Jeep Grand Cherokee WK. Manual - part 1129

 

  Index      Jeep     Jeep Grand Cherokee WK - service repair manual 2005 year

 

Search            

 

 

 

 

 

 

 

 

 

Content   ..  1127  1128  1129  1130   ..

 

 

Jeep Grand Cherokee WK. Manual - part 1129

 

 

U1111-LOST ODOMETER MESSAGE

9 - 1112

ENGINE ELECTRICAL DIAGNOSTICS

WK

U1111-LOST ODOMETER MESSAGE (CONTINUED)

For the Engine circuit diagram (Refer to 9 - ENGINE - SCHEMATICS AND DIAGRAMS).

For a complete wiring diagram Refer to Section 8W.

When Monitored:
Ignition on.

Set Condition:
The PCM doesn’t receive an odometer reading from the cluster through the FCM over CAN C.

Possible Causes

CAN C OPEN OR SHORTED

FRONT CONTROL MODULE

PCM

Always perform the Pre-Diagnostic Troubleshooting procedure before proceeding. (Refer to 9 - ENGINE -
DIAGNOSIS AND TESTING).

Theory of Operation

The PCM receives odometer readings from the Front Control Module over CAN C. The FCM gets the odometer
readings from the Cluster Module over CAN B. U0001-CAN C BUS, and U0141-LOST COMMUNICATION WITH
FCM may also set.

Diagnostic Test

1.

ACTIVE DTC

Ignition on, engine not running.

With the scan tool read Powertrain DTCs.

Is the DTC active at this time?

Yes

>> Go To 2

No

>> Refer to the INTERMITTENT CONDITION Diagnostic Procedure.

Perform the POWERTRAIN VERIFICATION TEST. (Refer to 9 - ENGINE - STANDARD PROCEDURE)

2.

U0141-LOST COMMUNICATION WITH FRONT CONTROL MODULE ALSO ACTIVE

With the scan tool read DTCs.

U0141-LOST COMMUNICATION WITH FRONT CONTROL MODULE also set?

Yes

>> Follow the diagnostics for U0141-LOST COMMUNICATION WITH FRONT CONTROL MODULE

Perform the POWERTRAIN VERIFICATION TEST. (Refer to 9 - ENGINE - STANDARD PROCEDURE)

No

>> Replace and program the Powertrain Control Module per Service Information.

Perform the POWERTRAIN VERIFICATION TEST. (Refer to 9 - ENGINE - STANDARD PROCEDURE)

WK

ENGINE ELECTRICAL DIAGNOSTICS

9 - 1113

U1113-LOST A/C PRESSURE MESSAGE

9 - 1114

ENGINE ELECTRICAL DIAGNOSTICS

WK

U1113-LOST A/C PRESSURE MESSAGE (CONTINUED)

For the Engine circuit diagram (Refer to 9 - ENGINE - SCHEMATICS AND DIAGRAMS).

For a complete wiring diagram Refer to Section 8W.

When Monitored:
Ignition on.

Set Condition:
The PCM doesn’t receive the A/C Pressure signal over the CAN C bus from the FCM. The circuit is continu-
ously monitored.

Possible Causes

CAN C BUS CIRCUIT OPEN OR SHORTED

FRONT CONTROL MODULE

PCM

Always perform the Pre-Diagnostic Troubleshooting procedure before proceeding. (Refer to 9 - ENGINE -
DIAGNOSIS AND TESTING).

Theory of Operation

The A/C Pressure Transducer signal is a direct input to the FCM. The FCM sends the PCM the A/C pressure signal
over the CAN C bus.

Diagnostic Test

1.

ACTIVE DTC

Ignition on, engine not running.

With the scan tool read Powertrain DTCs.

Is the DTC active at this time?

Yes

>> Go To 2

No

>> Refer to the INTERMITTENT CONDITION Diagnostic Procedure.

Perform the POWERTRAIN VERIFICATION TEST. (Refer to 9 - ENGINE - STANDARD PROCEDURE)

2.

U0141-LOST COMMUNICATION WITH FRONT CONTROL MODULE ALSO ACTIVE

With the scan tool read DTCs.

Is the U0141-NO BUS MESSAGE RECEIVED FROM THE FCM also set?

Yes

>> Follow the diagnostics for U0141-LOST COMMUNICATION WITH FRONT CONTROL MODULE

Perform the POWERTRAIN VERIFICATION TEST. (Refer to 9 - ENGINE - STANDARD PROCEDURE)

No

>> Replace and program the Powertrain Control Module per Service Information.

Perform the POWERTRAIN VERIFICATION TEST. (Refer to 9 - ENGINE - STANDARD PROCEDURE)

WK

ENGINE ELECTRICAL DIAGNOSTICS

9 - 1115

 

 

 

 

 

 

 

Content   ..  1127  1128  1129  1130   ..