Jeep Grand Cherokee WK. Manual - part 1010

 

  Index      Jeep     Jeep Grand Cherokee WK - service repair manual 2005 year

 

Search            

 

 

 

 

 

 

 

 

 

Content   ..  1008  1009  1010  1011   ..

 

 

Jeep Grand Cherokee WK. Manual - part 1010

 

 

P0580-SPEED CONTROL SWITCH 1 CIRCUIT LOW (CONTINUED)

For the Engine circuit diagram (Refer to 9 - ENGINE - SCHEMATICS AND DIAGRAMS).

For a complete wiring diagram Refer to Section 8W.

When Monitored:
With the ignition key on.

Set Condition:
Speed control switch input No.1 is below the minimum acceptable voltage at the PCM. One trip fault.

Possible Causes

(V371) S/C SWITCH NO.1 SIGNAL CIRCUIT SHORTED TO THE (V397) S/C SWITCH RETURN

(V71) S/C SWITCH NO.1 SIGNAL CIRCUIT SHORTED TO THE (V937) S/C SWITCH RETURN

(V371) S/C SWITCH NO.1 SIGNAL CIRCUIT SHORTED TO GROUND

(V71) S/C SWITCH NO.1 SIGNAL CIRCUIT SHORTED TO GROUND

STEERING COLUMN CONTROL MODULE

SPEED CONTROL ON/OFF SWITCH

SPEED CONTROL RESUME/ACCEL SWITCH

PCM

Always perform the Pre-Diagnostic Troubleshooting procedure before proceeding. (Refer to 9 - ENGINE -
DIAGNOSIS AND TESTING).

Diagnostic Test

1.

SPEED CONTROL SWITCH VOLTAGE LOW

NOTE: Do not press any of the Speed Control Switch buttons.
Ignition on, engine not running.

With a scan tool, read the Speed Control voltage.

Is the Speed Control voltage below 1.0 volt?

Yes

>> Go To 2

No

>> Refer to the INTERMITTENT CONDITION Diagnostic Procedure.

Perform the POWERTRAIN VERIFICATION TEST. (Refer to 9 - ENGINE - STANDARD PROCEDURE)

9 - 636

ENGINE ELECTRICAL DIAGNOSTICS

WK

P0580-SPEED CONTROL SWITCH 1 CIRCUIT LOW (CONTINUED)

2.

SPEED CONTROL SWITCHES

Turn the ignition off.

Remove and disconnect the Speed Control Switches from the steering wheel per Service Information.

Measure the resistance across each Speed Control Switch.

Monitor the ohmmeter while pressing each function button on each switch.

The following resistance specs are taken between terminals (V371) S/C Switch No.1 Signal and (V397) S/C Switch
Return circuits of the Switch when holding the switch button in the following positions.

Not pressing any switch - 20.5 kohms

On/Off - 0.47 kohms

Set - 5.49 kohms

Coast - 2.94 kohms

Cancel - 1.24 kohms

Resume/Accel - 15.4 kohms

Does the function on the Speed Control Switches have the correct resistance value?

Yes

>> Go To 3

No

>> Replace the Speed Control Switch that had the incorrect resistance value.

Perform the POWERTRAIN VERIFICATION TEST. (Refer to 9 - ENGINE - STANDARD PROCEDURE)

3.

SPEED CONTROL ON/OFF SWITCH

Connect the Resume/Accel Switch.

Ignition on, engine not running.

With the scan tool, monitor the Speed Control Switch voltage.

Disconnect the Speed Control On/Off Switch harness connector.

Did the voltage change to above 4.8 volts?

Yes

>> Replace the Speed Control On/Off Switch.

Perform the POWERTRAIN VERIFICATION TEST. (Refer to 9 - ENGINE - STANDARD PROCEDURE)

No

>> Go To 4

4.

SPEED CONTROL RESUME/ACCEL SWITCH

With the scan tool, monitor the Speed Control Switch voltage.

