Jeep Grand Cherokee WJ. Manual - part 893

 

  Index      Jeep     Jeep Grand Cherokee WJ - service repair manual 2001 year

 

Search            

 

 

 

 

 

 

 

 

 

Content   ..  891  892  893  894   ..

 

 

Jeep Grand Cherokee WJ. Manual - part 893

 

 

(35) Install seal on park/neutral position switch.

Then install and tighten switch to 34 N·m (25 ft.
lbs.).

(36) Install magnet in oil pan. Magnet goes on

small protrusion at corner of pan.

(37) Position new oil pan gasket on case and

install oil pan. Tighten pan bolts to 17 N·m (13 ft.
lbs.).

(38) Install new valve body manual shaft seal in

case (Fig. 60). Lubricate seal lip and manual shaft
with petroleum jelly. Start seal over shaft and into
case. Seat seal with 15/16 inch, deep well socket.

(39) Install throttle valve and shift selector levers

on valve body manual lever shaft.

INSTALLATION

CAUTION: This engine is equipped with a engine
speed sensor. Located in the top of the bellhousing.
Care must be taken not to damage the sensor or
corresponding wires during transmission removal
and installation.

CAUTION: Check the torque converter hub and hub
drive notches for sharp edges, burrs, scratches or
nicks. Polish the hub and notches with 320 / 400
grit sandpaper, if necessary. The hub must be
smooth to avoid damaging the pump seal at torque
converter installation.

CAUTION: Lubricate the front pump seal and install
at least one quart of the approved transmission
fluid directly into the torque converter prior to its
installation.

(1) Install the torque converter in the transmis-

sion.

(2) Lubricate the rear of the crankshaft or the con-

verter pilot hub with lithium grease.

(3) Position the transmission/converter assembly

on a transmission jack and secure with chains.

NOTE: Be sure the engine block mounted dowel
pins are installed and protrude far enough to hold
the transmission in alignment.

(4) Using the transmission jack, position the trans-

mission assembly so the engine block mounted dowel
pins are perfectly aligned with the corresponding
holes in the transmission bellhousing.

CAUTION: Be certain the torque convertor is prop-
erly installed in the transmission. If the torque con-
vertor is not installed correctly the engine will not
rotate upon installation. Refer to the Torque Con-
verter removal and installation procedure in this
group for the procedure.

(5) Install the (10) engine to transmission bell-

housing retaining bolts. Torque the bolts to 102 N·m
(75 ft. lbs.).

(6) Connect the engine speed sensor. Located on

the upper right side of the transmission bellhousing.

NOTE: When installing the torque convertor to
driveplate retaining bolts, the torque convertor can
be rotated into position with a flat-bladed screw-
driver through the starter motor access hole. Then
working through the torque convertor bolt access
hole, thread a longer than original bolt into the con-
vertor and pull the convertor up against the drive-
plate by hand. Remove the longer bolt and install
the original bolts one by one until all bolts are
installed. Then go back and torque all bolts to spec-
ification.

(7) Rotate the converter so the previously scribed

alignment mark is aligned with the mark on the
driveplate.

(8) Working through the torque convertor bolt

access hole (Fig. 61), install the (4) torque convertor
to driveplate retaining bolts by hand.

(9) Verify that the torque converter is pulled flush

to the driveplate. Torque the bolts to 32 N·m (24 ft.
lbs.).

(10) Install the starter motor in the vehicle. (Refer

to 8 - ELECTRICAL/STARTING/STARTER MOTOR -
INSTALLATION)

(11) Install the exhaust system inlet pipe and

retaining bolts (Fig. 62). Torque the bolts to 41 N·m
(30 ft. lbs.).

Fig. 60 Installing Manual Lever Shaft Seal

1 - 15/16'' SOCKET
2 - SEAL

WG

AUTOMATIC - 44RE

21s - 79

AUTOMATIC - 44RE (Continued)

2001 JEEP GRAND CHEROKEE

(12) Connect the transmission electrical connectors

and clip the wire harness on the transmission hous-
ing.

(13) Install the transmission fluid cooler lines on

the transmission (Fig. 63). Torque the nuts to 18 N·m
(13 ft. lbs.).

(14) Install the shifter cable bracket and retaining

bolt (Fig. 63).

(15) Connect the shifter cable (Fig. 63).
(16) Install the spring on the shift lever arm (Fig.

63).

(17) Install the throttle valve cable bracket and

retaining fasteners (Fig. 63).

