Jeep Grand Cherokee WK. Manual - part 488

 

  Index      Jeep     Jeep Grand Cherokee WK - service repair manual 2005 year

 

Search            

 

 

 

 

 

 

 

 

 

Content   ..  486  487  488  489   ..

 

 

Jeep Grand Cherokee WK. Manual - part 488

 

 

B1D04–MIRROR ADJUST SWITCH INPUT CIRCUIT/PERFORMANCE – DRIVER MEMORY MIRROR
MODULE (CONTINUED)

For the Power Memory Mirror System circuit diagram (Refer to 8 - ELECTRICAL/POWER MIRRORS - SCHEMAT-
ICS AND DIAGRAMS).

For a complete wiring diagram Refer to Section 8W.

When Monitored:
When mirror operation is requested.

Set Condition:
If he Driver Memory Mirror Module senses an open or a short to ground for more than 100 ms on the (P703)
Mirror Horizontal Left Switch Sense circuit, the (P76) Mirror Common Driver circuit, the (P705) Mirror Vertical
Down Switch Sense circuit, the (P704) Mirror Horizontal Right Switch Sense circuit, or the (P706) Mirror Ver-
tical Up Switch Sense circuit after receiving a request for mirror movement from the switch.

Possible Causes

(P703) MIRROR HORIZONTAL LEFT SWITCH SENSE CIRCUIT OPEN

(P703) MIRROR HORIZONTAL LEFT SWITCH SENSE CIRCUIT SHORTED TO GROUND

(P703) MIRROR HORIZONTAL LEFT SWITCH SENSE CIRCUIT SHORTED TO ANOTHER MIRROR CIRCUIT

(P704) MIRROR HORIZONTAL RIGHT SWITCH SENSE CIRCUIT OPEN

(P704) MIRROR HORIZONTAL RIGHT SWITCH SENSE CIRCUIT SHORTED TO GROUND

(P704) MIRROR HORIZONTAL RIGHT SWITCH SENSE CIRCUIT SHORTED TO ANOTHER MIRROR CIRCUIT

(P705) MIRROR VERTICAL DOWN SWITCH SENSE CIRCUIT OPEN

(P705) MIRROR VERTICAL DOWN SWITCH SENSE CIRCUIT SHORTED TO GROUND

(P705) MIRROR VERTICAL DOWN SWITCH SENSE CIRCUIT SHORTED TO ANOTHER MIRROR CIRCUIT

(P706) MIRROR VERTICAL UP SWITCH SENSE CIRCUIT OPEN

(P706) MIRROR VERTICAL UP SWITCH SENSE CIRCUIT SHORTED TO GROUND

(P706) MIRROR VERTICAL UP SWITCH SENSE CIRCUIT SHORTED TO ANOTHER MIRROR CIRCUIT

(P76) MIRROR COMMON SWITCH SENSE CIRCUIT OPEN

(P76) MIRROR COMMON SWITCH SENSE CIRCUIT SHORTED TO GROUND

(P76) MIRROR COMMON SWITCH SENSE CIRCUIT SHORTED TO ANOTHER MIRROR CIRCUIT

MIRROR SWITCH

DRIVER MEMORY MIRROR MODULE

Diagnostic Test

1.

TEST FOR INTERMITTENT CONDITION

Turn the ignition on.

With the scan tool, record and erase DTCs.

Press the Mirror Switch in all directions several times.

Cycle the ignition from on to off 3 times.

Turn the ignition on.

With the scan tool, read DTCs.

Does the scan tool display: B1D04 MIRROR ADJUST SWITCH INPUT CIRCUIT/PERFORMANCE?

Yes

>> Go To 2

No

>> The conditions that caused this code to set are not present at this time. Using the wiring diagram/sche-

matic as a guide, inspect the wiring and connectors. If the conditions returns, replace the switch.

Perform BODY VERIFICATION TEST – VER 1. (Refer to 8 - ELECTRICAL/ELECTRONIC CONTROL
MODULES - STANDARD PROCEDURE).

8N - 112

POWER MIRRORS - ELECTRICAL DIAGNOSTICS

WK

B1D04–MIRROR ADJUST SWITCH INPUT CIRCUIT/PERFORMANCE – DRIVER MEMORY MIRROR
MODULE (CONTINUED)

2.

