - BRAKES - STANDARD PROCEDURE).

U0002–CAN C BUS OFF PERFORMANCE

For a complete wiring diagram Refer to Section 8W.

5 - 206

BRAKES - ABS ELECTRICAL DIAGNOSTICS

KJ

When Monitored:
With the ignition on.

Set Condition:
If the Anti-Lock Brakes Module detects a CAN Bus off event.

Perform CAN C Bus Communication Failure diagnostic test procedure. (Refer to 8 - ELECTRICAL/ELECTRONIC
CONTROL MODULES - DIAGNOSIS AND TESTING)
.

KJ

BRAKES - ABS ELECTRICAL DIAGNOSTICS

5 - 207

 

 

 

 

 

 

 

Content   ..  1109  1110  1111  1112   ..