Jeep Grand Cherokee WK. Manual - part 381

 

  Index      Jeep     Jeep Grand Cherokee WK - service repair manual 2005 year

 

Search            

 

 

 

 

 

 

 

 

 

Content   ..  379  380  381  382   ..

 

 

Jeep Grand Cherokee WK. Manual - part 381

 

 

B1098-FRONT RIGHT SEAT HEATER CONTROL CIRCUIT OPEN (CONTINUED)

For the Heated Seat System circuit diagram (Refer to 8 - ELECTRICAL/HEATED SEATS - SCHEMATICS AND DIA-
GRAMS)

For a complete wiring diagram Refer to Section 8W.

When Monitored:Ignition on, during the heated seat operation.

Set Condition:This code is set immediately after the Heated Seat Module detects an open in the seat heater
B(+) driver circuit.

Possible Causes

RIGHT SEAT HEATER B(+) DRIVER WIRE OPEN

GROUND WIRE OPEN

SEAT CUSHION HEATER ELEMENT OPEN

SEAT BACK HEATER ELEMENT OPEN

HEATED SEAT MODULE

Diagnostic Test

1.

VERIFY THAT DTC B1098-FRONT RIGHT SEAT HEATER CONTROL CIRCUIT OPEN IS ACTIVE

With the scan tool, record and erase DTC’s

Operate the Heated Seat Switch in both positions several times.

With the scan tool, read DTC’s.

Does the DTC B1098 FRONT RIGHT SEAT HEATER CONTROL CIRCUIT OPEN reset?

Yes

>> Go To 2

No

>> The conditions that caused this code to set are not present at this time. Using the wiring diagram/sche-

matic as a guide, inspect the wiring and connectors.

Perform BODY VERIFICATION TEST – VER 1.

8G - 30

HEATED SEATS - ELECTRICAL DIAGNOSTICS

WK

B1098-FRONT RIGHT SEAT HEATER CONTROL CIRCUIT OPEN (CONTINUED)

2.

CHECK FOR AN OPEN SEAT HEATER B(+) DRIVER FROM HSM TO SEAT CUSHION

Disconnect the Right Cushion Pad Heater 2 – way connector.

Disconnect the Heated Seat Module 6 – way connector.

NOTE: Check connectors - Clean and repair as necessary.
Measure the resistance of the Right Seat Heater B(+) Driver circuit
from the HSM 6 – way to the Cushion Pad Heater 2 – way connector.

Is the resistance below 2 ohms?

Yes

>> Go To 3

No

>> Repair the open Seat Heater B(+) Driver circuit.

Perform BODY VERIFICATION TEST – VER 1.

3.

CHECK THE RIGHT SEAT HEATER CUSHION GROUND CIRCUIT

Using a 12-volt test light connected to 12-volts, check the ground cir-
cuit at the Heater Cushion Pad 2 – way connector.

Does the test light illuminate brightly?

Yes

>> Go To 4

No

>> Repair the open ground circuit.

Perform BODY VERIFICATION TEST – VER 1.

WK

HEATED SEATS - ELECTRICAL DIAGNOSTICS

8G - 31

B1098-FRONT RIGHT SEAT HEATER CONTROL CIRCUIT OPEN (CONTINUED)

4.

CHECK THE RIGHT CUSHION PAD HEATER RESISTANCE

Check the resistance of the Cushion Pad Heater element by measur-
ing between the Right Seat Heater B(+) Driver and the Ground circuit
at the 2 – way connector (component side).

Is the resistance above 4.9 ohms?

Yes

>> Replace the seat cushion pad heater element as neces-

sary.

Perform BODY VERIFICATION TEST – VER 1.

No

>> 5

Perform BODY VERIFICATION TEST – VER 1.

5.

CHECK THE RIGHT SEAT BACK HEATER RESISTANCE

Disconnect the Right Seat Back Heater 2 – way connector.

NOTE: Check connectors - Clean and repair as necessary.
Check the resistance of the seat back heater element by measuring
between the Right Seat Heater B(+) Driver and the Ground circuit at
the connector 2 – way (component side).

Is the resistance above 5.5 ohms?

Yes

>> Replace the seat back heater element as necessary.

Perform BODY VERIFICATION TEST – VER 1.

No

>> 6

Perform BODY VERIFICATION TEST – VER 1.

6.

CHECK THE RIGHT SEAT BACK HEATER GROUND CIRCUIT

Using a 12-volt test light connected to 12-volts, check the ground cir-
cuit at the Seat Back Heater 2 – way connector.

Does the test light illuminate brightly?

Yes

>> Go To 7

No

>> Repair the open ground circuit.

Perform BODY VERIFICATION TEST – VER 1.

8G - 32

HEATED SEATS - ELECTRICAL DIAGNOSTICS

WK

B1098-FRONT RIGHT SEAT HEATER CONTROL CIRCUIT OPEN (CONTINUED)

7.

CHECK FOR AN OPEN SEAT HEATER B(+) DRIVER FROM HSM TO SEAT BACK

NOTE: Check connectors - Clean and repair as necessary.
Measure the Right Seat Heater B(+) Driver circuit from the Seat Back
connector to the HSM connector.

Is the resistance below 2.0 ohms?

Yes

>> Replace the Heated Seat Module.

Perform BODY VERIFICATION TEST – VER 1.

No

>> Repair the Right Seat Heater B(+) Driver circuit for an

open back to the splice.

Perform BODY VERIFICATION TEST – VER 1.

WK

HEATED SEATS - ELECTRICAL DIAGNOSTICS

8G - 33

 

 

 

 

 

 

 

Content   ..  379  380  381  382   ..