Jeep Grand Cherokee WK. Manual - part 486

 

  Index      Jeep     Jeep Grand Cherokee WK - service repair manual 2005 year

 

Search            

 

 

 

 

 

 

 

 

 

Content   ..  484  485  486  487   ..

 

 

Jeep Grand Cherokee WK. Manual - part 486

 

 

B1D0F, B1D18–MIRROR HORIZONTAL POSITION SENSOR INPUT CIRCUIT LOW –
MEMORY MIRROR MODULE

8N - 104

POWER MIRRORS - ELECTRICAL DIAGNOSTICS

WK

B1D0F, B1D18–MIRROR HORIZONTAL POSITION SENSOR INPUT CIRCUIT LOW – MEMORY MIRROR
MODULE (CONTINUED)

For the Power Memory Mirror System circuit diagram (Refer to 8 - ELECTRICAL/POWER MIRRORS - SCHEMAT-
ICS AND DIAGRAMS).

For a complete wiring diagram Refer to Section 8W.

When Monitored:
Continuously

Set Condition:
The (P65) Driver Mirror Horizontal Position Signal circuit supplies input to the Driver Memory Mirror Module.
DTC B1D0F will set if the input value is less than the known good (stored) value for more than 60 ms.
The (P68) Passenger Mirror Horizontal Position Signal circuit supplies input to the Passenger Memory Mirror
Module. DTC B1D18 will set if the input value is less than the known good (stored) value for more than 60 ms.

Possible Causes

FOR THE DRIVER MEMORY MIRROR SYSTEM:

(P65) DRIVER MIRROR HORIZONTAL POSITION SIGNAL CIRCUIT SHORTED TO GROUND

(P65) DRIVER MIRROR HORIZONTAL POSITION SIGNAL CIRCUIT SHORTED TO (Z911) GROUND CIRCUIT

(P65) DRIVER MIRROR HORIZONTAL POSITION SIGNAL CIRCUIT SHORTED TO (P69) DRIVER MIRROR
SENSOR GROUND CIRCUIT

(P65) DRIVER MIRROR HORIZONTAL POSITION SIGNAL CIRCUIT SHORTED TO (C910) DRIVER MIRROR
HEATER GROUND CIRCUIT

DRIVER OUTSIDE REARVIEW MIRROR SHORTED

DRIVER MEMORY MIRROR MODULE

FOR THE PASSENGER MEMORY MIRROR SYSTEM:

(P68) PASSENGER MIRROR HORIZONTAL POSITION SIGNAL CIRCUIT SHORTED TO GROUND

(P68) PASSENGER MIRROR HORIZONTAL POSITION SIGNAL CIRCUIT SHORTED TO (Z908) GROUND
CIRCUIT

(P68) PASSENGER MIRROR HORIZONTAL POSITION SIGNAL CIRCUIT SHORTED TO (P66) PASSENGER
MIRROR SENSOR GROUND CIRCUIT

(P68) PASSENGER MIRROR HORIZONTAL POSITION SIGNAL CIRCUIT SHORTED TO (C917) PASSENGER
MIRROR HEATER GROUND CIRCUIT

PASSENGER OUTSIDE REARVIEW MIRROR SHORTED

PASSENGER MEMORY MIRROR MODULE

NOTE: This procedure addresses the Driver Memory Mirror system’s circuits and components and the Pas-
senger Memory Mirror system’s circuits and components. Select only that which applies to the system you
are diagnosing.

WK

POWER MIRRORS - ELECTRICAL DIAGNOSTICS

8N - 105

B1D0F, B1D18–MIRROR HORIZONTAL POSITION SENSOR INPUT CIRCUIT LOW – MEMORY MIRROR MOD-
ULE (CONTINUED)

Diagnostic Test

1.

TEST FOR INTERMITTENT CONDITION

Turn the ignition on.

With the scan tool, record and erase DTCs.

Operate the Mirror Switch in all directions several times.

