Jeep Grand Cherokee WJ. Manual - part 668

 

  Index      Jeep     Jeep Grand Cherokee WJ - service repair manual 2001 year

 

Search            

 

 

 

 

 

 

 

 

 

Content   ..  666  667  668  669   ..

 

 

Jeep Grand Cherokee WJ. Manual - part 668

 

 

TEST

ACTION

APPLICABILITY

9

WARNING: WHEN THE ENGINE IS OPERATING, DO NOT STAND IN A
DIRECT LINE WITH THE FAN. DO NOT PUT YOUR HANDS NEAR THE
PULLEYS, BELTS OR FAN. DO NOT WEAR LOOSE CLOTHING.
NOTE: The conditions that set the DTC are not present at this time. The
following list may help in identifying the intermittent condition.
With the engine running and at normal operating temperature, monitor the DRB
parameters related to the DTC while wiggling the wiring harness. Look for param-
eter values to change and/or a DTC to set.
Review the DTC When Monitored and Set Conditions. If possible, try to duplicate the
conditions under which the DTC was set.
Refer to any Technical Service Bulletins (TSB) that may apply.
Visually inspect the related wiring harness. Look for any chafed, pierced, pinched, or
partially broken wires.
Visually inspect the related wiring harness connectors. Look for broken, bent, pushed
out, or corroded terminals.
Were any of the above conditions present?

without 45RFE

AUTO TRANS

Yes

Repair as necessary
Perform TRANSMISSION VERIFICATION TEST VER - 1.

No

Test Complete.

228

DRIVEABILITY - DIESEL

P1765-TRANS 12 VOLT SUPPLY RELAY CTRL CIRCUIT —

Continued

Symptom:

*CHECKING THE A/C SYSTEM

POSSIBLE CAUSES

A/C COMPRESSOR CLUTCH

A/C COMPRESSOR CLUTCH GROUND CIRCUIT OPEN

A/C COMPRESSOR CLUTCH RELAY OUTPUT CIRCUIT OPEN

A/C HIGH PRESSURE SWITCH OPEN

A/C LOW PRESSURE SWITCH OPEN

A/C PRESSURE SENSE CIRCUIT OPEN

A/C SWITCH INPUT TO BCM

A/C SWITCH INPUT TO PCM

A/C SWITCH SIGNAL OPEN

A/C SWITCH SIGNAL SHORTED TO GROUND

ACTUATOR TEST

ECM

ECM - A/C SWITCH INPUT

ECM - PRESSURE SIGNAL OPEN

FUSED B+ CIRCUIT OPEN

GROUND CIRCUIT OPEN

HI PRESSURE SIGNAL CIRCUIT OPEN

PCM - A/C SWITCH INPUT

TEST

ACTION

APPLICABILITY

1

NOTE: Prior to diagnosing the A/C electrical system, check for proper A/C
system pressure. Improper refrigerant charge can cause incorrect system
diagnosis and unnecessary component replacement.
NOTE: Refer to the Service Information to check the A/C mechanical system
before continuing.
With the DRB, select Body, Body Computer then Inputs/Outputs.
Start the engine and set the blower to Panel.
Turn the A/C on.
With the DRB, read the A/C Select Switch status.
Does the DRB display A/C Select Switch YES?

All

Yes

Go To

2

No

Refer to symptom list for problems related to A/C Select Switch
Operation.
Perform ROAD TEST VERIFICATION - VER-2.

229

DRIVEABILITY - DIESEL

TEST

ACTION

APPLICABILITY

2

With the DRB, select Engine, JTEC then Inputs/Outputs.
Start the engine and set the blower to Panel.
Turn the A/C on.
With the DRB, read the A/C Select Switch.
Does the DRB display A/C Select Switch ON?

All

Yes

Go To

3

No

Replace the PCM (JTEC) in accordance with the Service Infor-
mation.
Perform ROAD TEST VERIFICATION - VER-2.

3

With the DRB, select Engine, Bosch Controller then Inputs/Outputs.
Start the engine and set the blower to Panel.
Turn the A/C on.
With the DRB, read the A/C Switch status.
Does the DRB display A/C Switch ON?

