Jeep Grand Cherokee WK. Manual - part 1535

 

  Index      Jeep     Jeep Grand Cherokee WK - service repair manual 2005 year

 

Search            

 

 

 

 

 

 

 

 

 

Content   ..  1533  1534  1535  1536   ..

 

 

Jeep Grand Cherokee WK. Manual - part 1535

 

 

C1414–NEUTRAL SELECT SWITCH CIRCUIT STUCK

21 - 950

TRANSFER CASE - ELECTRICAL DIAGNOSTICS

WK

C1414–NEUTRAL SELECT SWITCH CIRCUIT STUCK (CONTINUED)

For a complete wiring diagram Refer to Section 8W

When Monitored:
With the ignition on and no system undervoltage or overvoltage condition present.

Set Condition:
Valid voltage for Neutral switch active present for a calibratable time.

Possible Causes

INTERMITTENT NEUTRAL SELECT SWITCH CIRCUIT STUCK DTC

TRANSFER CASE SELECTOR SWITCH

FINAL DRIVE CONTROL MODULE

Diagnostic Test

1.

DTC IS ACTIVE

Turn the ignition on.

With the scan tool, select View DTCs in the Final Drive Control Module.

Is the status Active for this DTC?

Yes

>> Go to 2

No

>> Go to 4

2.

TRANSFER CASE SELECTOR SWITCH

Turn the ignition off.

Disconnect the Transfer Case Selector Switch.

Ignition on, engine not running.

With the scan tool select Data Display and read the 4wd Range
Switch Voltage.

The switch voltage should be approximately 0 volts.

Turn the ignition off.

Connect a jumper wire between the (K504) Drivetrain 5 Volt Supply
circuit and the (K977) Mode Select circuit in the Transfer Case Selec-
tor Switch connector.

Ignition on, engine not running.

With the scan tool, read the 4wd Range Switch Voltage.

The switch voltage should be approximately 5 volts.

Does the voltage display as described?

Yes

>> Replace the Transfer Case Selector Switch.

Perform the TRANSFER CASE VERIFICATION TEST-
VER 1.

No

>> Go To 3

WK

TRANSFER CASE - ELECTRICAL DIAGNOSTICS

21 - 951

C1414–NEUTRAL SELECT SWITCH CIRCUIT STUCK (CONTINUED)

3.

FINAL DRIVE CONTROL MODULE

View repair.

Repair

Replace the Final Drive Control Module in accordance with the Service information.

Perform the TRANSFER CASE VERIFICATION TEST-VER 1.

4.

INTERMITTENT WIRING AND CONNECTORS

The conditions necessary to set this DTC are not present at this time.

Using the wiring diagram/schematic as a guide, inspect the wiring and connectors.

While monitoring the scan tool data relative to this circuit, wiggle test the wiring and connectors.

Look for the data to change or for the DTC to reset during the wiggle test.

Were any problems found?

Yes

>> Repair as necessary.

Perform the TRANSFER CASE VERIFICATION TEST-VER 1.

No

>> Test complete.

21 - 952

TRANSFER CASE - ELECTRICAL DIAGNOSTICS

WK

C1415- TRANSFER CASE MOTOR CURRENT PERFORMANCE

For a complete wiring diagram Refer to Section 8W

When Monitored:
With the ignition on and no system undervoltage or overvoltage condition present.

Set Condition:
1. Current reading greater than 1A for 200 msec with no motor activation.
2. Current reading never greater than 1A during a completed range or neutral shift.

Possible Causes

INTERMITTENT TRANSFER CASE MOTOR CURRENT PERFORMANCE

TRANSFER CASE MOTOR

FINAL DRIVE CONTROL MODULE

Diagnostic Test

1.

DTC IS ACTIVE

Ignition on, engine not running.

With the scan tool, select View DTCs.

Is the status Active for this DTC?

Yes

>> Go to 2

No

>> Go to 4

2.

TRANSFER CASE MOTOR

Turn the ignition off.

Using the wiring diagram/schematic as a guide, inspect all wiring and connectors that pertain to this circuit.

If any problems are found, repair as necessary and retest.

If no other problems are found, replace the Transfer Case Motor in accordance with the Service Information.

Ignition on, engine not running.

Cycle the Transfer Case Selector Switch to each position several times during a test drive.

With the scan tool, select View DTCs.

Is the DTC status Active?

Yes

>> Go to 3

No

>> Test complete.

Perform the TRANSFER CASE VERIFICATION TEST-VER 1.

3.

FINAL DRIVE CONTROL MODULE

Using the wiring diagram/schematic as a guide, inspect all wiring and connectors that pertain to this circuit.

Were any problems found?

Yes

>> Repair as necessary.

Perform the TRANSFER CASE VERIFICATION TEST-VER 1.

No

>> Replace the Final Drive Control Module in accordance with the Service Information.

Perform the TRANSFER CASE VERIFICATION TEST-VER 1.

WK

TRANSFER CASE - ELECTRICAL DIAGNOSTICS

21 - 953

 

 

 

 

 

 

 

Content   ..  1533  1534  1535  1536   ..