Cycle the ignition from on to off 3 times.

Turn the ignition on.

With the scan tool, read DTCs.

Does the scan tool display: B1D0F or B1D18 MIRROR HORIZONTAL POSITION SENSOR INPUT CIRCUIT
LOW?

Yes

>> Go To 2

No

>> The conditions that caused this code to set are not present at this time. Using the wiring diagram/sche-

matic as a guide, inspect the wiring and connectors.

Perform BODY VERIFICATION TEST – VER 1. (Refer to 8 - ELECTRICAL/ELECTRONIC CONTROL
MODULES - STANDARD PROCEDURE).

2.

TEST FOR A SHORTED OUTSIDE REARVIEW MIRROR

For the Driver Memory Mirror System, proceed as follows:

Turn the ignition off.

Disconnect the Driver Outside Rearview Mirror connector.

Turn the ignition on.

With the scan tool, erase DTCs.

Operate the Mirror Switch in all directions several times.

Cycle the ignition from on to off 3 times.

Turn the ignition on.

With the scan tool, read DTCs.

For the Passenger Memory Mirror System, proceed as follows:

Turn the ignition off.

Disconnect the Passenger Outside Rearview Mirror connector.

Turn the ignition on.

With the scan tool, erase DTCs.

Operate the Mirror Switch in all directions several times.

Cycle the ignition from on to off 3 times.

Turn the ignition on.

With the scan tool, read DTCs.

Does the scan tool display: B1D0F or B1D18 MIRROR HORI-
ZONTAL POSITION SENSOR INPUT CIRCUIT LOW?

Yes

>> Go To 3

No

>> Replace the Outside Rearview Mirror in accordance with the Service Information.

Perform BODY VERIFICATION TEST – VER 1. (Refer to 8 - ELECTRICAL/ELECTRONIC CONTROL
MODULES - STANDARD PROCEDURE).

8N - 106

POWER MIRRORS - ELECTRICAL DIAGNOSTICS

WK

B1D0F, B1D18–MIRROR HORIZONTAL POSITION SENSOR INPUT CIRCUIT LOW – MEMORY MIRROR MOD-
ULE (CONTINUED)

3.

CHECK THE (P65) DRIVER MIRROR HORIZONTAL POSITION SIGNAL CIRCUIT OR THE (P68)
PASSENGER MIRROR HORIZONTAL POSITION SIGNAL CIRCUIT FOR A SHORT TO GROUND

For the Driver Memory Mirror System, proceed as follows:

Turn the ignition off.

Disconnect the Driver Memory Mirror Module C1 connector.

Measure the resistance between ground and the (P65) Driver
Mirror Horizontal Position Signal circuit in the Driver Memory Mir-
ror Module C1 connector.

For the Passenger Memory Mirror System, proceed as follows:

Turn the ignition off.

Disconnect the Passenger Memory Mirror Module connector.

Measure the resistance between ground and the (P68) Passen-
ger Mirror Horizontal Position Signal circuit in the Passenger
Memory Mirror Module connector.

Is the resistance below 10000.0 ohms?

Yes, Driver MMM

Repair the (P65) Driver Mirror Horizontal Position Signal
circuit for a short to ground.

Perform BODY VERIFICATION TEST – VER 1. (Refer to 8
- ELECTRICAL/ELECTRONIC CONTROL MODULES -
STANDARD PROCEDURE).

Yes, Passenger MMM

Repair the (P68) Passenger Mirror Horizontal Position Sig-
nal circuit for a short to ground.

Perform BODY VERIFICATION TEST – VER 1. (Refer to 8
- ELECTRICAL/ELECTRONIC CONTROL MODULES -
STANDARD PROCEDURE).

No

>> Go To 4

WK

POWER MIRRORS - ELECTRICAL DIAGNOSTICS

8N - 107

 

 

 

 

 

 

 

Content   ..  484  485  486  487   ..