All

Yes

Go To

4

No

Go To

14

4

Turn the ignition on.
With the DRB, select Engine, Bosch Controller then Inputs/Outputs.
Read the A/C H/L Press Sw status.
Does the DRB display A/C H/L Press Sw ON?

All

Yes

Go To

5

No

Go To

9

5

Turn the ignition on.
With the DRBIII

t, actuate the A/C Compressor Clutch Relay.

Observe the A/C Compressor Clutch during actuation.
Is the A/C Compressor Clutch clicking?

All

Yes

The electrical portion of the A/C System is operating properly.
Perform ROAD TEST VERIFICATION - VER-2.

No

Go To

6

6

Remove the A/C Compressor Clutch Relay from the PDC.
Using a 12-volt test light connected to ground, check the Fused B+ circuit.
Is the test light on?

All

Yes

Go To

7

No

Repair the Fused B+ circuit for an open.
Perform ROAD TEST VERIFICATION - VER-2.

7

Remove the A/C Compressor Clutch Relay from the PDC.
Disconnect the A/C Compressor Clutch harness connector.
Connect a jumper wire across the A/C Compressor Clutch Relay connector cavities 30
and 87 in the PDC.
Using a 12-volt test light connected to ground, check the A/C Compressor Clutch
Relay Output circuit in the A/C Compressor Clutch harness connector.
Is the test light on?

All

Yes

Go To

8

No

Repair the A/C Compressor Clutch Relay Output circuit for an
open.
Perform ROAD TEST VERIFICATION - VER-2.

230

DRIVEABILITY - DIESEL

*CHECKING THE A/C SYSTEM —

Continued

TEST

ACTION

APPLICABILITY

8

Disconnect the A/C Compressor Clutch harness connector.
Using a 12-volt test light connected to 12 volts, check the A/C Compressor Clutch
Ground circuit.
Is the test light on?

All

Yes

Replace the A/C Compressor Clutch in accordance with the
Service Information.
Perform ROAD TEST VERIFICATION - VER-2.

No

Repair the A/C Compressor Clutch Ground circuit for an open.
Perform ROAD TEST VERIFICATION - VER-2.

9

Turn the ignition on.
Connect one end of a jumper wire to ground and back probe the A/C Pressure Signal
circuit at the ECM harness connector.
With the DRB, select Engine, Bosch Controller then Inputs/Outputs.
Read the A/C H/L Press Sw status.
Does the DRB display A/C H/L Press Sw ON?

All

Yes

Go To

10

No

Replace and program the ECM in accordance with the Service
Information.
Perform ROAD TEST VERIFICATION - VER-2.

10

Disconnect the A/C High Pressure Switch harness connector.
Turn the ignition on.
Connect one end of a jumper wire to ground and back probe the A/C Pressure Signal
circuit at the A/C High Pressure Switch harness connector.
With the DRB, select Engine, Bosch Controller then Inputs/Outputs.
Read the A/C H/L Press Sw status.
Does the DRB display A/C H/L Press Sw ON?

All

Yes

Go To

11

No

Repair the A/C Pressure Signal circuit for an open between the
ECM and the A/C High Pressure Switch.
Perform ROAD TEST VERIFICATION - VER-2.

11

Turn the ignition off.
Disconnect the A/C High Pressure Switch harness connector.
Measure the resistance of the A/C High Pressure Switch.
Is the resistance below 10.0 ohms?

All

Yes

Go To

12

No

Replace the A/C High Pressure Switch.
Perform ROAD TEST VERIFICATION - VER-2.

12

Disconnect the A/C Low Pressure Switch harness connector.
Turn the ignition on.
Connect one end of a jumper wire to ground and the other end to the A/C Pressure
Sense circuit at the A/C Low Pressure Switch harness connector.
With the DRB, select Engine, Bosch Controller then Inputs/Outputs.
Read the A/C H/L Press Sw status.
Does the DRB display A/C H/L Press Sw ON?

All

Yes

Go To

13

No

Repair the A/C Pressure Sense circuit for an open between the
A/C High Pressure Switch and the A/C Low Pressure Switch.
Perform ROAD TEST VERIFICATION - VER-2.

231

DRIVEABILITY - DIESEL

*CHECKING THE A/C SYSTEM —

Continued

 

 

 

 

 

 

 

Content   ..  666  667  668  669   ..