Jeep Grand Cherokee WJ. Manual - part 651

 

  Index      Jeep     Jeep Grand Cherokee WJ - service repair manual 2001 year

 

Search            

 

 

 

 

 

 

 

 

 

Content   ..  649  650  651  652   ..

 

 

Jeep Grand Cherokee WJ. Manual - part 651

 

 

Symptom List:

P1515-ACCEL. PEDAL SENSOR PLAUSIBILITY
P1515-ACCEL. PEDAL SENSOR PWG PLAUS WITH POTENTIOME-
TER
P1515-ACCEL. PEDAL SENSOR SIGNAL HIGH EXCEEDED
P1515-ACCEL. PEDAL SENSOR SUPPLY HIGH EXCEEDED
P1515-ACCEL. PEDAL SENSOR SUPPLY LOW EXCEEDED

Test Note:

All symptoms listed above are diagnosed using the same tests.

The title for the tests will be P1515-ACCEL. PEDAL SENSOR
PLAUSIBILITY.

When Monitored and Set Condition:

P1515-ACCEL. PEDAL SENSOR PLAUSIBILITY

When Monitored:

With the ignition on.

Set Condition:

The accelerator pedal position sensor signal is below 0.2 volt (4%) or above

4.5 volts (90%) and the idle switch is not in the correct state. NOTE: The idle switch is
designed to transition when the accel position is approximately 16% (1.00 volt). This code
sets the ECM to Limp-in Mode, which includes a fixed engine speed of 1100 RPM.

P1515-ACCEL. PEDAL SENSOR PWG PLAUS WITH POTENTIOMETER

When Monitored:

With the ignition on.

Set Condition:

The accelerator pedal position sensor signal is below 0.20 volts, the idle

switch transitions at too high a percentage intermittently or the idle switch is not in the
correct state intermittently. NOTE: The idle switch is designed to transition when the accel
position is approximately 16% (1.00 volt). This code sets the ECM to Limp-in Mode, which
includes a fixed engine speed of 1100 RPM.

P1515-ACCEL. PEDAL SENSOR SIGNAL HIGH EXCEEDED

When Monitored:

With the ignition on.

Set Condition:

The accelerator pedal position sensor signal voltage is above 4.5 volts.

NOTE: This code sets the ECM to Limp-in Mode, which includes a fixed engine speed of
1100 RPM.

P1515-ACCEL. PEDAL SENSOR SUPPLY HIGH EXCEEDED

When Monitored:

With the ignition on.

Set Condition:

The ECM detects voltage on the accelerator pedal position sensor 5-volt

supply circuit above 5.2 volts.

P1515-ACCEL. PEDAL SENSOR SUPPLY LOW EXCEEDED

When Monitored:

With the ignition on.

Set Condition:

The ECM detects voltage the accelerator pedal position sensor 5-volt

supply circuit below 4.75 volts.

160

DRIVEABILITY - DIESEL

POSSIBLE CAUSES

APP SENSOR IDLE VOLTAGE

APP SENSOR WIDE OPEN THROTTLE VOLTAGE

ECM - 5-VOLT SUPPLY CIRCUIT

ECM SENSOR GROUND CIRCUIT OPEN

LOW IDLE POSITION SWITCH SENSE CIRCUIT SHORTED TO GROUND

PCM - SENSOR GROUND CIRCUIT

INTERMITTENT CONDITION

5-VOLT SUPPLY CIRCUIT OPEN

APP SENSOR SIGNAL CIRCUIT OPEN

LOW IDLE POSITION SWITCH SENSE CIRCUIT OPEN

5-VOLT SUPPLY CIRCUIT SHORTED TO THE SENSOR GROUND CIRCUIT

VERIFY LOW IDLE POSITION SWITCH OPERATION

APP SENSOR SIGNAL CIRCUIT SHORTED TO GROUND

5-VOLT SUPPLY CIRCUIT SHORTED TO GROUND

PCM SENSOR GROUND CIRCUIT OPEN

VERIFY APP SENSOR OPERATION

APP SENSOR SIGNAL CIRCUIT SHORTED TO THE SENSOR GROUND CIRCUIT

LOW IDLE POSITION SWITCH SENSE CIRCUIT SHORTED TO THE SENSOR GROUND CIR-
CUIT

5-VOLT SUPPLY CIRCUIT SHORTED TO VOLTAGE

ECM - SENSOR GROUND OPEN

APP SENSOR CIRCUIT SHORTED TO VOLTAGE

LOW IDLE POSITION SWITCH SENSE CIRCUIT SHORTED TO VOLTAGE

VERIFY CORRECT SWITCHING

ECM - APP SENSOR SIGNAL CIRCUIT

TEST

ACTION

APPLICABILITY

1

Turn the ignition off.
Disconnect the APP Sensor harness connector.
Connect one end of a jumper wire to APP Sensor harness connector cavity 4.
Turn the ignition on.
With the DRB III, monitor the Low Idle Position Switch input while tapping the other
end of the jumper wire to APP Sensor harness connector cavity 5.
Does the DRB III change between IDLE and ABOVE IDLE when tapping the jumper
wire?

