Jeep Grand Cherokee WK. Manual - part 291

 

  Index      Jeep     Jeep Grand Cherokee WK - service repair manual 2005 year

 

Search            

 

 

 

 

 

 

 

 

 

Content   ..  289  290  291  292   ..

 

 

Jeep Grand Cherokee WK. Manual - part 291

 

 

B2113-5 VOLT SUPPLY CIRCUIT HIGH (FCM) (CONTINUED)

3.

(F891) 5 VOLT SUPPLY CIRCUIT SHORTED TO VOLTAGE

Turn the ignition off.

Disconnect the FCM C1 harness connector.

Turn the ignition on.

Measure the voltage of the (F891) 5 Volt Supply circuit.

Is the voltage above 5.5 volts?

Yes

>> Repair the (F891) 5 Volt Supply circuit for a short to volt-

age.

Perform BODY VERIFICATION TEST – VER 1. (Refer to 8
- ELECTRICAL/ELECTRONIC CONTROL MODULES -
STANDARD PROCEDURE).

No

>> Inspect the wiring and connectors for damage or shorted

circuits. If ok, replace and program the Front Control Mod-
ule in accordance with the service information.

Perform BODY VERIFICATION TEST – VER 1. (Refer to 8
- ELECTRICAL/ELECTRONIC CONTROL MODULES -
STANDARD PROCEDURE).

8E - 10

ELECTRONIC CONTROL MODULES - ELECTRICAL DIAGNOSTICS

WK

B2206-CURRENT VIN MISSING/MISMATCH

For a complete wiring diagram Refer to Section 8W.

When Monitored:
With the ignition on.

Set Condition:
The Front Control Module will receive and monitor the VIN message from the PCM and record the VIN if
different from the last VIN.

Possible Causes

INCORRECT VIN PROGRAMMED IN PCM

FRONT CONTROL MODULE

Diagnostic Test

1.

CHECK FOR ACTIVE DTC

With the scan tool, read the active DTC’s.

Cycle the ignition switch from off to on at least 5 times, leaving the ignition on for a minimum of 90 seconds per
cycle.

With the scan tool, read the active DTC’s.

Does the scan tool display this DTC as active?

Yes

>> Go To 2

No

>> If the DTC is stored, check for an intermittent condition. Visually inspect the related wiring harness con-

nectors. Look for broken, bent, pushed out, or corroded terminals.

2.

CHECK VIN IN PCM

With the scan tool compare the VIN that is programmed into the PCM to the VIN on the vehicle.

Does the VIN programmed into the PCM match the vehicles VIN?

Yes

>> Inspect the wiring and connectors for damage or shorted circuits. If ok, replace and program the Front

Control Module in accordance with the service information.

Perform BODY VERIFICATION TEST – VER 1. (Refer to 8 - ELECTRICAL/ELECTRONIC CONTROL
MODULES - STANDARD PROCEDURE).

No

>> Program the correct VIN in the PCM and retest.

WK

ELECTRONIC CONTROL MODULES - ELECTRICAL DIAGNOSTICS

8E - 11

B2215-FRONT CONTROL MODULE INTERNAL

For a complete wiring diagram Refer to Section 8W.

When Monitored:
Continuously.

Set Condition:
The Front Control Module detects an internal fault.

Possible Causes

FRONT CONTROL MODULE

Diagnostic Test

1.

REPLACE THE FRONT CONTROL MODULE IF DTC IS ACTIVE

With the scan tool, read the active DTC’s.

Does the scan tool display this DTC as active?

Yes

>> Replace and program the Front Control Module in accordance with the service information.

Perform BODY VERIFICATION TEST – VER 1. (Refer to 8 - ELECTRICAL/ELECTRONIC CONTROL
MODULES - STANDARD PROCEDURE).

No

>> If the DTC is stored, check for an intermittent condition. Visually inspect the related wiring harness con-

nectors. Look for broken, bent, pushed out, or corroded terminals.

8E - 12

ELECTRONIC CONTROL MODULES - ELECTRICAL DIAGNOSTICS

WK

B222C-VEHICLE CONFIGURATION NOT PROGRAMMED

For a complete wiring diagram Refer to Section 8W.

When Monitored:
With the ignition on.

Set Condition:
The Front Control Module is not configured correctly to the vehicle.

Possible Causes

FRONT CONTROL MODULE NOT CONFIGURED CORRECTLY

FRONT CONTROL MODULE

Diagnostic Test

1.

CHECK FOR ACTIVE DTC

With the scan tool, read the active DTC’s.

Cycle the ignition switch from off to on at least 5 times, leaving the ignition on for a minimum of 90 seconds per
cycle.

With the scan tool, read the active DTC’s.

Does the scan tool display this DTC as active?

Yes

>> Go To 2

No

>> If the DTC is stored, check for an intermittent condition. Visually inspect the related wiring harness con-

nectors. Look for broken, bent, pushed out, or corroded terminals.

2.

CONFIGURE THE FCM TO THE VEHICLE

With the scan tool enter program network configuration and program the FCM to the vehicle configuration.

With the scan tool, erase FCM DTC’s.

Cycle the ignition switch from off to on at least 5 times, leaving the ignition on for a minimum of 90 seconds per
cycle.

With the scan tool, read the active DTC’s.

Does the scan tool display this DTC as active?

Yes

>> Inspect the wiring and connectors for damage or shorted circuits. If ok, replace and program the Front

Control Module in accordance with the service information.

Perform BODY VERIFICATION TEST – VER 1. (Refer to 8 - ELECTRICAL/ELECTRONIC CONTROL
MODULES - STANDARD PROCEDURE).

No

>> Repair is complete.

WK

ELECTRONIC CONTROL MODULES - ELECTRICAL DIAGNOSTICS

8E - 13

 

 

 

 

 

 

 

Content   ..  289  290  291  292   ..