Jeep Grand Cherokee WK. Manual - part 1750

 

  Index      Jeep     Jeep Grand Cherokee WK - service repair manual 2005 year

 

Search            

 

 

 

 

 

 

 

 

 

Content   ..  1748  1749  1750  1751   ..

 

 

Jeep Grand Cherokee WK. Manual - part 1750

 

 

*HVAC SYSTEM TEST (ATC) (CONTINUED)

2.

A/C SYSTEM PERFORMANCE TEST

NOTE: The following are prerequisites of the Cooldown Test. Verify each of the following before running the
test:

If active, diagnose and repair DTC B1031 or B1032 before proceeding. Refer to the Table of Contents in
this Section for a complete list of HVAC related symptoms.

Verify that the refrigerant system has an adequate charge. Check and repair as necessary before pro-
ceeding. (Refer to 24 - HEATING & AIR CONDITIONING/PLUMBING - DIAGNOSIS AND TESTING - REFRIG-
ERANT SYSTEM LEAKS).

Verify that the blower motor operates correctly in all speeds. Diagnose and repair all blower related faults
before proceeding.

Verify that the work area ambient temperature is above 18.3°C (65°F) before proceeding. Move the vehicle
to a warmer work area if necessary.

Verify that the evaporator temperature is above 18.3°C (65°F) before proceeding.

Verify that the A/C compressor is not running. If the A/C compressor is running, turn the A/C off and
allow the evaporator to warm up before proceeding.

Once all of the prerequisites have been met, actuate the Cooldown Test by performing the following:

Start the engine.

With the scan tool in HVAC, select System Tests and then select Cooldown test.

NOTE: The Cooldown Test can take up to two minutes to run. While the test is running, the A/C status
indicator will flash. If the test passes, the A/C status indicator will stop flashing. However, if the test fails,
both the A/C and EBL status indicators will flash alternately and an active DTC B10B2 will set. The status
indicators will continue to flash until either a successful Cooldown Test is executed or until the vehicle is
driven a specified number of miles. In addition, DTC B10B2 will remain active until a successful Cooldown
Test is executed. The test will stop running if any of the following occurs:

The ignition is turned off.

The A/C compressor is requested off.

The blower control is moved to the off position, unless the control was in the off position when the test
was started. In this case, moving the blower control out of the off position and then returning it to the off
position will stop the test

DTC B1031 or B1032 sets during the test.

the control receives a bus message to stop the test.

Allow the test to run to completion before proceeding.

With the scan tool, select View DTCs.

Does the scan tool display any DTCs?

Yes

>> Diagnose and Repair the DTC(s). Refer to the Table of Contents in this Section for a complete list of

HVAC related symptoms. Run the Cooldown Test again after the repair is complete.

No

>> As necessary, either Go To 3, or 4, or 5, or Perform BODY VERIFICATION TEST – VER 1. (Refer to 8

- ELECTRICAL/ELECTRONIC CONTROL MODULES - STANDARD PROCEDURE).

24 - 348

HVAC - ELECTRICAL DIAGNOSTICS

WK

*HVAC SYSTEM TEST (ATC) (CONTINUED)

3.

GENERAL SYSTEM OPERATION & FUNCTION TEST

NOTE: If at anytime a DTC becomes active during this test, proceed to the conclusion question.

NOTE: If multiple DTCs become active, diagnose those that relate to a short circuit first.
If not do so previously, start the engine.

Turn the blower control to manual low.

Turn the Left and Right Blend controls to full cold.

Turn the Mode control to panel.

Monitor the scan tool for active HVAC DTCs while performing the following test steps.

Press the A/C mode switch on, wait 30 seconds, press it off, and then proceed to the next step.

Press the Rear Defrost mode switch on, wait 30 seconds, press it off, and then proceed to the next step.

Press the Recirculation mode switch on, wait 30 seconds, press it off, and then proceed to the next step.

Turn the Left Blend control to full hot, wait 30 seconds, turn it to full cold, and then proceed to the next step.

Turn the Right Blend control to full hot, wait 30 seconds, turn it to full cold, and then proceed to the next step.

Turn the Mode control to every door position. Leave it in each position for 30 seconds.

Does the scan tool display any active DTCs?

Yes

>> Diagnose and repair the DTC(s). Refer to the Table of Contents in this Section for a complete list of

HVAC related symptoms.

