Jeep Grand Cherokee WK. Manual - part 516

 

  Index      Jeep     Jeep Grand Cherokee WK - service repair manual 2005 year

 

Search            

 

 

 

 

 

 

 

 

 

Content   ..  514  515  516  517   ..

 

 

Jeep Grand Cherokee WK. Manual - part 516

 

 

B1D6D–SEAT HORIZONTAL POSITION SENSOR CIRCUIT LOW (CONTINUED)

3.

CHECK THE (G401) DRIVER SEAT HORIZONTAL POSITION SENSE WIRE FOR A SHORT TO GROUND

Disconnect the Memory Seat Module C3 connector.

NOTE: Check connectors – Clean and repair as necessary.
Measure the resistance of the (G401) Driver Seat Horizontal Position
Sense wire at the Driver Horizontal Seat Adjuster Motor connector to
ground.

Is the resistance below 1000.0 ohm?

Yes

>> Repair the (G401) Driver Seat Horizontal Position Sense

circuit for a short to ground.

Perform POWER SEAT SYSTEM VERIFICATION TEST –
VER 1 (Refer to 8 - ELECTRICAL/POWER SEATS -
DIAGNOSIS AND TESTING)

No

>> Replace the Memory Seat Module.

Perform POWER SEAT SYSTEM VERIFICATION TEST –
VER 1 (Refer to 8 - ELECTRICAL/POWER SEATS -
DIAGNOSIS AND TESTING)

8N - 224

POWER SEATS - ELECTRICAL DIAGNOSTICS

WK

B1D6E–SEAT HORIZONTAL POSITION SENSOR CIRCUIT HIGH

WK

POWER SEATS - ELECTRICAL DIAGNOSTICS

8N - 225

B1D6E–SEAT HORIZONTAL POSITION SENSOR CIRCUIT HIGH (CONTINUED)

For the Power Seat System circuit diagram (Refer to 8 - ELECTRICAL/POWER SEATS - SCHEMATICS AND DIA-
GRAMS)

For a complete wiring diagram Refer to Section 8W.

When Monitored:
When the seat motor is activated (sensor supply voltage is switched on whenever motor is activated).

Set Condition:
If during motor operation the sensor voltage is not within a specified range this code will set. This DTC will
only set when the seat switch is moved in the same direction three consecutive times.

Possible Causes

(G401) DRIVER SEAT HORZONTAL POSITION SENSE CIRCUIT SHORTED TO VOLTAGE

DRIVER RECLINER SEAT ADJUSTER MOTOR

MEMORY SEAT MODULE

Diagnostic Test

1.

TEST FOR INTERMITTENT CONDITION

Turn the ignition on.

With the scan tool, record and erase DTC’s

Move the seat switch in the horizontal position 3 times.

With the scan tool, read DTC’s.

Does the scan tool display B1D6E–SEAT HORIZONTAL POSITION SENSOR CIRCUIT HIGH?

Yes

>> Go To 2

No

>> The conditions that caused this code to set are not present at this time. Using the wiring diagram/sche-

matic as a guide, inspect the wiring and connectors.

Perform POWER SEAT SYSTEM VERIFICATION TEST - VER 1. (Refer to 8 - ELECTRICAL/POWER
SEATS - DIAGNOSIS AND TESTING)

2.

CHECK THE (G401) DRIVER SEAT HORIZONTAL POSITION SENSE VOLTAGE

Disconnect the Driver Horizontal Seat Adjuster Motor.

NOTE: Check connectors – Clean and repair as necessary.
With the scan tool erase DTC’s

Move the seat switch in the horizontal positions 3 times.

With the scan tool, read DTC’s.

Does the same DTC reset?

No

>> Inspect the position sense wire for a possible intermittent short to voltage from another circuit, if OK

replace the Driver Horizontal Seat Adjuster Motor assembly.

Perform POWER SEAT SYSTEM VERIFICATION TEST – VER 1 (Refer to 8 - ELECTRICAL/POWER
SEATS - DIAGNOSIS AND TESTING)

Yes

>> Inspect the position sense wire for a possible short to voltage from another circuit, if OK replace the

Memory Seat Module.

Perform POWER SEAT SYSTEM VERIFICATION TEST – VER 1 (Refer to 8 - ELECTRICAL/POWER
SEATS - DIAGNOSIS AND TESTING)

8N - 226

POWER SEATS - ELECTRICAL DIAGNOSTICS

WK

B1D71–SEAT FRONT VERTICAL POSITION SENSOR CIRCUIT LOW

WK

POWER SEATS - ELECTRICAL DIAGNOSTICS

8N - 227

 

 

 

 

 

 

 

Content   ..  514  515  516  517   ..