Jeep Grand Cherokee WJ. Manual - part 892

 

  Index      Jeep     Jeep Grand Cherokee WJ - service repair manual 2001 year

 

Search            

 

 

 

 

 

 

 

 

 

Content   ..  890  891  892  893   ..

 

 

Jeep Grand Cherokee WJ. Manual - part 892

 

 

(11) Check seal ring on rear clutch retainer hub

and seal rings on input shaft (Fig. 48). Also verify
that shaft seal rings are installed in sequence shown.

(12) Install rear clutch thrust washer (Fig. 49).

Use additional petroleum jelly to hold washer in
place if necessary.

(13) Align clutch discs in front clutch and install

front clutch on rear clutch (Fig. 50). Rotate front
clutch retainer back and forth until completely
seated on rear clutch retainer.

(14) Coat intermediate shaft thrust washer with

petroleum jelly. Then install washer in rear clutch
hub (Fig. 51). Use enough petroleum jelly to hold
washer in place. Be sure grooved side of washer faces
rearward (toward output shaft) as shown. Also note
that washer only fits one way in clutch hub. Note
thickness of this washer. It is a select fit part and is
used to control transmission end play.

Fig. 46 Installing Planetary Geartrain

1 - PLANETARY GEARTRAIN AND INTERMEDIATE SHAFT
ASSEMBLY

Fig. 47 Installing Intermediate Shaft Thrust Plate

1 - INTERMEDIATE SHAFT HUB
2 - INTERMEDIATE SHAFT THRUST PLATE

Fig. 48 Input Shaft Seal Ring Location

1 - INPUT SHAFT
2 - TEFLON SEAL RING
3 - PLASTIC SEAL RING
4 - REAR CLUTCH RETAINER

Fig. 49 Installing Rear Clutch Thrust Washer

1 - REAR CLUTCH RETAINER
2 - REAR CLUTCH THRUST WASHER (FIBER)

WG

AUTOMATIC - 44RE

21s - 75

AUTOMATIC - 44RE (Continued)

2001 JEEP GRAND CHEROKEE

(15) Align drive teeth on rear clutch discs with

small screwdriver (Fig. 52). This makes installation
on front planetary easier.

(16) Raise front end of transmission upward as far

as possible and support case with wood blocks. Front/
rear clutch and oil pump assemblies are easier to
install if transmission is as close to upright position
as possible.

(17) Slide front band into case.

(18) Install front and rear clutch units as assembly

(Fig. 53). Align rear clutch with front annulus gear
and install assembly in driving shell. Be sure output
shaft thrust washer and thrust plate are not dis-
placed during installation.

(19) Carefully work assembled clutches back and

forth to engage and seat rear clutch discs on front
annulus gear. Also be sure front clutch drive lugs are
fully engaged in slots of driving shell after installa-
tion.

(20) Assemble front band strut.
(21) Install front band adjuster, strut and adjust-

ing screw (Fig. 54).

(22) Tighten band adjusting screw until band just

grips clutch retainer. Verify that front/rear clutches
are still seated before continuing.

(23) Check seal rings on reaction shaft support

hub. Verify that seal rings are hooked together and
that the thrust washer is properly positioned (Fig.
55). Use petroleum jelly to hold thrust washer in
place if necessary.

(24) Lubricate oil pump body seal with petroleum

jelly. Lubricate pump shaft seal lip with petroleum
jelly.

(25) Thread two Pilot Stud Tools C-3288-B into

bolt holes in oil pump bore flange (Fig. 56).

(26) Align and install oil pump gasket (Fig. 56).

Fig. 50 Assembling Front And Rear Clutch Units

1 - TURN FRONT CLUTCH BACK & FORTH UNTIL SEATED
2 - REAR CLUTCH ASSEMBLY

Fig. 51 Installing Intermediate Shaft Thrust Washer

1 - INTERMEDIATE SHAFT THRUST WASHER
2 - INPUT SHAFT
3 - REAR CLUTCH RETAINER HUB

Fig. 52 Aligning Rear Clutch Disc Lugs

1 - REAR CLUTCH DISCS
2 - USE SMALL SCREWDRIVER TO ALIGN CLUTCH DISC
TEETH

21s - 76

AUTOMATIC - 44RE

WG

AUTOMATIC - 44RE (Continued)

2001 JEEP GRAND CHEROKEE

(27) Install oil pump (Fig. 57). Align and position

pump on pilot studs. Slide pump down studs and
work it into front clutch hub and case by hand. Then
install 2 or 3 pump bolts to hold pump in place.

