Jeep Grand Cherokee WJ. Manual - part 682

 

  Index      Jeep     Jeep Grand Cherokee WJ - service repair manual 2001 year

 

Search            

 

 

 

 

 

 

 

 

 

Content   ..  680  681  682  683   ..

 

 

Jeep Grand Cherokee WJ. Manual - part 682

 

 

Symptom:

P1597-SPEED CONTROL SWITCH ALWAYS LOW

When Monitored and Set Condition:

P1597-SPEED CONTROL SWITCH ALWAYS LOW

When Monitored:

With the ignition on and battery voltage above 10.4 volts.

Set Condition:

The PCM detects voltage below 0.39 volt on the S/C switch signal circuit

for at least 2 minutes.

POSSIBLE CAUSES

INTERMITTENT CONDITION

SPEED CONTROL ON/OFF SWITCH

SPEED CONTROL RESUME/ACCEL SWITCH

SPEED CONTROL SWITCH CONTROL CIRCUIT SHORTED TO SENSOR GROUND

SPEED CONTROL SWITCH CONTROL CIRCUIT SHORTED TO GROUND

PCM

TEST

ACTION

APPLICABILITY

1

Turn the ignition on.
With the DRBIII

t, read the Speed Control voltage.

Is the Speed Control voltage below 1.0 volts?

All

Yes

Go To

2

No

Go To

7

2

Turn the ignition on.
With the DRBIII

t, monitor the Speed Control Switch voltage.

Disconnect the Speed Control On/Off Switch harness connector.
Did the volt change to above 4.7 volts?

All

Yes

Replace the Speed Control On/Off Switch.
Perform SPEED CONTROL VERIFICATION - VER-4.

No

Go To

3

3

Turn the ignition on.
With the DRBIII

t, monitor the Speed Control Switch voltage.

Disconnect the Speed Control Resume/Accel Switch harness connector.
Did the volt change to above 4.7 volts?

All

Yes

Replace the Speed Control Resume/Accel Switch.
Perform SPEED CONTROL VERIFICATION - VER-4.

No

Go To

4

284

SPEED CONTROL

TEST

ACTION

APPLICABILITY

4

Turn the ignition off.
Disconnect the Speed Control On/Off Switch harness connector.
Disconnect the Speed Control Resume/Accel Switch harness connector.
Disconnect the PCM harness connector.
Measure the resistance between the Speed Control Switch circuit and the Sensor
ground circuit in the PCM harness connector.
Is the resistance below 5.0 ohms?

All

Yes

Repair the Speed Control Switch Signal circuit shorted to Sensor
ground circuit.
Perform SPEED CONTROL VERIFICATION - VER-4.

No

Go To

5

5

Turn the ignition off.
Disconnect the Speed Control On/Off Switch harness connector.
Disconnect the Speed Control Resume/Accel Switch harness connector.
Disconnect the PCM harness connector.
Measure the resistance of the Speed Control Switch circuit in PCM harness
connector to ground.
Is the resistance below 5.0 ohms?

All

Yes

Repair the Speed Control Switch Signal circuit shorted to ground.
Perform SPEED CONTROL VERIFICATION - VER-4.

No

Go To

6

6

If there are no possible causes remaining, view repair.

All

Repair

Replace the Powertrain Control Module in accordance with the
Service Information.
Perform SPEED CONTROL VERIFICATION - VER-4.

7

WARNING: WHEN THE ENGINE IS OPERATING, DO NOT STAND IN A
DIRECT LINE WITH THE FAN. DO NOT PUT YOUR HANDS NEAR THE
PULLEYS, BELTS OR FAN. DO NOT WEAR LOOSE CLOTHING.
NOTE: The conditions that set the DTC are not present at this time. The
following list may help in identifying the intermittent condition.
With the engine running at normal operating temperature, monitor the DRB
parameters related to the DTC while wiggling the wiring harness. Look for param-
eter values to change and/or a DTC to set.
Review the DTC When Monitored and Set Conditions. If possible, try to duplicate the
conditions under which the DTC was set.
Refer to any Technical Service Bulletins (TSB) that may apply.
Visually inspect the related wiring harness. Look for any chafed, pierced, pinched, or
partially broken wires.
Visually inspect the related wiring harness connectors. Look for broken, bent, pushed
out, or corroded terminals.
Were any of the above conditions present?