TEST THE MIRROR SWITCH

Turn the ignition off.

Remove the Mirror Switch in accordance with the Service Information.

Disconnect the Mirror Switch connector.

Test the Mirror Switch in all positions in accordance with the Service information. (Refer to 8 - ELECTRICAL/
POWER MIRRORS/POWER MIRROR SWITCH - DIAGNOSIS AND TESTING).

Does the switch pass the test in all positions?

Yes

>> Go To 3

No

>> Replace the Mirror Switch in accordance with the Service information.

Perform BODY VERIFICATION TEST – VER 1. (Refer to 8 - ELECTRICAL/ELECTRONIC CONTROL
MODULES - STANDARD PROCEDURE).

3.

CHECK THE (P703) MIRROR HORIZONTAL LEFT SWITCH SENSE CIRCUIT, THE (P76) MIRROR
COMMON DRIVER CIRCUIT, THE (P705) MIRROR VERTICAL DOWN SWITCH SENSE CIRCUIT, THE
(P704) MIRROR HORIZONTAL RIGHT SWITCH SENSE CIRCUIT, & THE (P706) MIRROR VERTICAL UP
SWITCH SENSE CIRCUIT FOR A SHORT TO GROUND

Disconnect the Driver Memory Mirror Module C2 connector.

Measure the resistance between ground and the (P703) Mirror Hori-
zontal Left Switch Sense circuit, the (P76) Mirror Common Driver cir-
cuit, the (P705) Mirror Vertical Down Switch Sense circuit, the (P704)
Mirror Horizontal Right Switch Sense circuit, and the (P706) Mirror
Vertical Up Switch Sense circuit in the Driver Memory Mirror Module
C2 connector.

Is the resistance below 10000.0 ohms on any of the circuits?

Yes

>> Repair all circuits with a resistance below 10000.0 ohms

for a short to ground.

Perform BODY VERIFICATION TEST – VER 1. (Refer to 8
- ELECTRICAL/ELECTRONIC CONTROL MODULES -
STANDARD PROCEDURE).

No

>> Go To 4

WK

POWER MIRRORS - ELECTRICAL DIAGNOSTICS

8N - 113

B1D04–MIRROR ADJUST SWITCH INPUT CIRCUIT/PERFORMANCE – DRIVER MEMORY MIRROR
MODULE (CONTINUED)

4.

CHECK THE (P703) MIRROR HORIZONTAL LEFT SWITCH SENSE CIRCUIT FOR AN OPEN

Measure the resistance of the (P703) Mirror Horizontal Left Switch
Sense circuit between the Driver Memory Mirror Module C2 connector
and the Mirror Switch connector.

Is the resistance below 2.0 ohms?

Yes

>> Go To 5

No

>> Repair the (P703) Mirror Horizontal Left Switch Sense cir-

cuit for an open.

Perform BODY VERIFICATION TEST – VER 1. (Refer to 8
- ELECTRICAL/ELECTRONIC CONTROL MODULES -
STANDARD PROCEDURE).

8N - 114

POWER MIRRORS - ELECTRICAL DIAGNOSTICS

WK

B1D04–MIRROR ADJUST SWITCH INPUT CIRCUIT/PERFORMANCE – DRIVER MEMORY MIRROR
MODULE (CONTINUED)

5.

CHECK THE (P76) MIRROR COMMON DRIVER CIRCUIT FOR AN OPEN

Measure the resistance of the (P76) Mirror Common Driver circuit
between the Driver Memory Mirror Module C2 connector and the Mir-
ror Switch connector.

Is the resistance below 2.0 ohms?

Yes

>> Go To 6

No

>> Repair the (P76) Mirror Common Driver circuit for an

open.

Perform BODY VERIFICATION TEST – VER 1. (Refer to 8
- ELECTRICAL/ELECTRONIC CONTROL MODULES -
STANDARD PROCEDURE).

WK

POWER MIRRORS - ELECTRICAL DIAGNOSTICS

8N - 115

 

 

 

 

 

 

 

Content   ..  486  487  488  489   ..