No

>> If you are here due to a stored DTC, it is possible that a technician may not have erased the DTC

following a repair. If possible, verify if the vehicle was recently in for this type of service. Otherwise, Go
To either or 5, or visually inspect the related wiring harness for chafed, pierced, pinched, and partially
broken wires and the wiring harness connectors for broken, bent, pushed out, and corroded terminals,
and repair as necessary.

Perform BODY VERIFICATION TEST – VER 1. (Refer to 8 - ELECTRICAL/ELECTRONIC CONTROL
MODULES - STANDARD PROCEDURE).

4.

ACTUATOR DTC DETECTION TEST

If not done so previously, start the engine.

With the scan tool, select System Tests and then select Actuator DTC Detection. When the test is complete, select
View DTCs.

Does the scan tool display any DTCs?

Yes

>> Diagnose and repair the DTC(s). If multiple DTCs are present, diagnose and repair all short high DTCs

and then all short low DTCs. Refer to the Table of Contents in this Section for a complete list of all
HVAC related symptoms.

No

>> If you are here due to a stored DTC, it is possible that a technician may not have erased the DTC

following a repair. If possible, verify if the vehicle was recently in for this type of service. Otherwise,
either Go To or visually inspect the related wiring harness for chafed, pierced, pinched, and partially
broken wires and the wiring harness connectors for broken, bent, pushed out, and corroded terminals,
and repair as necessary.

Perform BODY VERIFICATION TEST – VER 1. (Refer to 8 - ELECTRICAL/ELECTRONIC CONTROL
MODULES - STANDARD PROCEDURE).

WK

HVAC - ELECTRICAL DIAGNOSTICS

24 - 349

*HVAC SYSTEM TEST (ATC) (CONTINUED)

5.

ACTUATOR CALIBRATION TEST

If not done so previously, start the engine.

With the scan tool, select System Tests and then select Actuator Calibration Test. When the test is complete, select
View DTCs.

Does the scan tool display any DTCs?

Yes

>> Diagnose and repair the DTC(s). Refer to the Table of Contents in this Section for a complete list of all

HVAC related symptoms.

No

>> No problem found. However, if you are here due to a stored DTC, it is possible that a technician may

not have erased the DTC following a repair. If possible, verify if the vehicle was recently in for this type
of service. Otherwise, visually inspect the related wiring harness for chafed, pierced, pinched, and par-
tially broken wires and the wiring harness connectors for broken, bent, pushed out, and corroded ter-
minals, and repair as necessary.

Perform BODY VERIFICATION TEST – VER 1. (Refer to 8 - ELECTRICAL/ELECTRONIC CONTROL
MODULES - STANDARD PROCEDURE).

24 - 350

HVAC - ELECTRICAL DIAGNOSTICS

WK

*HVAC SYSTEM TEST (MTC)

For the Manual Temperature Control (MTC) circuit diagram (Refer to 24 - HEATING & AIR CONDITIONING - SCHE-
MATICS AND DIAGRAMS).

For a complete wiring diagram Refer to Section 8W.

Theory of Operation

The HVAC System Test provides a starting point in the diagnostic process by identifying the appropriate diagnostic
procedure or system test to perform when diagnosing a given symptom, condition, or DTC. It also provides a means
for testing the entire HVAC system by utilizing the A/C Heater Control’s On-Board System Tests. The On-Board
System Tests can also assist in diagnosing stored DTCs. (Refer to 24 - HEATING & AIR CONDITIONING - DIAG-
NOSIS AND TESTING) for additional information about on-board diagnostics.

Diagnostic Test

1.

HVAC SYSTEM TEST

NOTE: Diagnose and repair all active DTCs before diagnosing and repairing stored DTCs.

Make a selection based on the symptom, condition, or DTC that you want to diagnose.

For Any Active DTC

Refer to the Table of Contents in this Section for a complete list of all HVAC related symptoms.

Complete HVAC System Test

Go To 2

A/C System Performance Test

Go To 2

General System Operation & Function Test

Go To 3

Actuator Ckt Test / Door Cal Function

Go To 4

Control Won’t Display Active / Stored DTCs

Refer to *A/C Heater Control Will Not Enter Diagnostic Mode for the diagnostic test procedure.

Control Won’t Run System Tests

Refer to *A/C Heater Control Will Not Enter Diagnostic Mode for the diagnostic test procedure.

WK

HVAC - ELECTRICAL DIAGNOSTICS

24 - 351

 

 

 

 

 

 

 

Content   ..  1748  1749  1750  1751   ..