All

Yes

Repair as necessary
Perform SPEED CONTROL VERIFICATION - VER-4.

No

Test Complete.

285

SPEED CONTROL

P1597-SPEED CONTROL SWITCH ALWAYS LOW —

Continued

Symptom:

*CHECKING THE SPEED CONTROL OPERATION

POSSIBLE CAUSES

BRAKE LAMP SWITCH

CHECKING THE VEHICLE SPEED SIGNAL

CRUISE INDICATOR

GROUND CIRCUIT OPEN

INSTRUMENT CLUSTER

PCM - BRAKE SW SIGNAL

PCM - S/C INDICATOR

PCM - S/C SIGNAL

S/C SWITCH SIGNAL CIRCUIT OPEN

S/C SWITCH SIGNAL CIRCUIT SHORTED TO GROUND

S/C SWITCHES

SECONDARY BRAKE SWITCH SIGNAL CIRCUIT OPEN

SECONDARY BRAKE SWITCH SIGNAL CIRCUIT SHORTED TO GROUND

SENSOR GROUND CIRCUIT OPEN

TEST

ACTION

APPLICABILITY

1

Start the engine.
With the DRB, select Engine, JTEC then Sensor Display.
Observe the cruise switch volts on the DRB while pressing and holding each cruise
button separately.
NOTE: Pressing each cruise button should result in the following voltages:
ON/OFF 0.55 - 1.15v, SET 3.15 - 3.6v, RESUME/ACCEL 3.9 - 4.15v, CANCEL 1.55
- 2.05v, COAST 2.5 - 3.0v, No Button Pressed 4.4 - 4.7v
Does each switch provide the correct voltage?

All

Yes

Go To

2

No

Go To

12

2

Start the engine.
Observe the S/C Indicator while pressing the S/C ON/OFF button several times,
pausing for 5 seconds between each time.
Does the S/C indicator turn on and off properly?

All

Yes

Go To

3

No

Go To

10

286

SPEED CONTROL

TEST

ACTION

APPLICABILITY

3

Turn the ignition on.
With the DRB, select Engine, JTEC and Inputs/Outputs.
Observe the Brake Switch input while pressing and releasing the brake pedal several
times.
Does the DRB indicate the correct change of state from Released to Pressed?

All

Yes

Go To

4

No

Go To

5

4

With the DRB, monitor the Vehicle Speed Signal while test driving the vehicle.
Does the DRB display accurate vehicle speed?

All

Yes

Test Complete.

No

Refer to symptom list for problems related to Vehicle Speed
Sensor Signal.
Perform SPEED CONTROL VERIFICATION - VER-4.

5

Turn the ignition off.
Disconnect the Brake Lamp Switch harness connector.
Turn the ignition on.
Measure the voltage of the Secondary Brake Switch Signal circuit.
Is the voltage above 9.0 volts?

All

Yes

Go To

6

No

Go To

8

6

Turn the ignition off.
Disconnect the Brake Switch harness connector.
With the DRB, monitor the brake switch input.
Connect a jumper wire between the Brake Lamp Switch harness connector cavities
1 and 2.
Did the DRB display change from Pressed to Released?

All

Yes

Adjust or replace the Brake Lamp Switch.
Perform SPEED CONTROL VERIFICATION - VER-4.

No

Go To

7

7

Disconnect the Brake Lamp Switch harness connector.
Measure the resistance between ground and the Brake Lamp Switch harness
connector cavity 2.
Is the resistance below 5.0 ohms?

All

Yes

Replace and program the PCM in accordance with the Service
Information.
Perform SPEED CONTROL VERIFICATION - VER-4.

No

Repair the Ground circuit for an open.
Perform SPEED CONTROL VERIFICATION - VER-4.

287

SPEED CONTROL

*CHECKING THE SPEED CONTROL OPERATION —

Continued

 

 

 

 

 

 

 

Content   ..  680  681  682  683   ..