(18) Connect the throttle valve cable (Fig. 63).
(19) Install the transfer case shift cable bracket on

the transmission housing (Fig. 63).

(20) Position the transmission support crossmem-

ber/mount assembly and install the (4) transmission
mount retaining bolts (Fig. 64). Torque the bolts to
75 N·m (55 ft. lbs.).

(21) Install a jack under the transmission support

crossmember and raise slightly.

(22) Install the transfer case on the transmission.

Torque the transfer case retaining nuts to 75 N·m (55
ft. lbs.).

(23) Using the jack, raise the transmission assem-

bly into position and install the (8) transmission sup-
port crossmember retaining bolts (Fig. 64). Torque
the bolts to 41 N·m (30 ft. lbs.).

Fig. 61 Torque Converter Bolt Access Hole

1 - TORQUE CONVERTER BOLT ACCESS HOLE
2 - ENGINE OIL PAN
3 - TOP DEAD CENTER ALIGNMENT TOOL ACCESS HOLE

Fig. 62 Exhaust System Inlet Pipe Retaining Bolts

1 - EXHAUST SYSTEM INLET PIPE RETAINING BOLTS
2 - ENGINE OIL PAN

Fig. 63 Transmission Control Cables and Fluid

Lines

1 - TRANSMISSION SHIFTER CABLE
2 - THROTTLE VALVE CABLE
3 - TRANSFER CASE SHIFTER CABLE
4 - TRANSFER CASE SHIFTER CABLE BRACKET RETAINING
BOLT(S)
5 - THROTTLE VALVE CABLE BRACKET RETAINING BOLT
6 - ELECTRICAL CONNECTORS
7 - TRANSMISSION FLUID LINES

21s - 80

AUTOMATIC - 44RE

WG

AUTOMATIC - 44RE (Continued)

2001 JEEP GRAND CHEROKEE

(24) Unclip the wire harness from the transmis-

sion support crossmember.

(25) Position the exhaust system support brackets

and install the retaining bolts. Torque the bolts to 41
N·m (30 ft. lbs.) (Fig. 64).

(26) Install the vent tube on the transfer case.
(27) Connect the transfer case shift cable on the

shifter arm.

(28) Install the rear driveshaft. Torque the bolts to

32 N·m (24 ft. lbs.). Be certain to install the drive-
shaft in the same position as before removal.

(29) Install the front driveshaft. Torque the bolts

to 32 N·m (24 ft. lbs.) (Fig. 65). Be certain to install
the

driveshaft

in

the

same

position

as

before

removal.

(30) Install the (2) lower fan shroud retaining

bolts. Torque the bolts to 15 N·m (132 in. lbs.).

(31) Lower the vehicle on the hoist.
(32) Install the transmission dipstick tube in the

transmission housing.

(33) Install the transmission dipstick tube support

bracket retaining nut (Fig. 66). Torque the nut to 25
N·m (221 in. lbs.).

(34) Install the (2) upper fan shroud retaining

bolts. Torque the bolts to 15 N·m (132 in. lbs.).

(35) Connect the negative battery cable.

Fig. 64 Transmission Support Crossmember

Position and Orientation

1 - TRANSFER CASE
2 - TRANSMISSION MOUNT RETAINING BOLTS (2 OF 4)
3 - EXHAUST SYSTEM SUPPORT BRACKET RETAINING BOLTS
4 - CROSSMEMBER RETAINING BOLTS
5 - TRANSMISSION
6 - CROSSMEMBER RETAINING BOLTS

Fig. 65 Front Driveshaft Retaining Bolts

1 - TRANSFER CASE
2 - FRONT DRIVESHAFT RETAINING BOLTS
3 - REFERENCE MARK

Fig. 66 Transmission Dipstick Tube Support Bracket

Position and Orientation

1 - TRANSMISSION DIPSTICK TUBE
2 - TURBOCHARGER EXHAUST MANIFOLD HEATSHIELD
3 - TRANSMISSION DIPSTICK TUBE SUPPORT BRACKET
RETAINING NUT

WG

AUTOMATIC - 44RE

21s - 81

AUTOMATIC - 44RE (Continued)

2001 JEEP GRAND CHEROKEE

SCHEMATICS AND DIAGRAMS

HYDRAULIC SCHEMATICS

HYDRAULIC

FLOW

IN

P

ARK

21s - 82

AUTOMATIC - 44RE

WG

AUTOMATIC - 44RE (Continued)

2001 JEEP GRAND CHEROKEE

 

 

 

 

 

 

 

Content   ..  891  892  893  894   ..