Jeep Grand Cherokee WK. Manual - part 178

 

  Index      Jeep     Jeep Grand Cherokee WK - service repair manual 2005 year

 

Search            

 

 

 

 

 

 

 

 

 

Content   ..  176  177  178  179   ..

 

 

Jeep Grand Cherokee WK. Manual - part 178

 

 

C2114-SENSOR CLUSTER SUPPLY VOLTAGE LOW (CONTINUED)

6.

(G4) SENSOR CLUSTER SUPPLY CIRCUIT OPEN

Turn the ignition off.

Measure the resistance of the (G4) Sensor Cluster Supply circuit.

Is the resistance below 5.0 ohms?

Yes

>> Replace the Anti-Lock Brake Module in accordance with

the Service Information.

Perform ABS VERIFICATION TEST - VER 1.

No

>> Repair the (G4) Sensor Cluster Supply circuit for an open.

Perform ABS VERIFICATION TEST - VER 1.

7.

SENSOR CLUSTER

Turn the ignition off.

Measure the resistance between the (G94) Sensor Cluster Ground Cir-
cuit and Ground.

Is the resistance below 5.0 ohms?

Yes

>> Replace the Sensor Cluster in accordance with the Ser-

vice Information.

Perform ABS VERIFICATION TEST - VER 1.

No

>> Go To 8

5 - 338

BRAKES - BRAKE CONTROLLER ELECTRICAL DIAGNOSTICS

WK

C2114-SENSOR CLUSTER SUPPLY VOLTAGE LOW (CONTINUED)

8.

(G94) SENSOR CLUSTER GROUND CIRCUIT SHORT TO VOLTAGE

Turn the ignition off.

Disconnect the Anti-Lock Brake Module harness connector.

Turn the ignition on.

Measure the voltage of the (G94) Sensor Cluster Ground circuit.

Is there any voltage present?

Yes

>> Repair the (G94) Sensor Cluster Ground circuit for a short

to voltage.

Perform ABS VERIFICATION TEST - VER 1.

No

>> Go To 9

9.

(G94) SENSOR CLUSTER GROUND CIRCUIT OPEN

Turn the ignition off.

Measure the resistance of the (G94) Sensor Cluster Ground Circuit.

Is the resistance below 5.0 ohms?

Yes

>> Replace the Anti-Lock Brake Module in accordance with

the Service Information.

Perform ABS VERIFICATION TEST - VER 1.

No

>> Repair the (G94) Sensor Cluster Ground circuit for an

open.

Perform ABS VERIFICATION TEST - VER 1.

WK

BRAKES - BRAKE CONTROLLER ELECTRICAL DIAGNOSTICS

5 - 339

C2115-SENSOR CLUSTER SUPPLY VOLTAGE HIGH

5 - 340

BRAKES - BRAKE CONTROLLER ELECTRICAL DIAGNOSTICS

WK

C2115-SENSOR CLUSTER SUPPLY VOLTAGE HIGH (CONTINUED)

For the Anti-Lock Brake System circuit diagram. (Refer to 5 - BRAKES - SCHEMATICS AND DIAGRAMS)

For a complete wiring diagram Refer to Section 8W.

When Monitored:
With the ignition on.

Set Condition:
When the Anti-Lock Brake Module indicates the operating voltage is out of specified range.

Possible Causes

WIRING HARNESS, TERMINAL, CONNECTOR DAMAGE

CHARGING SYSTEM

(G4) SENSOR CLUSTER SUPPLY CIRCUIT SHORTED TO GROUND OR VOLTAGE

(G94) SENSOR CLUSTER GROUND CIRCUIT SHORTED TO VOLTAGE OR OPEN

SENSOR CLUSTER

ANTI-LOCK BRAKE MODULE

1.

CHECK FOR A DTC C2115-SENSOR CLUSTER SUPPLY VOLTAGE HIGH

NOTE: The Sensor Cluster is the same as the Dynamics sensor.

NOTE: This DTC must be active for the results of this test to be valid.
Turn the ignition on.

With the scan tool, read and record DTC’s.

With the scan tool, read and record Freeze Fame information.

With the scan tool, erase DTC’s.

Cycle the ignition from off to on.

With the scan tool, read and record DTCs

Does the scan tool display: C2115-SENSOR CLUSTER SUPPLY VOLTAGE HIGH?

Yes

>> Go To 2

No

>> Refer to the INTERMITTENT CONDITION diagnostic procedure.

Perform ABS VERIFICATION TEST - VER 1.

2.

CHECK THE WIRING HARNESS, TERMINALS, AND CONNECTORS

Check all related wiring for bruised, chafed, pierced, or partially broken wires.

Check all related connectors for broken, bent, pushed out, or corroded terminals.

Were any problems found?

Yes

>> Repair as necessary.

Perform ABS VERIFICATION TEST - VER 1.

No

>> Go To 3

WK

BRAKES - BRAKE CONTROLLER ELECTRICAL DIAGNOSTICS

5 - 341

 

 

 

 

 

 

 

Content   ..  176  177  178  179   ..