All

Yes

Go To

2

No

Go To

8

161

DRIVEABILITY - DIESEL

P1515-ACCEL. PEDAL SENSOR PLAUSIBILITY —

Continued

TEST

ACTION

APPLICABILITY

2

Turn the ignition off.
Disconnect the APP Sensor harness connector.
Disconnect the ECM harness connectors.
Measure the resistance of the Low Idle Position Switch Sense circuit.
Is the resistance below 5.0 ohms?

All

Yes

Go To

3

No

Repair the Low Idle Position Switch Sense circuit for an open.
Perform ROAD TEST VERIFICATION - VER-2.

3

Turn the ignition off.
Disconnect the APP Sensor harness connector.
Disconnect the ECM harness connectors.
Measure the resistance between ground and the Low Idle Position Switch Sense
circuit.
Is the resistance above 100 kohms?

All

Yes

Go To

4

No

Repair the Low Idle Position Switch Sense circuit for a short to
ground.
Perform ROAD TEST VERIFICATION - VER-2.

4

Turn the ignition off.
Disconnect the APP Sensor harness connector.
Disconnect the PCM harness connectors.
Measure the resistance of the Sensor Ground circuit between APP Sensor harness
connector cavity 4 and the PCM harness connector.
Is the resistance below 5.0 ohms?

All

Yes

Go To

5

No

Repair the PCM APP Sensor Ground circuit for an open.
Perform ROAD TEST VERIFICATION - VER-2.

5

Turn the ignition off.
Disconnect the APP Sensor harness connector.
Disconnect the ECM harness connectors.
Measure the resistance between the Low Idle Position Switch Sense circuit and the
Sensor Ground circuits at cavity 4 and 8 of the APP Sensor harness connector.
Is the resistance above 100 kohms for both measurements?

All

Yes

Go To

6

No

Repair the Low Idle Position Switch Sense circuit and Sensor
Ground circuit for a short together.
Perform ROAD TEST VERIFICATION - VER-2.

162

DRIVEABILITY - DIESEL

P1515-ACCEL. PEDAL SENSOR PLAUSIBILITY —

Continued

TEST

ACTION

APPLICABILITY

6

Turn the ignition off.
Disconnect the APP Sensor harness connector.
Disconnect the ECM harness connectors.
Remove the ASD/Diesel Power Relay from the PDC.
Connect a jumper wire between cavity 30 and cavity 87 ASD/Diesel Power Relay
connector.
Turn the ignition on.
Measure the voltage of the Low Idle Position Switch Sense circuit.
Is the voltage above 1.0 volt?

All

Yes

Repair the Low Idle Position Switch Sense circuit for a short to
voltage.
Perform ROAD TEST VERIFICATION - VER-2.

No

Go To

7

7

If there are no possible causes remaining, view repair.

All

Repair

Replace and program the Engine Control Module in accordance
with the Service Information.
Perform ROAD TEST VERIFICATION - VER-2.

8

Turn the ignition on.
With the DRB III observe the Low Idle Position Switch input.
Press and release the accelerator pedal several times while observing the DRB III
display.
NOTE: The Low Idle Position Switch input should change from IDLE to
ABOVE IDLE when pressing and releasing the accelerator pedal.
Did Low Idle Position Switch input change between IDLE and ABOVE IDLE?

All

Yes

Go To

9

No

Replace the Accelerator Pedal Position Sensor in accordance with
the Service Information.
Perform ROAD TEST VERIFICATION - VER-2.

9

Turn the ignition off.
Disconnect the APP Sensor harness connector.
Turn the ignition on.
Measure the voltage of the 5-volt Supply circuit in APP Sensor harness connector
cavity 10.
Is the voltage between 4.7 and 5.3 volts?

All

Yes

Go To

10

No

Go To

23

10

Turn the ignition off.
Disconnect the APP Sensor harness connector.
Connect a jumper wire between APP Sensor harness connector cavities 7 and 10.
With the DRBIII, read the PEDAL OUTPUT VOLTS.
Does the DRBIII display between 4.0 and 5.5 volts?

All

Yes

Go To

11

No

Go To

18

163

DRIVEABILITY - DIESEL

P1515-ACCEL. PEDAL SENSOR PLAUSIBILITY —

Continued

 

 

 

 

 

 

 

Content   ..  649  650  651  652   ..