Jeep Grand Cherokee WJ. Manual - part 640

 

  Index      Jeep     Jeep Grand Cherokee WJ - service repair manual 2001 year

 

Search            

 

 

 

 

 

 

 

 

 

Content   ..  638  639  640  641   ..

 

 

Jeep Grand Cherokee WJ. Manual - part 640

 

 

TEST

ACTION

APPLICABILITY

14

Turn the ignition off.
Remove the Transmission Control Relay from the PDC.
Disconnect the PCM harness connectors.
Check connectors - Clean/repair as necessary
Measure the resistance between the Torque Converter Clutch Solenoid Control
circuit in PCM C2 harness connector cavity 11 and PCM C2 harness connector
cavities 1, 8, 21, 29 31 and C1 cavity 4.
NOTE: The resistance should be 28.0 - 68.0 ohms between PCM C2 harness
connector cavity 11 and PCM C2 harness connector cavity 8.
NOTE: The resistance should be 50.0 - 120.0 ohms between PCM C2 harness
connector cavity 11 and PCM C2 harness connector cavity 21.
NOTE: The resistance between PCM C2 harness connector cavity 11 and all
other cavities listed should be above 100 kohms.
Measure the resistance between the Torque Converter Clutch Solenoid Control
circuit in PCM C2 harness connector cavity 11 and Transmission Control Relay
Output circuit cavity in the Transmission Control Relay connector.
NOTE: The resistance should be 25.0 - 60.0 ohms between the Torque
Converter Clutch Solenoid Control circuit in PCM C2 harness connector
cavity 11 and the Transmission Control Relay Output circuit.
Are the resistances between circuits what they are supposed to be?

without 45RFE

AUTO TRANS

Yes

Go To

15

No

Replace the Transmission Solenoid Assembly in accordance with
the Service Information.
Perform TRANSMISSION VERIFICATION TEST VER - 1.

15

If there are no possible causes remaining, view repair.

without 45RFE

AUTO TRANS

Repair

Replace and program the Powertrain Control Module in accor-
dance with the Service Information.
Perform TRANSMISSION VERIFICATION TEST VER - 1.

16

WARNING: WHEN THE ENGINE IS OPERATING, DO NOT STAND IN A
DIRECT LINE WITH THE FAN. DO NOT PUT YOUR HANDS NEAR THE
PULLEYS, BELTS OR FAN. DO NOT WEAR LOOSE CLOTHING.
NOTE: The conditions that set the DTC are not present at this time. The
following list may help in identifying the intermittent condition.
With the engine running and at normal operating temperature, monitor the DRB
parameters related to the DTC while wiggling the wiring harness. Look for param-
eter values to change and/or a DTC to set.
Review the DTC When Monitored and Set Conditions. If possible, try to duplicate the
conditions under which the DTC was set.
Refer to any Technical Service Bulletins (TSB) that may apply.
Visually inspect the related wiring harness. Look for any chafed, pierced, pinched, or
partially broken wires.
Visually inspect the related wiring harness connectors. Look for broken, bent, pushed
out, or corroded terminals.
Were any of the above conditions present?

without 45RFE

AUTO TRANS

Yes

Repair as necessary
Perform TRANSMISSION VERIFICATION TEST VER - 1.

No

Test Complete.

116

DRIVEABILITY - DIESEL

P0743-TORQUE CONVERTER CLUTCH SOLENOID/TRANS RELAY CIR-
CUITS —

Continued

Symptom:

P0748-GOVERNOR PRESSURE SOL CONTROL/TRANS RELAY CIR-
CUITS

When Monitored and Set Condition:

P0748-GOVERNOR PRESSURE SOL CONTROL/TRANS RELAY CIRCUITS

When Monitored:

With the ignition on and battery voltage above 10.4 volts.

Set Condition:

The PCM detects low voltage on the governor pressure solenoid control

circuit when the solenoid is commanded off; or excess current on the governor pressure
solenoid control circuit when attempting to command the solenoid on.

POSSIBLE CAUSES

INTERMITTENT CONDITION

GOVERNOR PRESSURE SOLENOID CONTROL CIRCUIT SHORTED TO VOLTAGE

GOVERNOR PRESSURE SOLENOID CONTROL CIRCUIT SHORTED TO GROUND

TRANSMISSION CONTROL RELAY FUSED B+ OPEN

GOVERNOR PRESSURE SOLENOID CONTROL CIRCUIT SHORTED TO OTHER CIRCUITS

TRANSMISSION CONTROL RELAY OUTPUT CIRCUIT SHORTED TO GROUND

GOVERNOR PRESSURE SOLENOID CONTROL CIRCUIT OPEN

TRANS CONTROL RELAY OUTPUT CIRCUIT SHORTED TO OTHER CIRCUITS

GOVERNOR PRESSURE SOLENOID CONTROL CIRCUIT SHORTED TO GROUND INSIDE
TRANS

TRANSMISSION CONTROL RELAY OUTPUT CIRCUIT OPEN

TRANSMISSION CONTROL RELAY

GOVERNOR PRESSURE SOLENOID CONTROL CIRCUIT SHORTED TO OTHER CIRCUIT IN-
SIDE TRANS

TRANSMISSION SOLENOID ASSEMBLY

POWERTRAIN CONTROL MODULE

TEST

ACTION

APPLICABILITY

1

NOTE: If DTC P1765 Trans 12 Volt Supply Relay Ctrl Circuit is present with
this DTC, refer to the Symptom List and diagnose symptom P1765 Trans 12
Volt Supply Relay Ctrl Circuit before proceeding.
Turn the ignition on.
With the DRB, read PCM DTCs.
Is the Starts Since Set counter for P0748 displayed and equal to 0?