(28) Remove pilot stud tools and install remaining

oil pump bolts. Tighten bolts alternately in diagonal
pattern to 20 N·m (15 ft. lbs.).

(29) Measure input shaft end play (Fig. 58).

NOTE: If end play is incorrect, transmission is
incorrectly assembled, or the intermediate shaft
thrust washer is incorrect. The intermediate shaft
thrust washer is selective.

(a) Attach Adapter 8266-6 to Handle 8266-8.
(b) Attach

dial

indicator

C-3339

to

Handle

8266-8.

(c) Install the assembled tool onto the input

shaft of the transmission and tighten the retaining
screw on Adapter 8266-6 to secure it to the input
shaft.

Fig. 53 Installing Front/Rear Clutch Assemblies

1 - INPUT SHAFT
2 - FRONT CLUTCH
3 - REAR CLUTCH

Fig. 54 Front Band Linkage Installation

1 - BAND LEVER
2 - BAND STRUT
3 - FRONT BAND

Fig. 55 Reaction Shaft Support Seal Rings And

Thrust Washer

1 - REACTION SHAFT SUPPORT HUB
2 - THRUST WASHER
3 - SEAL RINGS

Fig. 56 Installing Pilot Studs And Oil Pump Gasket

1 - OIL PUMP GASKET
2 - PILOT STUD TOOLS C-3288-B

WG

AUTOMATIC - 44RE

21s - 77

AUTOMATIC - 44RE (Continued)

2001 JEEP GRAND CHEROKEE

(d) Position the dial indicator plunger against a

flat spot on the oil pump and zero the dial indica-
tor.

(e) Move input shaft in and out and record read-

ing. End play should be 0.56-2.31 mm (0.022-0.091
in.). Adjust as necessary.

(30) Install accumulator piston and inner and

outer springs (Fig. 59).

(31) Verify that valve body solenoid harness is

secured in 3-4 accumulator housing cover plate.

(32) Install valve body as follows:

(a) Align and carefully insert park rod into pawl.

Rod will make click noise as it enters pawl. Move
rod slightly to check engagement.

(b) Align and seat valve body on case. Be sure

manual lever shaft and overdrive connector are
fully seated in case. Also be sure valve body wiring
is not pinched or kinked.

(c) Install and start all valve body attaching

bolts by hand. Then tighten bolts evenly, in a diag-
onal pattern to 12 N·m (105 in. lbs.) torque. Do not
overtighten valve body bolts. This could result in
distortion and cross leakage after installation.

CAUTION: It is possible for the park rod to displace
into a cavity just above the pawl sprag during
installation. Make sure the rod is actually engaged
in the pawl and has not displaced into the cavity.

(33) Install new filter on valve body. Tighten filter

screws to 4 N·m (35 in. lbs.).

(34) Adjust front and rear bands.

Fig. 57 Installing Oil Pump

1 - OIL PUMP
2 - PILOT STUD TOOL
3 - PILOT STUD TOOL

Fig. 58 Checking Input Shaft End Play

1 - TOOL 8266-8
2 - TOOL 8266-6
3 - TOOL C-3339

Fig. 59 Accumulator Piston And Springs

1 - GOVERNOR PRESSURE SENSOR
2 - VALVE BODY
3 - PARK ROD
4 - ACCUMULATOR PISTON
5 - GOVERNOR PRESSURE SOLENOID

21s - 78

AUTOMATIC - 44RE

WG

AUTOMATIC - 44RE (Continued)

2001 JEEP GRAND CHEROKEE

 

 

 

 

 

 

 

Content   ..  890  891  892  893   ..