Disconnect the Speed Control Resume/Accel Switch harness connector per Service Information.

Did the voltage change to above 4.8 volts?

Yes

>> Replace the Speed Control Resume/Accel Switch.

Perform the POWERTRAIN VERIFICATION TEST. (Refer to 9 - ENGINE - STANDARD PROCEDURE)

No

>> Go To 5

WK

ENGINE ELECTRICAL DIAGNOSTICS

9 - 637

P0580-SPEED CONTROL SWITCH 1 CIRCUIT LOW (CONTINUED)

5.

STEERING COLUMN CONTROL MODULE

Turn the ignition off.

Disconnect the C1 SCCM harness connector per Service Information.

Ignition on, engine not running.

With the scan tool, read the S/C Switch voltage.

Did the S/C Switch volts change to 5.0 volts?

Yes

>> Replace the Clockspring.

Perform the POWERTRAIN VERIFICATION TEST. (Refer to 9 - ENGINE - STANDARD PROCEDURE)

No

>> Go To 6

6.

(V371) S/C SWITCH NO.1 SIGNAL CIRCUIT SHORTED TO THE (V397) S/C SWITCH RETURN CIRCUIT

Turn the ignition off.

Disconnect the C3 SCCM harness connector.

Disconnect the C3 PCM harness connector.

Measure the resistance between the (V397) S/C Switch Return circuit
and the (V371) S/C Switch No.1 Signal circuit at the S/C Switch har-
ness connectors.

Is the resistance below 5.0 ohms?

Yes

>> Repair the short between the (V371) S/C Switch No.1 Sig-

nal circuit and the (V397) S/C Switch Return circuit.

Perform the POWERTRAIN VERIFICATION TEST. (Refer
to 9 - ENGINE - STANDARD PROCEDURE)

No

>> Go To 7

7.

(V71) S/C SWITCH NO.1 SIGNAL CIRCUIT SHORTED TO THE (V937) S/C SWITCH RETURN CIRCUIT

Measure the resistance between the (V71) S/C Switch No.1 Signal cir-
cuit and the (V937) S/C Switch Return circuit in the C1 SCCM harness
connector.

Is the resistance below 5.0 ohms?

Yes

>> Repair the short between the (V71) S/C Switch No.1 Sig-

nal circuit and the (V937) Switch Return circuit.

Perform the POWERTRAIN VERIFICATION TEST. (Refer
to 9 - ENGINE - STANDARD PROCEDURE)

No

>> Go To 8

9 - 638

ENGINE ELECTRICAL DIAGNOSTICS

WK

P0580-SPEED CONTROL SWITCH 1 CIRCUIT LOW (CONTINUED)

8.

(V371) S/C SWITCH NO.1 SIGNAL CIRCUIT SHORTED TO GROUND

Measure the resistance between ground and the (V371) S/C Switch
No.1 Signal circuit in the S/C Switch harness connector.

Is the resistance below 100 ohms?

Yes

>> Repair the short to ground in the (V371) S/C Switch No.1

Signal circuit.

Perform the POWERTRAIN VERIFICATION TEST. (Refer
to 9 - ENGINE - STANDARD PROCEDURE)

No

>> Go To 9

9.

(V71) S/C NO.1 SWITCH SIGNAL CIRCUIT SHORTED TO GROUND

Measure the resistance between ground and the (V71) S/C Switch
No.1 Signal circuit in the C1 SCCM harness connector.

Is the resistance below 100 ohms?

Yes

>> Repair the short to ground in the (V71) S/C Switch No.1

Signal circuit.

Perform the POWERTRAIN VERIFICATION TEST. (Refer
to 9 - ENGINE - STANDARD PROCEDURE)

No

>> Go To 10

WK

ENGINE ELECTRICAL DIAGNOSTICS

9 - 639

 

 

 

 

 

 

 

Content   ..  1008  1009  1010  1011   ..