Jeep Grand Cherokee WK. Manual - part 1529

 

  Index      Jeep     Jeep Grand Cherokee WK - service repair manual 2005 year

 

Search            

 

 

 

 

 

 

 

 

 

Content   ..  1527  1528  1529  1530   ..

 

 

Jeep Grand Cherokee WK. Manual - part 1529

 

 

C1408-TRANSFER CASE BRAKE CONTROL CIRCUIT HIGH (CONTINUED)

3.

(T317) TRANSFER CASE MOTOR LOCK SIGNAL CIRCUIT SHORTED TO THE (T301) SWITCHED
BATTERY SOLENOID SUPPLY CIRCUIT

Measure the resistance between the (T317) Transfer Case Motor Lock
Signal circuit and the (T301) Switched Battery Solenoid Supply circuit.

Is the resistance below 5.0 ohms?

Yes

>> Repair the (T317) Transfer Case Motor Lock Signal circuit

for a short to the (T301) Switched Battery Solenoid Supply
circuit.

Perform the TRANSFER CASE VERIFICATION TEST-
VER 1.

No

>> Go to 4

4.

TRANSFER CASE MOTOR

Turn the ignition off.

Connect the Final Drive Control Module C1 harness connector.

Turn the ignition on.

With the scan tool, Clear DTCs.

With the scan tool, select View DTCs.

Does the DTC P1407–Transfer Case Brake Control Circuit Low set?

Yes

>> Replace the Transfer Case Motor assembly.

Perform the TRANSFER CASE VERIFICATION TEST-VER 1.

No

>> Go to 5

5.

FINAL DRIVE CONTROL MODULE

View repair.

Repair

Replace the Final Drive Control Module in accordance with the Service Information.

Perform the TRANSFER CASE VERIFICATION TEST-VER 1.

21 - 926

TRANSFER CASE - ELECTRICAL DIAGNOSTICS

WK

C1408-TRANSFER CASE BRAKE CONTROL CIRCUIT HIGH (CONTINUED)

6.

INTERMITTENT WIRING AND CONNECTORS

The conditions necessary to set this DTC are not present at this time.

Using the wiring diagram/schematic as a guide, inspect the wiring and connectors.

While monitoring the scan tool data relative to this circuit, wiggle test the wiring and connectors.

Look for the data to change or for the DTC to reset during the wiggle test.

Were any problems found?

Yes

>> Repair as necessary.

Perform the TRANSFER CASE VERIFICATION TEST-VER 1.

No

>> Test complete.

WK

TRANSFER CASE - ELECTRICAL DIAGNOSTICS

21 - 927

C140A- TRANSFER CASE MOTOR PERFORMANCE

21 - 928

TRANSFER CASE - ELECTRICAL DIAGNOSTICS

WK

C140A- TRANSFER CASE MOTOR PERFORMANCE (CONTINUED)

For a complete wiring diagram Refer to Section 8W

When Monitored:
With the ignition on and no undervoltage or overvoltage condition present.

Set Condition:
A faulted condition is detected in the H-bridge driver.

Possible Causes

INTERMITTENT TRANSFER CASE MOTOR PERFORMANCE DTC

(T315) SHIFT MOTOR CONTROL A CIRCUIT SHORTED TO VOLTAGE

(T316) SHIFT MOTOR CONTROL B CIRCUIT SHORTED TO VOLTAGE

(T315) SHIFT MOTOR CONTROL A CIRCUIT SHORTED TO GROUND

(T316) SHIFT MOTOR CONTROL B CIRCUIT SHORTED TO GROUND

(T315) SHIFT MOTOR CONTROL A CIRCUIT SHORTED TO (T316) SHIFT MOTOR CONTROL B CIRCUIT

TRANSFER CASE MOTOR

FINAL DRIVE CONTROL MODULE

Diagnostic Test

1.

DTC IS ACTIVE

Ignition on, engine not running.

With the scan tool, select View DTCs.

Is the status Active for this DTC?

Yes

>> Go to 2

No

>> Go to 9

2.

(T315) SHIFT MOTOR CONTROL A CIRCUIT SHORTED TO VOLTAGE

Turn the ignition off.

Disconnect the Transfer Case Motor harness connector.

Disconnect the Final Drive Control Module C1 harness connector.

Turn the ignition on.

Measure the voltage of the (T315) Shift Motor Control A circuit.

Is there any voltage present?

Yes

>> Repair the (T315) Shift Motor Control A circuit for a short

to voltage.

Perform the TRANSFER CASE VERIFICATION TEST-
VER 1.

No

>> Go to 3

WK

TRANSFER CASE - ELECTRICAL DIAGNOSTICS

21 - 929

 

 

 

 

 

 

 

Content   ..  1527  1528  1529  1530   ..