without 45RFE

AUTO TRANS

Yes

Go To

2

No

Go To

16

117

DRIVEABILITY - DIESEL

TEST

ACTION

APPLICABILITY

2

Turn the ignition on.
With the DRB, read PCM DTCs.
Are DTCs P0743 and P0753 present with this DTC but without P1765?

without 45RFE

AUTO TRANS

Yes

Go To

3

No

Go To

9

3

Turn the ignition off.
Remove the Transmission Control Relay from the PDC.
Using a 12-volt test light connected to ground, check the Fused B+ circuit.
Did the test light illuminate brightly?

without 45RFE

AUTO TRANS

Yes

Go To

4

No

Repair the Transmission Control Relay Fused B+ circuit for an
open.
Perform TRANSMISSION VERIFICATION TEST VER - 1.

4

Turn the ignition off.
Remove the Transmission Control Relay from the PDC.
Disconnect the Transmission Solenoid Assembly harness connector.
Check connectors - Clean/repair as necessary.
Measure the resistance between ground and the Transmission Control Relay Output
circuit in the Transmission Control Relay connector.
Is the resistance above 100 kohms?

without 45RFE

AUTO TRANS

Yes

Go To

5

No

Repair the Transmission Control Relay Output circuit for a short
to ground.
Perform TRANSMISSION VERIFICATION TEST VER - 1.

5

Turn the ignition off.
Remove the Transmission Control Relay from the PDC.
Disconnect the PCM harness connectors.
Disconnect the Transmission Solenoid Assembly harness connector.
Check connectors - Clean/repair as necessary
Measure the resistance between the Transmission Control Relay Output circuit and
all other circuits in the Transmission Solenoid Assembly harness connector.
Is the resistance below 100 kohms between any two circuits?

without 45RFE

AUTO TRANS

Yes

Repair the circuits that measured below 100 kohms for a short
together.
Perform TRANSMISSION VERIFICATION TEST VER - 1.

No

Go To

6

6

Turn the ignition off.
Remove the Transmission Control Relay from the PDC.
Disconnect the Transmission Solenoid Assembly harness connector.
Check connectors - Clean/repair as necessary.
Measure the resistance of the Transmission Control Relay Output circuit between
the Transmission Control Relay connector and the Transmission Solenoid Assembly
harness connector.
Is the resistance below 5.0 ohms?

without 45RFE

AUTO TRANS

Yes

Go To

7

No

Repair the Transmission Control Relay Output circuit for an
open.
Perform TRANSMISSION VERIFICATION TEST VER - 1.

118

DRIVEABILITY - DIESEL

P0748-GOVERNOR PRESSURE SOL CONTROL/TRANS RELAY CIR-
CUITS —

Continued

TEST

ACTION

APPLICABILITY

7

Turn the ignition off.
Remove the Transmission Control Relay from the PDC.
Check connectors - Clean/repair as necessary.
Install a substitute relay in place of the Transmission Control Relay.
Turn the ignition on.
With the DRB, erase PCM DTCs.
Start the engine.
With the DRB, read PCM DTCs.
Does the DRB display this DTC?

without 45RFE

AUTO TRANS

Yes

Go To

8

No

Replace the Transmission Control Relay.
Perform TRANSMISSION VERIFICATION TEST VER - 1.

8

If there are no possible causes remaining, view repair.

without 45RFE

AUTO TRANS

Repair

Replace the Transmission Solenoid Assembly in accordance with
the Service Information.
Perform TRANSMISSION VERIFICATION TEST VER - 1.

9

Turn the ignition off.
Disconnect the Transmission Solenoid Assembly harness connector.
Disconnect the PCM C2 harness connector.
Check connectors - Clean/repair as necessary.
Turn the ignition on.
Measure the voltage of the Governor Pressure Solenoid Control circuit in the PCM C2
harness connector.
Is the voltage above 1.0 volt?

without 45RFE

AUTO TRANS

Yes

Repair the Governor Pressure Solenoid Control circuit for a short
to voltage.
Perform TRANSMISSION VERIFICATION TEST VER - 1.

No

Go To

10

10

Turn the ignition off.
Disconnect the Transmission Solenoid Assembly harness connector.
Disconnect the PCM harness connectors.
Check connectors - Clean/repair as necessary
Measure the resistance between ground and the Governor Pressure Solenoid Control
circuit in the PCM C2 harness connector.
Is the resistance above 100 kohms?

without 45RFE

AUTO TRANS

Yes

Go To

11

No

Repair the Governor Pressure Solenoid Control circuit for a short
to ground.
Perform TRANSMISSION VERIFICATION TEST VER - 1.

119

DRIVEABILITY - DIESEL

P0748-GOVERNOR PRESSURE SOL CONTROL/TRANS RELAY CIR-
CUITS —

Continued

 

 

 

 

 

 

 

Content   ..  638  639  640  641   ..